MuxLab 500112 User manual

© MuxLab Inc. 94-000749-A SE-000749-A
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: [phone] Fax: [phone]
Toll Free (North America): [phone]
E-mail: [email protected] URL: www.muxlab.com
Specifications
Environment PoE CCTV IP
Devices PoE CCTV IP cameras with a 10/100Mb/s Ethernet port, using up to
15.4 Watts.
Transmission Transparent to the user
Standard supported Ethernet side:
IEEE 802.3 10BaseT,
IEEE 802.3U 100Base-TX
IEEE 802.3af compatible PoE
PoE Power Class 3
Connectors One (1) BNC 75 Ohms.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
LED Indicators Power, IP Traffic, 100MBps
Maximum Distance RG59/RG6: Up to 980 ft (300m) @ 100Mbps
UTP Cat 5e/6: Up to 330 ft (100 m)
Note: When installed in an electrically noisy environment, an STP cable
must be used. Also, cross-connection reduces the effective distance
depending on the grade of twisted cable used.
RJ45 Pin Configuration
Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straight-
through wiring.
RJ45 Link
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Cable UTP/STP: One (1) Cat 5e/6 or better twisted pair cables required
RG59/RG6: 75 Ohms (avoid CCS cable)
PoE Power Supply
(500113)
Optional PoE Power Supply (110-240V/48VDC/.625A, 2.1mm plug)
with inter-changeable blades (sold separately). Required at the Camera
Side Device when coax cable quality or length results in insufficient
power reaching the camera. Required at the Network Side Device
when used with non-PoE LAN switch.
Power Consumption Network Side: 1.82 Watt Camera Side: 1.73 Watt
Temperature Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Enclosure Metal
Accessories Wall-mount brackets included
Dimensions 4.37” x 2.95” x 0.99” (110 x 75 x 25 mm)
Weight 1.5 lb (0.68 kg)
Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0
Warranty 2 years
Order Information 500112 LongReach CCTV IP PoE Extender Kit
500113 Power Supply for 500112 (48VDC)
LongReach CCTV IP PoE Extender Kit
500112
Quick Installation Guide
Overview
The LongReach CCTV IP PoE Extender Kit (500112) allows one IP camera (15.4
Watts) to be connected up to 980 ft (300 m) via a single 75-ohm coax cable in a point-
to-point configuration. The maximum distance depends on the grade and quality of
coaxial cable. An optional PoE 48VDC Power Supply (500113) is available if required.
Applications
CCTV IP surveillance
Installation
1. Identify the connectors on the Extenders as indicated on the product labels.
2. Attach the surface-mount brackets if required as shown below.
All manuals and user guides at all-guides.com
all-guides.com

© MuxLab Inc. 2013
3. Verify that the distance between the CCTV IP PoE extenders is within MuxLab
specifications (see Specifications table).
4. To install the Network Side Device:
3a. Connect the extender to the PoE Ethernet Switch with a UTP Cable.
Note: If the Ethernet Switch is not PoE; you will need to connect a PoE Power
Supply (500113) to the Network Side Device.
3b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX
LINK connector on the Extender.
5. To install the Camera Side Device:
4a. Connect the extender to the camera with a Cat5e/6 cable.
Note: If the quality or length of the coaxial cable reduces the power to a level that
is insuffiicent to power the camera, you will need to connect a PoE Power Supply
(500113) to the Camera Side device.
4b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX
LINK connector on the Extender.
6. Power on the equipment and verify the image quality. The following is a diagram
of a typical configuration.
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions
in respect to the installation of the CCTV IP PoE Coax Extender Kit:
Network Side
LEDs
Camera Side
LEDs Probable Cause Possible Solutions
Symptom
Power IP Traffic Power IP Traffic
No Image OFF OFF OFF OFF No power • Check if the Ethernet
switch is PoE.
• Check the power
connection.
No Image ON OFF OFF OFF Coaxial Cable • Check the coaxial
cables.
No Image ON OFF OFF OFF Distance • Check the coaxial
cables length and
quality.
No Image ON OFF ON OFF UTP Cable • Check the UTP Cable
pin out.
No Image ON ON ON ON No Traffic • Check network
configuration.
Choppy Image ON BLINK ON BLINK Distance • Check cable length
• Check the coaxial
cable quality.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or ([phone] (International).
All manuals and user guides at all-guides.com