My Weigh iBalance i5500 User manual

1. Selection of auto backlight mode.
Press [UNIT] to select auto backlight function, the display will show an arrow
next to LIGHT , this means auto backlight function active, press [UNIT]
again, the display will not show the arrow next to LIGHT, this means the auto
backlight function is inactive, i.e. shut off backlight function.
2. Selection of auto shut off mode.
Press [ZERO] to select auto shut off function, the display will show an arrow
next to A_OFF, this means auto shut off function active. Press [ZERO] again,
the display will not show an arrow next to A_OFF, this means the auto shut
off function is inactive.
3. Return to weighing mode.
Press[ON/OFF] to turn the power off, press [ON/OFF] again to turn on the
power and the scale will return to normal weighing mode.
* Counting procedures(optional)
1.Press [ON/OFF] to turn on the scale.
Wait for "0" to appear on the display.
2.Start the Count Procedure
If necessary, press [ZERO] key to set the display to “0”.
3. Place a given number of samples of an item on the pan (the Sample Size should
be either 10、20、50 or 100 pieces). The weight of these samples will show on the
display.
4. Press the [UNIT] key several times to put the scale in PCS mode.
5. Select the sample size (the same as you chose above) by pressing the [PCS] key.
(press it as many times as necessary to put it in the correct sample size ,the sample
size is the same as in step three =10、20、50or100.
6. Press the [UNIT] key, the display will show “selected pcs”, then the scale will
remember the sample size you selected and show the starting sample size on the
display
(you can now remove the samples if you want to return the scale to 0)
7. Place the items that you want counted onto the tray and the total number of items
will show on the display.
8. Presses the [UNIT] key to exit the counting function and return to normal
weighing or you can press ON/OFF to turn the scale off to exit .
NOTE: the weight of unit sample > 10e.
i5500 COMPACT SCALE
My Weigh iBalance SERIES
INSTRUCTION MANUAL

SAFETY PRECAUTIONS
All safety messages are identified by the following the words "WARNING" and
"CAUTION". These words mean the following:
△WARNING
Important information to alert you to a
situation that might cause serious injury and
damage to your property if instructions are
not followed.
△CAUTION Important information that tells how to prevent
damage to equipment.
When using the scale/balance, the following safety precautions should always be
followed.
△ WARNING
Use only the AC adaptor with the scale/balance. Other adaptor may cause
damage. (AC adaptor is optional)
△ CAUTION
Avoid installing the scale/balance in direct sunlight, this may cause discoloration or
malfunctions.
Do not mix the type of batteries. Replace all other batteries at the same time.
If the scale/balance is not to be used for a long period of time, remove all batteries
from the battery compartment to avoid leakage which may cause damage to the
instrument.
Avoid overloading that could cause damage to the scale/balance.
Do not drop water in the scale/balance that is not water-resistant. It causes damage,
if inside of the scale/balance is wet.
Matter charged static electricity could influence the weighing. Discharge the static
electricity. As example, the method is to use the electrification prevention spray, to
spray it to both side of weighing platform.
1
SPECIFICATIONS
Model number i5500 Capacity 100g Division 0.005g
Platter / Tray 140×165mm
Net/gross weight 510/620g
Standard carton: 29×22×14(cm3)
Package
12 Units in one box: 60×45×45(cm3)
Operating Temperature 0-40c (32-104℉))
6×AA Size Batteries or AC/AC
Power source
Adapter 11V/150mA (optional)
**SPECIALWARNING**
Cell-Phones, Cordless-Phones, and any radio-frequency device can
cause temporary interference and cause the scale to temporarily not
work properly. Please do not use any electronic device near the i101.
Just like in an Airplane, do not use your cell-phone near the scale
when it is in use. While there is NO risk of permanent damage to
the scale, interference can cause an incorrect calibration or incorrect
weight readings.
FUNCTION SETTINGS
4. Enter function setting mode.
The scale should be OFF. Press and hold [UNIT] first, then press and
release [ON/OFF] (while keeping [UNIT] pressed) the display will show
LIGHT or A_OFF arrow and the display will show 888888 Now you can
release the UNIT key.

6
CALIBRATION
When to calibrate
Calibration may be required when it is initially installed, if the scale/balance is
moved to a substantial distance.
This is necessary because the weight of a mass in one location is not necessarily the
same in another location. Also, with time and use, mechanical deviations may
occur.
How to calibrate
1.Before entering calibration mode, press [ON/OFF] to turn the power on for
1minutes.
2.Enter calibration mode
3.The scale must be powered OFF. Press and hold [ZERO] first, then Press
[ON/OFF] while keeping the [ZERO] button depressed, then release both keys.
The display will show the A/D value (a series of random numbers).
4.Wait for the stable indicator to be displayed, Press [UNIT] the display will show
"00SAVE", then after 2 seconds the display will return to the random A/D value.
5.Place 5000 grams of weight(s) on platform. Wait for the stable indicator to
display, then press [UNIT], the display will show "00SAVE". Calibration is
complete, remove the weight(s).
Turn the scale OFF (Press the ON/OFF key) , then turn it back ON and check some
weight readings. If calibration is still incorrect, repeat calibration but try it more
slowly
FEATURES
zAuto shut off (optional). ●Auto calibration
zAutozerotracking ●Auto backlight (optional)
zLow batter indication ●g/oz/lb/ozt/gn/dwt/ct/n or
zLarge LCD (6digits 15 mm high) g/ct/oz/tl/tola/gn/dwt
zLarge square weighting pan conversion(optional)
zNet weight/stability indication ●with counting function(optional)
z1/30000&1/15000 division available
5
PARTS DESCRIPTION
RIGHT SIDE
AC adaptor
Socket
TOP
Weighing platform
The arch face of platform is front.
Correct the direction of the pan.
Display
ON/OFF key
Turns the scale
power on/off.
PCSkey
UNIT key counting mode
Changes weighing units, g ,oz,lb, ozt, dwt, ct,gn or pcs(counting mode).
ZERO key (for TARE)
ets display to zero or
Subtracts weight of a container.
BOTTOM
Battery compartment
Battery compartment cover
Batteries
Use 6 AA batteries
DISPLAY
STABLE indicator Auto backlight function indicator
Indicates when the reading is stable.
Auto shut off function indicator
ZERO indicator
Indicateswhenthereadingisstable
Weighing unit
Low battery indicator
2

PREPARATION
1.Installing batteries/Connecting theAC adaptor
Batteries
Battery Removethebatterycompartment
compartment coverandinsertsixbatteries(R6P/LR6
/AAsize)intothebatterycompartment,
takingextremecarethatthepolarities
plusandminusisobserved.
R6P/LR6/AA size
Drybatteries.
Battery compartment cover (batteries are not included)
AC adapter (optional)
Plug the AC adapter to the AC
ACadaptor adapter socket on the side.
socket The AC input requirement could
be 110,120,220,230 or 240Volts
(50/60Hz)dependingonthearea
whereused,sopleaseverifythat
theadaptoriscorrect
2.Setting up the scale/balance
△
!CAUTION
Avoid installing the scale/balance in direct sunlight, that may cause discoloration or
malfunctions. Place your scale/balance on a firm weighing table so that the
scale/balance is level. (The scale/balance will not perform accurately when it is not
level.)
Place the scale/balance on the firm surface that is flat and level for an accurate
weighing.
WEIGHING
Before weighing
Whenever possible, please allow the balance to warm up for 10 minutes after first
turning to power on, so that the balance will function. Properly and accurately.
Error messages
EEEE: Overload
: Low battery
Calibration may be required before weighing.
Read "CALIBRATION" first and if necessary, calibrate your scale/balance for
accurate weighing.
Weighing procedures
1.Press [ON/OFF] to turn on the scale/balance.
When power is turned on, all display segments appear on LCD for a few seconds
and finally "0" will appear on the display.
2.Select the weighing unit with [SET].
Press [SET] to select a weighing unit, eg. "g"、" ct " 、" oz "、" dwt "、"ozt"、"gn"、
"n" or "g"、" ct " 、" oz "、" tl "、"tola"、"gn"、"dwt".
Once the unit has been selected, the selected unit will be displayed to the weight
value.
3.Start weighing
If you do not use a container for weighing,
Verify the reading is "0". If not, press [ZERO] to display "0".
Place objects on the weighing platform to weigh.
When the reading becomes stable, the stable indicator is displayed.
If you use a container for weighing,
Place an empty container on the platform.
Wait for the stability indicator to be displayed and press [ZERO].
Place the objects to be weighed in the container.
When the reading becomes stable, the stable indicator is displayed.
4
3