MULTISPAN VPR 126 User manual

R
NC C NO
V
SET
LL3
VPR 126
L1
RL2 L3
24 0
45
NL1 L2 N
VPR 126
FEATURES :
INPUT SPECIFICATION :
DISPLAY AND KEY :
OUTPUT SPECIFICATION :
AUXILIARY SUPPLY :
GENERAL SPECIFICATION :
Protection Available
3 digit bright LED display,
Auto/ Manual/ZVR Reset Option
Time parameter: Power on delay, Trip delay
Recovery time ( Auto Reset )
Over Voltage Asymmetry
Over Frequency Phase Sequence
Under Voltage Phase Loss
Under Frequency
Direct Voltage AC
Frequency
Resolution
Accuracy
VOLTAGE PROTECTION RELAY
50 to 300V AC (L - N) 3Ø-4W/ 1Ø-2W
85 to 520V AC (L - L) 3Ø-3W
45.0 Hz to 65.0 Hz
Class 1.0
Display
Relay
Supply voltage
Dimension (mm)
Keys
Relay Type
Power consumption
(VA RATING)
Rating
Trip Setting
3 digit, 1line, 7 seg, 0.4” RED LED
1 nos.
75 (H) x 45 (W) x 110 (D) mm
SET, INC, DEC/RST
1 C/O (NO-C-NC)
3 VA @ 230V AC MAX
ENVIRONMENT CONDITION :
NETWORK CONNECTION :
Relative Humidity
Protection Level
(As per request)
Operating Temp. 0°C to 55°C
UP to 95% RH
(non-condensing)
IP-65 (Front side) As per IS/IEC
60529 : 2001
100 to 270V AC, 50-60Hz
TECHNICAL SPECIFICATION
MECHANICAL INSTALLATION
Front View(mm)
1 Volt
Time Parameter Power ON Delay Time : 0 To 99 Sec.
Trip delay Time : 0 To 999 Sec.
Recovery Time : 0 To 99 Sec.
L1
L N
R
NC C NO
L2 L3 N
SET
VPR 126
L1R L2 L3
V
R
Y
B
N
TO
LOAD
TERMINAL CONNECTION
110
75 75
Side View(mm)
Over Frequency : 45.0 Hz To 65.0 Hz
Under Frequency : 45.0 Hz To 65.0 Hz
Phase Asymmetry : 2-30%
Under Voltage : 85-520V AC 3Ø-3W
50-300V AC 3Ø-4W/1Ø-2W
Over Voltage : 85-550V AC 3Ø-3W
50-330V AC 3Ø4W/1Ø2W
10A, 230V AC
3Ø-3W/3Ø-4W/1Ø-2W
Network Selection 3Ø-3W/3Ø-4W/1Ø-2W
Class 1.0 (Standard)
ACCURACY
Page -1

KEY OPERATION
To enter in parameter setting
To view individual phase voltage
To Scroll & Hold Page
PRESS KEYFUNCTION
OPERATOR MODE
PARAMETER SETTING MODE
It is used to set parameter value
and to be save & exit from menu
To increment value in parameter
setting
To decrement value in parameter
setting
For 5 sec
SET
SET
OR
SET
Read complete instructions prior to installation
and operation of the unit.
WARNING : Risk of electric shock.
SAFETY PRECAUTION
!
All safety related codifications, symbols and instructions
that appear in this operating manual or on the equipment
must be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
If all the equipment is not handled in a manner specified
by the manufacturer, it might impair the protection provided
by the equipment.
WARNING GUIDELINES
WARNING : Risk of electric shock.
1) To prevent the risk of electric shock, power supply to the
equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
being supplied.
2) To reduce electro magnetic interference, use wire with
adequate rating and twists of the same of equal size shall
be made with shortest connection.
3. Cable used for connection to power source, must have a
cross section of 1mm or greater. These wires should have
insulations capacity made of at least 1.5kV.
4) A better anti-noise effect can be expected by using
standard power supply cable for the instrument.
1) Do not allow pieces of metal, wire clippings, or fine
metallic fillings from installation to enter the product or
else it may lead to a safety hazard that may in turn
endanger life or cause electrical shock to the operator.
2) Circuit breaker or mains switch must be installed
between power source and supply terminal to facilitate
power ‘ON’ or ‘OFF’ function. However this mains switch
or circuit breaker must be installed at convenient place
normally accessible to the operator.
INSTALLATION GUIDELINES
3) Use and store the instrument within the specified ambient
temperature and humidity ranges as mentioned in this
manual.
MECHANICAL INSTALLATION
DISPLAY PAGE
1) To install the instrument on a DIN rail, raise the clamp at the
back of the instrument and place it on the rail. Now release
the clamp, so the instrument fits on the DIN rail.
2) Ensure proper fitting of the instrument by pulling it outwards.
3) To remove the instrument raise the clamp to release it from
the DIN rail.
1) The equipment should be cleaned regularly to avoid
blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth. Do not use
isopropyl alcohol or any other cleaning agent.
MAINTENANCE
3) Fusible resistor must not be replaced by operator.
+
3Ø-4W 1Ø-2W
1) Voltage L1-N 1) Voltage L1-L2 1) Voltage L1-N
2) Voltage L2-N 2) Voltage L2-L3
3) Voltage L3-N 3) Voltage L3-L1
4) Frequency 4) Frequency
2) Frequency
2 4 0 4 1 5 2 4 0
3 3 0 4 0 0
2 5 0 4 3 0
5 0. 0 5 0. 0
5 0. 0
L1 L1 L1L2 L2 L2L3 L3 L3R R R
L1 L1L2 L2L3 L3R R
L1 L1
L1 L1
L1
L2 L2
L2 L2
L2
L3 L3
L3 L3
L3
R R
R R
R
4) The equipment in its installed state must not come in
close proximity to any heating source, caustic vapors, oil
steam, or other unwanted process byproducts.
5) Do not connect anything to unused terminals.
To reset the relay contact in
manual mode after tripping
3Ø-3W
Page -2

PARAMETER SETTING
Password
Over Voltage
(Enable/Disable)
(Enable/Disable)
(Enable/Disable)
(Enable/Disable)
Press key for save & exit
(Under Frequency)
(Under Voltage)
(Over Frequency)
Press key
SET
SET
p a s
1 1
O V
e n b
u V
e n b
O F
e n b
e n b
u F
Password
If over voltage is enable
If under voltage is enable
(Over Voltage )
(Over Voltage value)
(Over Frequency Value)
(Enable/Disable)
(Enable/Disable)
(Enable/Disable)
(Phase Sequence)
(Phase loss)
(Under Frequency value)
(Under Voltage )
(Over Frequency )
(Asymmetry)
p a s
7 3
O V
2 8 0
2 8 0
O F
a s
5 5 0
e n b
e n b
p L
p s
4 S S
U F
e n b
(85-550V For 3Ø-3W )
(50-330V For 3Ø-4W/1Ø-2W )
(Under Voltage Value)
If Over Frequency is Enable
If Under Frequency is Enable
(45.0-65.0 Hz)
If Over
Frequency
is Disable
(Under Frequency )
(45.0-65.0 Hz)
If Under
Frequency
is Disable
IF
A S (Asymmetry )
If Asymmetry is Enable
2 0 (Asymmetry Percentage)
(2 - 30%)
If
Asymmetry
is Disable
or
Press key for save & exit
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
u V
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Relay Settings
If Over
Voltage
is Disable
If Under
Voltage
is Disable
Press key
for 5 sec
Press key
for 5 sec
Enter Password 11
Enter Password 73
SET
SET
Password 11 : To Enable / Disable parameter
(Over Voltage, Under Voltage,over
Frequency,Under Frequency,
Asymmetry,Phass loss, Phase
sequence)
Press key
SET
(85-520V For 3Ø-3W )
(50-300V For 3Ø-4W/1Ø-2W )
IF
3Ø-4W/3Ø-3W Selected
1Ø-2W
Selected
1Ø-2W
Selected
IF
IF
1Ø-2W
Selected
Page -3

Password 37 : To set Power on delay time, Trip delay
Time,Relay Fault Mode.
NOTE :-
FAULT MESSAGE
4 0 0
Scroll
u v 3 2 0
Scroll
O F
5 2.0
Scroll
Over Frequency Fault
Over Frequency
Value=52.0 Hz
◘
◘
U F
A S
P L
P S
◘
◘
◘
◘
◘
◘
L1 L2 L3R
L1 L2 L3R
L1 L2 L3R
L1 L2 L3R
L1 L2 L3R
L1 L2 L3R
Note : LED Status- blinking LED LED on LED off
O V
4 9.5
2 0
Scroll
Scroll
L1 L2 L3R
L1 L2 L3R
L1 L2 L3R
Under Frequency Fault
Asymmentry Voltage
between y & B Phase
L1 - Phase loss
Phase sequence Fault
Under Frequency
Value=49.5 Hz
Asymmentry Percentage
= 20 %
L1 L2 L3R
L1 L2 L3R
L1 L2 L3R
Press key for save & exit
SET
Password
p a s
3 7
P D L (Power On Delay Time)
5(0-99 Sec.)
T D L
R s t
(Trip Delay Time)
(Reset mode)
(Auto Reset/Manual/ZVR Reset)
S
a u t
r C t
5
(0-999 Sec.)
(Recovery time)
R F M
p F M
(Relay Fault Mode)
(Power Fail Fault memory)
O N
y e s
(ON/OFF)
(Yes/No)
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
Press key
SET
SET
Press key
Press key
Press key
Press key
SET
SET
SET
SET
Press key
Press key
Press key
Press key
SET
SET
SET
SET
Enter Password 37
(0 to 99 sec.)
If Auto / ZVR Reset mode select
n t w (Network selection)
3 p 4
(3Ø-3W/3Ø-4W/1Ø-2W )
Press key
SET
Press key
for 5 sec
SET
If Manual
Reset mode
select
- For Hold & Scroll Press key for 3 Sec.
Over Voltage in
V (3Ø-3W) or V
Over Voltage Value=400V
◘
◘
L1L2 L1
(3Ø-4W)
Under Voltage in
V (3Ø-3W) or V
Under Voltage Value=320V
L2L3 L2(3Ø-4W)
Password 73 : Relay Settings
(Over Voltage, Under Voltage,over
Frequency,Under Frequency,
Asymmetry)
SET
+
- If Reset Mode Selected As ZVR (Zero Value Reset),
then the Relay will be reset after Selected Reset time
once the healthy condition achieved OR Zero Value
reached.
- If you select 1 Phase -2 wire network connection, then
Phase sequence and asymmetry parameter will not
appear in parameter setting
Specifications are subject to change, since development is a continuous process,
So for more updated operating information and Support,
Please contact our Helpline: 9081078681/9081078683 or
Email at Ver:191201[email protected]
Page -4