Napoleon Ascent Deep Series User manual

FRENCH PG. 71
W415-2912 / E / 06.02.21
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • www.napoleon.com • [email protected]
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)
NATURAL GAS MODELS:
PROPANE GAS MODELS:
Product Name / Code
(MUST use title from Price Book)
ADD ____ ILLUSTRATED
ADD PRODUCT IMAGE
CSA /
INTERTEK
LOGO
SAFETY INFORMATION
- Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be
performed by a qualified installer, service
agency, or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
WARNING
!
ENGLISH
$10.00
FOR INDOOR USE ONLY
IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD “PLACE
BARCODE LABEL ON THE OWNER’S MANUAL”
D42PTRE / DX42PTRE
INSTALLATION MANUAL
D42NTRE / DX42NTRE
PLACE BARCODE LABEL ON THE
OWNER’S MANUAL
Ascent™ Deep Series
Safety Barrier
(DX42 illustrated)

W415-2912 / E / 06.02.21
EN
2
safety information
• This appliance is hot when operated and
can cause severe burns if contacted.
• Any changes or alterations to this
appliance or its controls can be
dangerous and is prohibited.
• Do not operate appliance before reading and
understanding operating instructions. Failure
to operate appliance according to operating
instructions could cause fire or injury.
• Ensure the glass door is opened or removed
when lighting the pilot for the first time and
when the gas supply has run out.
• Risk of fire or asphyxiation, do not operate
appliance with fixed glass removed and never
obstruct the front opening of the appliance.
• Do not connect 110 volts to the control valve,
with the exception of models; GSST8 and
GT8.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during
installation. Sheet metal edges may be sharp.
• Do not burn wood or other materials in this appliance.
• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing
and operating the appliance.
• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at
test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test
pressures equal to or less than 1/2 psig (35mb).
• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance
to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these
appliances are suitable for 0°F / -18°C.
• Children and adults should be alerted to hazards of high surface temperature and should stay
away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the
appliance. Toddlers, young children and others may be susceptible to accidental contact
burns. A physical barrier is recommended if there are at risk individuals in the house. To
restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from
furniture and draperies.
• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.
• Even after the appliance is off, it will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children
from hot surfaces. These screens and guards must be fastened to the floor.
• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior
to operating the appliance.
• It is imperative that the control compartments, burners and circulating blower and its passageway in the
appliance and venting system are kept clean. The appliance and its venting system should be inspected
before use and at least annually by a qualified service person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and
free from combustible materials, gasoline and other flammable vapors and liquids.
• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it
serviced. Keep burner and control compartment clean.
• Under no circumstances should this appliance be modified.
• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner flame
patterns.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
DANGER
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and must be
installed for the protection of children and other at-risk
individuals.
!WARNING

EN
W415-2912 / E / 06.02.21 3
safety information
!WARNING
• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this
appliance.
• This appliance must not be connected to a chimney flue pipe serving a separate solid fuel burning
appliance.
• Do not use this appliance if any part has been under water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the control system and any gas control which has
been under water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualified service person, if equipped.
• Do not strike or slam shut the appliance glass door, if equipped.
• Only doors / optional fronts certified with the appliance are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your
home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have
it serviced by a qualified technician before operating it again.
• If equipped, the screen must be in place (closed) when the appliance is in operation.
• When equipped with pressure relief doors, they must be kept closed while the appliance is operating
to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of
the exhaust escaping through these openings can also cause the surrounding combustible materials to
overheat and catch fire.
• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the
flu, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working
properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with
heart or lung disease, anemia, those under the influence of alcohol, those at high altitudes are more
affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean
may result in sooting and property damage.
• As with any combustion appliance, we recommend having your appliance regularly inspected and
serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and
your family against Carbon Monoxide (not applicable for outdoor appliances).
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the
appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,
discolouration or damage to decorations, a TV or other electronic components.
• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier
shall be replaced with the manufacturer’s barrier for this appliance.
• Installation and repair should be done by a qualified service person. It is imperative that control
compartments, burners and circulating air passageways of the appliance be kept clean.
• For outdoor products only: this appliance must not be installed indoors or within any structure that
prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.
• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace
only with a fast acting thermocouple supplied by Wolf Steel Ltd.
!
WARNING
!
Disconnect the appliance main gas valve/control
from the supply piping when pressure testing that
system at pressures in excess of 1/2 psi (3.5 kPa).
Isolate the appliance with it’s shut off valve during
any pressure testing of the supply piping at
pressures equal to or less than 1/2 psi (3.5 kPa).
FIRE RISK HAZARD / DELAYED IGNITION
High supply pressure will damage the valve / controls.
Add California Prop 65 warning
!
WARNING:
This product can expose you to chemicals including lead and lead compounds,
which are known to the State of California to cause cancer, and chemicals including carbon
monoxide, which are known to the State of California to cause birth defects or other reproduc-
tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2912 / E / 06.02.21
EN
4
table of contents
1.0 general information 5
1.1 rates and efficiencies 5
1.2 installation checklist 6
1.3 installation overview 7
1.4 rating plate information 9
1.5 mobile home installation 9
1.6 hardware list 10
1.7 dimensions 11
1.8 optional heat management system
(UHM) 12
2.0 venting requirements 13
2.1 typical venting installation 14
2.1.1 corner termination 15
2.2 minimum air terminal location
clearances 16
2.3 top exit - all terminations 17
2.4 rear exit - horizontal termination 18
2.5 rear exit - vertical termination 19
2.6 rear exit 20
2.7 rear exit shield (for rear vent only) 20
2.8 top exit 21
3.0 rough framing 23
3.1 minimum framing dimensions 23
3.2 standoff and standoff shield
installation 25
3.3 minimum clearance to combustible
enclosures 26
4.0 venting installation 30
4.1 horizontal installation 31
4.2 vertical installation 32
4.3 using either flexible vent components 33
4.3.1 horizontal air terminal installation 33
4.3.2 vertical air terminal installation 34
4.3.3 appliance vent connection 34
4.3.4 restricting vertical vents 35
5.0 electrical information 36
5.1 hard wiring connection 36
5.2 receptacle wiring diagram 36
5.3 electronic wiring diagram 36
5.4 battery back-up installation (D42 only) 37
5.5 initializing the transmitter / battery holder
for the first time (DX42 only) 38
5.6 wiring diagram (D42 only) 39
5.7 wiring diagram (DX42 only) 40
6.0 gas installation 41
7.0 nailing tab installation 41
8.0 operation 42
8.1 pilot-on-demand 43
9.0 finish framing 44
9.1 TV recess 44
9.2 non-TV recess 45
10.0 finishing 46
10.1 safety barrier & glass door installation /
removal 46
10.2 finishing with non-combustibles 47
10.3 installing non-combustible board 48
10.4 minimum combustible mantel
clearances 49
10.5 clearances around appliance (TV and
valuable objects) 50
10.6 log placement 51
10.7 glowing embers 53
10.8 charcoal embers 53
11.0 adjustments 54
11.1 venturi adjustment 54
11.3 pilot burner adjustment 55
11.2 flame characteristics 55
12.0 maintenance 56
12.1 care of glass 56
12.2 annual maintenance 57
12.3 glass / door replacement 57
12.4 night light replacement (DX42 only) 58
12.5 blower replacement 58
13.0 replacement parts 59
13.1 D42 overview 60
13.2 D42 valve train assembly 61
13.3 DX42 overview 62
13.4 DX42 valve train assembly 63
13.5 OLKDX42 64
14.0 troubleshooting 65
15.0 warranty 68
The information throughout this manual is believed to be correct at the time of printing. Wolf Steel
Ltd. reserves the right to change or modify any information within this manual at any time without
notice. Changes, other than editorial are denoted by a vertical line in the margin.
note:

EN
W415-2912 / E / 06.02.21 5
standard checklist
1.0 general information
When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of specific recommendations
from the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each
additional 1,000ft (305m). Expansion / contraction noises during heating up and cooling down cycles are normal
and are to be expected.
This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certified for mobile
home installation.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified kit is used.
The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be
improved if the assembly is warmed, using a hair dryer or similar heat source.
This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.
note:
Batteries must be disposed of according to the local laws and regulations. Some batteries may be
recycled, and may be accepted for disposal at your local recycling center. Check with your
municipality for recycling instructions.
1.1 rates and efficiencies
D42 DX42
Fuel Type Natural Gas Propane Natural Gas Propane
Altitude (FT) 0-4,500
Max. Input (BTU/hr) 26,000 31,000 30,000
Min. Inlet Gas Supply Pres-
sure 4.5” w.c. (11mb) 11” w.c. (27mb) 4.5” w.c. (11mb) 11” w.c. (27mb)
Max. Inlet Gas Supply Pres-
sure 7” w.c. (17mb) 13” w.c. (32mb) 7” w.c. (17mb) 13” w.c. (32mb)
Manifold Pressure (Under
Flow Conditions) 3.5” w.c. (9mb) 10” w.c. (25mb) 3.5” w.c. (9mb) 10” w.c. (25mb)
Installer: please fill out appliance
checklist in the owner’s manual
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
appliance and must be installed.
important:
Some components and/or media are packaged separately and must be installed in accordance with the
information in this manual.
*Max. inlet pressure not to exceed 13” w.c. (32mb).

W415-2912 / E / 06.02.21
EN
6
general information
1.2 installation checklist
GAS FIREPLACE INSTALLATION CHECKLIST
Customer: Date Installed:
Address: Installer:
Model: Dealer:
Serial #: Dealer Phone #:
This checklist is a reference tool only. It is not intended as a substitute for the installation instructions.
Wolf Steel Ltd. recommends photographs of the various stages of construction be filed along with a copy of this completed form.
Fireplace Installation
Is the fireplace level and secured?
YES IF NOT, PLEASE EXPLAIN WHY?
Are the factory supplied non-combustible materials installed?
Is the exterior wall insulated and dry-walled?
Are the clearances to combustibles maintained?
Are the logs/media installed as instructed?
Are the accessories installed as instructed?
Is the glass door properly sealed and unobstructed?
Is the safety barrier installed and secure?
Are all required accessories installed (i.e. door trims)?
Venting Installation
Is the venting configuration within the parameters?
Has the venting been sealed with the appropriate sealant?
Is the venting supported and secured?
Are all clearances to combustibles maintained?
Are the appropriate firestops and shields properly installed?
Is the terminal, level, secured and sealed?
Gas and Electrical
Was the fireplace converted to propane?
Was the appropriate supply pressure verified?
Were all gas connections leak tested?
Is the 110 VAC supply connection to the fireplace compliant?
Are all electrical wires protected from damage?
Finishing
Non-combustible materials used as per instructions?
Enclosure instructions forwarded to builder/finisher?
Minimum enclosure dimensions compliant?
Combustible Mantle Clearances compliant?
Commissioning
Was the fireplace test fired and all operation verified?
Safety and lighting instructions reviewed with the Customer?
Operating Instruction Manual left with the Customer?

EN
W415-2912 / E / 06.02.21 7
general information
1.3 installation overview
Recommended installation steps:
1. Determine venting requirements before deciding the final location of the appliance.
2. Install rough framing (refer to “rough framing” section).
3. Place the appliance in its final position.
4. Install nailing tabs (refer to “nailing tab installation” section).
5. Install appliance venting (refer to “venting installation” section).
6. Install all electrical wirings (refer to “electrical information” section).
7. Install gas lines (refer to “gas installation” section).
8. Test appliance.
9. Complete framing (refer to “finish framing” section).
10. Finishing (refer to “finishing” section).
Safety Barrier
10 95
4
6
732
Non-combustible
board

W415-2912 / E / 06.02.21
EN
8
general information
!WARNING
• Always light the pilot whether for the first time or if the gas supply has run out, with the glass door opened
or removed.
• Provide adequate clearance for servicing and operating the appliance.
• Provide adequate ventilation.
• Never obstruct the front opening of the appliance.
• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of
the appliance.
• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is
operating.
• Fire risk. Explosion hazard.
• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test
pressures above 1/2 PISG (35mb). Close the manual shut-off valve before pressure testing gas line at test
pressures equal to or less than 1/2 PISG (35mb).
• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using non-
listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result
in a safety hazard and will void the warranty and certification.
• The appliance must not be operated at temperatures below freezing (32ºF/0ºC). Allow the appliance to
warm to above freezing prior to operation.
THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local
codes. Installation practices vary from region to region and it is important to know the specifics that apply to your area, for
example in the state of Massachusetts:
• This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth of
Massachusetts.
• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas
log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches (0.9m).
• A carbon monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed
combustion product.
The installation must conform with local codes or, in absence of local
codes, the National Gas and Propane Installation Code CSA B149.1
in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54
in the United States. Suitable for mobile home installation if installed
in accordance with the current standard CAN/CSA Z240MH Series,
for gas equipped mobile homes, in Canada or ANSI Z223.1 and
NFPA 54 in the United States.
The appliance and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing
of that system at test pressures in excess of 1/2 psig (35 mb).
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed
with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the
absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National
Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a
properly grounded receptacle. The grounding prong must not be removed from the cord plug.
The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable
and beneficial location for an appliance is in the center of a building, thereby allowing the most efficient use of the heat
created. The location of windows, doors and, the traffic flow in the room where the appliance is to be located should be
considered. If possible, you should choose a location where the vent will pass through the house without cutting a floor or
roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood flooring, the
appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
® (NFI) as NFI Gas
Specialists
www.ncertied.org

EN
W415-2912 / E / 06.02.21 9
general information
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
1.4 rating plate information
The rating plate must remain with the
appliance at all times. It must not be
removed.
note:
1.5 mobile home installation
This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home
Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas
indicated on the rating plate.
This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built
in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base.
Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your
local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must
be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and
the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the
appliance, ensure that the logs are positioned correctly.
This appliance is certified to be installed in an aftermarket permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases, unless a certified kit is used.
Conversion Kits
This appliance is field convertible between Natural Gas (NG) and Propane (P).
To convert from one gas to another, consult your Authorized dealer/distributor.
Certified to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances
Certifié selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation
Direct vent, vented gas fireplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current
standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part
3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance
must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.
Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation
conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,
Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured
Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou
CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.
9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)
WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada
XXXX XXXX XXXX XXXX
MODEL / MODÈLE
Altitude
Input
Reduced Input
P4
Élévation
Alimentation
Alimentation Réduite
P4
Manifold Pressure: 3.5” w.c. (NG)
Minimum Supply Pressure: 4.5” w.c. (NG)
Maximum Supply Pressure: 7”* w.c. (NG)
Pression au Collecteur: 3,5” d’une colonne d’eau (GN)
Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)
Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)
** Maximum inlet pressure not to exceed 13”.
Manifold Pressure: 10” w.c. (P)
Minimum Supply Pressure: 11” w.c. (P)
Maximum Supply Pressure: 13”* w.c. (P)
Pression au Collecteur: 10” d’une colonne d’eau (P)
Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)
Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)
** Pression d’alimentation maximale ne devait pas dépasser 13”.
0-XXXXft (0-XXXXm)
Minimum clearance to combustible materials:
Top, sides & back: per standoff spacers for framing and finishing
materials. For non-combustible framing and finishing materials,
see installation manual.
Top X”
Floor X”
Sides X”
Back X”
Vent top X”
Vent sides & bottom X”
Recessed depth X”
*** Mantel X” from appliance opening
Dégagements minimaux des matériaux combustibles:
Dessus, côtés et arrière: selon les espaceurs de dégagements
pour les matériaux d’ossature selon le manuel du propriétaire
pour les matériaux de finition.
Dessus X”
Plancher X“
Côtés X”
Arrière X“
Dessus du conduit d’évent X”
Côtés et dessous du conduit d’évent X”
Profondeur d’encastré une face X”
*** Tablette X” de l’ouverture de l’appareil
WARNING: Do not add any material to the appliance which will come in contact with the
flames, other than that supplied by the manufacturer with the appliance.
AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien
contact avec les flammes autre que celui qui est fourni avec cet appareil par le fabricant.
*** Maximum horizontal extension:
X”. See installation manual for
greater extensions, minimum vent
lengths and maximum vent lengths.
*** L’extension horizontale maximale: X”.
Référez au manuel d’installation pour des
extensions plus grandes, les longueurs
d’évacuation minimaux et maximum.
The appliance must be vented using the appropriate Napoleon vent kits. See installation
manual for venting specifications. Proper reinstallation and resealing is necessary after servicing
the vent-air intake system.
L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au
manuel d’installation pour les spécifications d’évacuation. Il est nécessaire de bien réinstaller et
resceller l’évacuation après avoir executer l’entretien du système de prise d’air.
Serial Number / N° de Série:
W385-XXXX
REFERENCE# 161746
XXXX
VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF
HEAT, NOT INTENDED FOR USE AS A HEATING
APPLIANCE, NOT FOR USE WITH SOLID FUEL.
APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS
UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE
UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE
CONVIENT PAS AUX COMBUSTIBLES SOLIDES.
FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.
POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE
CERTIFIÉES AVEC L’APPAREIL.
XX,XXX XX,XXX
XX,XXX XX,XXX
For natural gas when equipped with No. XX drill size orifice.
For propane when equipped with No. XX drill size orifice.
Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.
Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.
Electrical rating: 115V, 60HZ. Less than 12 amperes. Spécifications électriques: 115V, 60HZ. Moins de 12 ampère.
XX.X% XX.X%
XXXX XXXX XXXX XXXX
SAMPLE
SAMPLE
pliancesiances
à gaz décoratif à évacuationz décoratif à
talled in accordance with the currentdance with the
and Safety Standard, Title 24 CFR, PartSafety Standard, Title 24 CFR,
ommunitiesmmunities
,
AN
S
I
/
NFPA 501A. This appliance
, ANSI / NFPA 501A. This app
XXX-XXXX. Follow installation instructions.XX-XXXX. Follow installation instruction
ation dans une maison mobile si son installationon dans une maison mobile si son installation
aux Étataux État
s
-
U
n
is
selo
n
la
n
o
rm
e
s-Unis selon la norme
2
4
C
FR
,
Part 3280
,
24 CFR, Part 3280,
r la normela norme
NFPA 501A, Fire Safet
y
Criteria for Manufactured
NFPA 501A, Fire Safety Criteria for Manufactured
ls règlements, selon les codes d’installation ANSI Z223.1 ourèglements, selon les codes d’installation ANSI Z223.1 ou
)
TEEL LTD.
EL LTD.
24 Napoleon Road, Barrie, ON, L424 Napoleon Road, Barrie, ON, L
XXXXXXXX
É
lévation
Élévation
Ali
m
e
nt
a
t
io
n
Alimentation
A
lim
e
nt
a
ti
o
n R
édu
it
eentation Réduite
P
4
P4
M
a
nif
o
l
d
Pr
essu
r
e
:
Manifold Pressure:
10” w.c.
(
P
)10” w.c. (P)
M
inimum
S
upply Pressure:
Minimum Supply Pressure:
11” w.c.
(
P
)11” w.c
M
aximum
S
upply Pressure:
Maximum Supply Pressure:
13”* w.c.
(
P
)13”* w.c
Pression au Collecteur:au Collecteur:
10” d’une colonne d’eau
(
P
)10” d’une colonne d’eau
ession d’Alimentation Min.:ntation Min.:
11” d’une colonne d’eau
(
P
)11” d’une colonne d’eau (P
ression d’Alimentation Max.:ion Max.:
13” * d’une colonne d’eau
(
P
)13” * d’une colonne d’eau (P)
** Pression d’alimentation maximale ne devait pas dépasser 13”.* Pression d’alimentation maximale ne devait pas dépasser 13”.
shinghing
aterials,s,
e openingopening
Dégagements minimaux des matériaux combustibles:Dégagements minimaux des matériaux combustibles:
Dessus, côtés et arrière: selon les espaceurs de dégagementsDessus, côtés et arrière: selon les espaceurs de dégagemen
pour les matériaux d’ossature selon le manuel du propriétpour les matériaux d’ossature selon le manue
pour les matériaux deour les matéria
DessusDessu
Côtés et desst des
Profo
*** Table
horizontal extension:
izontal exten
stallation manual for
on manual
extensions, minimum vent
ons, minim
and maximum vent lengths.
ximum vent lengths.
VENTED DECORATIVE GAS APPLIAVENTED DECORATIVE GAS APPLIA
HEAT, NOT INTENDHEA
APPLIANCE, N
APPAREIL À GAZ DÉCOPPAREIL À
UNE SOURCE DE CNE SOURCE
UTILISÉ COUTILISÉ C
COC
FOR USE WITFOR USE W
POP
ating: 115V, 60HZ. Less than 12 amperes.
115V, 60HZ. Less than 12 amperes.
SpéciSpé
XXXXXXXX
M
CERTIFIEDUNDER/HOMOLOGUESELON LESNORMES: CSA 2.33b - 2008, ANSIZ21.88b- 2008 VENTEDGAS FIREPLACE HEATER/APPAREIL DECHAUFFAGE ALIMENTÉ
AUGAZET VENTILÉ
VENTEDGASFIREPLACE HEATER.APPROVEDFOR BEDROOM, BATHROOMANDBED-SITTING ROOM INSTAL LATION.SUITABLEFORMOBILEHOMEINSTALLATION IFINSTALLED IN ACCORDANCEWITHTHE
CURRENTSTANDARDCAN/CSAZ240MHSERIES GAS EQUIPPEDMOBILE HOMES, INCANADA ORINTHEUNITED STATESTHE MANUFACTURED HOME CONSTRUCTION ANDSAFETYSTANDARD,TITLE 24 CFR,
PART3280.WHENTHISUS STANDARD IS NOTAPPLICABLEUSE THESTA NDARDFORFIRESAFETYCRITERIA FOR MANUFACTUREDHOME INSTA LLATIONS,SITESANDCOMMUNITIES,ANSI/NFPA 501A.
FOYERDE CHAUFFAGEAUGAZAVEC ÉVACUATION.HOMOLOGUÉPOURINSTALLATION DANS UNE CHAMBRE À COUCHER,UNE SALLE DE BAINET UNSTUDIO. APPROPRIÉPOURINSTALLATIONDANSUNE
MAISONMOBILESI SON INSTALLATIONCONFORME AUXEXIGENCESDELANORME CAN/CSAZ240MH SÉRIE DE MAISONS MOBILESÉQUIPÉESAU GAZ,EN VIGUEURA UCANADAOUAUX ÉTATS-UNISDELA
NORMEDESECURITÉ ET DE CONSTRUCTIONDE MAISONS MANUFACTURÉES, TITRE 24CFR,SECTION 3280. DANS LECAS OU CETTENORME D'ÉTATS-UNISNE PEUTÊTRE APPLIQUÉE,SERÉFÉRERA LA NORME
RELATIVEAUCRITÈRE DE MESURES DE SÉCURITÉCONTREL'INCENDIEPOUR LES INSTALLATIONS DANSLESMAISONS MANUFACTURÉS, LES SITESET LES COMMUNAUTÉS, ANSI/NFPA501A.
NOTFOR USEWITH
SOLIDFUEL. FOR USE
WITHGLASSDOORS
CERTIFIEDWITH THIS
UNITONLY.
WARNING
:
DONOTADDANYMATERIAL
TOTHEAPPLIANCE, WHICHWILLCOME
INCONTACT WITHTHE FLAMES, OTHER
THANTHAT SUPPLIEDBY THE
MANUFACTURERWITH THE APPLIANCE.
MINIMUMCLEARANCETO
COMBUSTIBLEMATERIALS:
TOP 0”
FLOOR 0”
RECESSEDDEPTHONE SIDED 23"
RECESSEDDEPTH SEE THRU 13.5”
FRAMING(NOTINCLUDING
FACEMATERIAL)
SIDES0”
VENT 2"
BACK 0”
MANTLE 15"*
TOP,SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS
SEEOWNERSMANUAL
UNCOMBUSTIBLE SOLIDE NE
DOITPAS ÊTRÉUTILISÉAVEC
CETAPPAREIL.UTILISER AVEC
LESPORTESVITRÉES
HOMOLOGUÉESSEULEMENT
AVECCETTEUNITÉ.
AVERTISSEMENT:
N'AJOUTEZPAS A
CETAPPAREILAUCUNMATÉRIAU DEVANT
ENTREREN CONTACTAV ECLESFLAMMES
AUTREQUE CELUI QUI EST FOURNI AVEC
CETAPPAREILPAR LE FABRICANT.
DÉGAGEMENTSMINIMAUX DES
MATÉRIAUXCOMBUSTIBLES:
DESSUS 0”
PROFONDEURD'ENCASTRÉ 25"
PLANCHER 0”
ÉVENT 2"
CÔTES 0”
MANTEAU 15"*
ARRIÉRE 0”
MADEINCANADA /FABRIQUÉAUCANADA
WOLFSTEELLTD.BARRIE,ONTARIO, CANADA
ALTITUDE/ÉLÉVATION
INPUT/ALIMENTATION
REDUCEDINPUT/ALIMENTATIONRÉDUITE
ORIFICE/INJECTEUR
MANIFOLDPRESSURE/
PRESSIONAUCOLLECTEUR
MINIMUMSUPPLYPRESSURE/
PRESSIOND'ALIMENTATIONMINIMALE
MAXIMUMSUPPLYPRESSURE/
PRESSIOND'ALIMENTATIONMAXIMALE
0-4500FT(0-1370M)
30,000BTU/H
23,000BTU/H
#38
3.5"WATERCOLUMN/D'UNECOLONNED'EAU
4.5"WATERCOLUMN/D'UNECOLONNED'EAU
7.0"WATERCOLUMN/D'UNECOLONNED'EAU
0-4500FT(0-1370M)
30,000BTU/H
23,000BTU/H
#53
10"WATERCOLUMN/D'UNE COLONNED'EAU
11"WATERCOLUMN/D'UNECOLONNE D'EAU
13"WATERCOLUMN/D'UNE COLONNE D'EAU
THEAPPLIANCEMUSTBEVENTEDUSINGTHE APPROPRIATE
NAPOLEONVENTKITS.SEEOWNERSINSTALLATIONMANUAL
FORVENTINGSPECIFICS. PROPER REINSTALLATION AND
RESEALINGISNECESSARYAFTERSERV ICINGTHEVENT-AIR
INTAKESYSTEM.
L'APPAREILDOITÉVACUERSESGAZENUTILISANTL'ENSEMBLE
D'ÉVACUATIONPROPREANAPOLEON.RÉFÉRER AUMANUEL
D'INSTALLATIONDEPROPRIÉTAIREPOURL'ÉVACUATION
PRÉCISE.ILESTIMPORTANTDEBIENRÉINSTALLERET
RESCELLERL'ÉVENTAPRÈSAVOIR ASSURÉLEMAINTIENDU
SYSTÉMEDEPRISED'AIR.
CLASSIFICATION:115V 0.82AMP, 60HZ
W385-2007
MODEL NATURALGAS/
GAZNATURAL
LHD50NT
MODELPROPANE
LHD50PT
SERIALNUMBER/NO. DE SÉRIE:LV50
ELECTRICALRATING:11 5V0.82AMP,60HZ
REFERENCE#
W/N16131
*MAXIMUM HORIZONTALEXTENSION /L'EXTENSION
HORIZONTALEMAXIMALE: 2".SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS.
SEEOWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.
DESSUS,COTÉS& ARRIÈRE:SELONLESESPACEURSDEDÉGAGEMENTPOURLESMATÉRIAUXD'OSSATURE
SELONLEMANUELDEPROPRIÉTAIREPOURLESMATÉRIAUXDEFINITION.
*L'EXTENSIONHORIZONTALEMAXIMALE: 2".RÉFÉRERAU MANUEL D'INSTRUCTIONPOURDES EXTENSIONS
PLUSGRANDES.RÉFÉRERAUMANUELD'INSTALLATIONDEPROPRIÉTAIRE.

W415-2912 / E / 06.02.21
EN
10
general information
1.6 hardware list
Ref. # Description Quantity
1 1/4” Hex, 1/2” long sheet metal screw 28
22 1/2” long sheet metal screw 4
31-1/2” Truss screw 4
4Sheet metal screw 14
5Drywall screw 5
6Self-drilling screw 2
75/8” Pan head screw 4
Only fasteners supplied with the appliance will be illustrated.
note:
2
56
1
4
7
3

EN
W415-2912 / E / 06.02.21 11
general information
37 7/16"
952mm
28 1/2"
724mm
41 1/16"
1044mm
23 3/4"
603mm
35"
888mm
5 15/16"
150mm
2 5/16"
58mm
40 1/4"
1022mm
26 13/16"
682mm
15 5/16”
390mm
8"
[203mm]
5"
[127mm]
FRONT VIEW RIGHT SIDE VIEW TOP VIEW
22 1/2"
572mm
1.7 dimensions
Safety
Barrier
GAS INLET

W415-2912 / E / 06.02.21
EN
12
general information
1.8 optional heat management system (UHM)
Napoleon’s Universal Heat Management system is an optional gravity vent kit that allows you to manage the heat
produced by the appliance at and around the fireplace.
We recommend installing the Universal Heat Management kit during the installation of the appliance BEFORE the
gas is installed.
For more information, contact your local authorized dealer.
Reduced mantel
clearances (see
Installation
Manual)
Grill to expel
warm air into the
room
Reduced
temperatures
above fireplace

EN
W415-2912 / E / 06.02.21 13
venting requirements
2.0 venting requirements
!WARNING
• Risk of fire. Maintain specified air space clearances to vent pipe and appliance.
• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly
W010-0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both
vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air
gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each
elbow to ensure this gap is maintained. These spaces must not be removed.
This appliance uses a 5” (127mm) exhaust / 8” (203.2mm) air intake vent pipe system. Refer to the section
applicable to your installation.
For safe and proper operation of the appliance follow the venting instructions exactly. Deviation from the minimum vertical
vent length can create difficulty in burner start-up and/or carboning. Under extreme vent configurations, allow several
minutes (5-15) for the flame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that
pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve
to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is
installed. Use a firestop, vent pipe shield or attic insulation shield when penetrating interior walls, floor or ceiling.
The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for
400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.
Connections made by means of an adaptor at the appliance, as well as the connection at the vent terminal must be sealed.
RTV sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems, ex-
cept for the exhaust vent pipe connection to the appliance flue collar which must be sealed using the black high temperature
sealant Mill Pac.
For all vent systems is strongly recommend for all installations but required when power venting the appliance, that the outer
air intake joints are sealed using either high temperature silicone (RTV) or a suitable aluminum tape that covers each joint in
the vent system entirely around its circumference. This will ensure the best performance in every application and avoids per-
formance or condensation concerns that may occur in “tightly” constructed homes, particularly those in cold climates.
Use only Wolf Steel, Metal-Fab, BDM, Simpson Dura-Vent, or Selkirk Direct Temp venting components. Minimum and
maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air
terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Metal-Fab, BDM, Simpson
Dura-Vent, or Selkirk Direct Temp, follow the installation procedure provided with the venting components or on the website
for your venting supplier.
A starter adaptor must be used with the following vent systems and may be purchased through Wolf Steel or from the
corresponding supplier listed below:
If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the initial
installation.
This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate
constructions, such as a chimney as part of the vent system, is not permitted.
note:
Venting System Manufacturer Starter Adapter
Part Number Supplier Website
SureSeal Metal-Fab 5DNA Wolf Steel www.mtlfab.com
Direct Vent Pro Simpson DuraVent W175-0170 Wolf Steel www.duravent.com
Pro-Form BDM N/A BDM www.dalsinmfg.com
Direct Temp Selkirk 5DT-AAN Selkirk www.selkirkcorp.com
Ventis Olympia Chimney
and Venting VDV-NA05-58F Olympia Chimney and Venting www.olympiachimney.com
When using Wolf Steel venting components, use only approved Wolf Steel rigid / flexible components with the following ter-
mination kits: wall terminal kit GD422-1, GD422R-2, ST58U-1 or 1/12 to 7/12 pitch roof terminal kit GD410, 8/12 to 12/12
roof terminal kit GD411, flat roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With flexible
venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) vent kit
GD430.

W415-2912 / E / 06.02.21
EN
14
venting requirements
Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended
that all horizontal runs have a minimum 1/4” (21mm) rise per foot/meter using flexible venting. For safe and proper
operation of the appliance, follow the venting instructions exactly.
A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single fam-
ily dwellings and serves both dwellings. Local codes or regulations may require different clearances.
Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼”
(31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.
This appliance is certified for use with a power vent kit. Contact your local authorized dealer for more information.
2.1 typical venting installation
12"
(30.5cm)
minimum
to grade
Special vent installation (periscope termination)
Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when
final grading is completed, the bottom air slot is located a minimum 12” (30.5cm) above grade. The maximum
allowable vent length is 10’ (3m) for a fireplace and 8’ (2m) for a stove.
base of air collar
base of air collar
TOP VENT REAR VENT
TOP VENT
20” (51.8cm)
Maximum
13” (33cm)
Minimum
50”
(127cm)
Minimum plus
rise*
20” (50.8cm)
Maximum
28 1/2” (72.4cm)
Minimum plus rise*
30” (76.2cm)
Minimum
*See “venting requirements” and “venting
installation” sections.
For optimum flame appearance and appliance performance, keep the vent length and number of elbows to a minimum.
The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that
it is unobstructed and undamaged.
Rigid and flexible venting systems must not be combined. Different venting manufacturer components must not
be combined.
These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20
feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two
horizontally or three vertically (excluding the appliance and the air terminal connections) when using flexible venting.
All vent measurements start at the base of the air collar of the appliance.

EN
W415-2912 / E / 06.02.21 15
venting requirements
16" (40.6cm)
minimum
40 FT (12M)
maximum
3 FT (1M)
minimum
base of air collar
20” (50.8cm)
MAXIMUM
6” (152mm)
RISE MINIMUM
2.1.1 corner termination
The maximum vent length for a corner installation is 20" (50.8cm) of horizontal run, in addition to the 45°
offset. Using rigid venting, zero rise is acceptable. Using flexible venting, it is required to maintain a 6"(152mm)
rise. See illustrations below.
FLEX VENTING RIGID VENTING

W415-2912 / E / 06.02.21
EN
16
venting requirements
2.2 minimum air terminal location clearances
QMIN RMAX MAX
R
= 3 feet
(0.9m) = 2 x IHHW
(4.6m)
QACTUAL
INSTALLATIONS
CANADA U.S.A.
A12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.
B12” (30.5cm)Δ9” (229mm) ΔClearance to windows or doors that open.
C12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.
D18”
(45.7cm)**
18”
(45.7cm)**
Vertical clearance to ventilated soffits located above the terminal within a horizontal distance of 2’ (0.6m)
from the center line of the terminal.
E12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated soffit.
F0” (0mm) 0” (0mm) Clearance to an outside corner wall.
G0” (0mm)*** 0” (0mm)*** Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).
2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).
H3’(0.9m) 3’(0.9m)**** Clearance to each side of the center line extended above the meter / regulator assembly to a maximum
vertical distance of 15’ (4.6m).
I3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.
J12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.
K6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.
L7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.
M12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch, deck or overhang.
N16” (40.6cm) 16” (40.6cm) Clearance above the roof.
O2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.
P8’ (2.4m) 8’ (2.4m) Roof must be non-combustible without openings.
Q3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.
R6’ (1.8m) 6’ (1.8m) See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening
between the terminal and the open side of the structure.
S12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony
Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.
* Recommended to prevent condensation on windows and thermal breakage
** It is recommended to use a heat shield and to maximize the distance to vinyl clad soffits.
*** The periscope requires a minimum 18 inches clearance from an inside corner.
**** This is a recommended distance. For additional requirements, check local codes.
† 3 feet above if within 10 feet horizontally.
‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.
†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the floor.
†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.
††* Permitted only if the balcony is fully open on a minimum of one side.
Wall terminals are for illustration purposes only. Size and shapes may vary. Wall terminal
measurements taken from the exhaust outlet, not the mounting plate.
Covered balcony applications ††*
R
QS
GP
Clearances are to be in accordance with local
installation codes and the requirements of the gas
supplier. In their absence, clearances are to be as
listed above and are based on national codes.
note:
note:

EN
W415-2912 / E / 06.02.21 17
venting requirements
2.3 top exit - all terminations
0’
0’
Base of
air collar 10’
10’
15’
15’
20’ 25’
20’
30’
40’
5’
1’ 8”
(20”)
1’ 1” min.
(13”)
5’
1 elbow zone
1-2 elbow zone
1-3 elbow zone
1-4 elbow zone
1-5 elbow zone
1-6 elbow zone
H
V
V+H ≤ 40 ft. (For longer vent runs, a power
vent is required).
H ≤ 20 ft.
V + H are measured from the centre of vent
elbows. Elbows are considered as 90º.
Two 45º elbows = One 90º elbow.
3’ min.
(36”)
38 1/2’
(462”)
Vertical termination only.
No horizontal termination allowed.

W415-2912 / E / 06.02.21
EN
18
venting requirements
2.4 rear exit - horizontal termination
0’
0’ 10’
10’
15’
15’
20’ 25’
20’
30’
40’
5’
1 1/2’
(18”)
1 1/2’
(18”)
35 3/4’
(429”)
5’
1-2 elbow zone
1-3 elbow zone
1-4 elbow zone
H
V
(For vent runs that exceed the graph
parameters, a power vent is required).
V + H are measured from the centre of vent
elbows. Elbows are considered as 90º.
Two 45º elbows = One 90º elbow.
4 3/4’
(57”)
17 1/4’
(207.6”)
1-5 elbow zone

EN
W415-2912 / E / 06.02.21 19
venting requirements
2.5 rear exit - vertical termination
10’
10’
15’
15’
20’
25’
20’
30’
40’
5’
39’
(468”)
1 elbow zone
1-2 elbow zone
1-3 elbow zone
H
V
(For vent runs that exceed the graph
parameters, a power vent is required).
V + H are measured from the centre of vent
elbows. Elbows are considered as 90º.
Two 45º elbows = One 90º elbow.
0’
0’
1’
(12”)
3
(36”)
5’
4 3/4’
(57”)
1-4 elbow zone
1-5 elbow zone
1-6 elbow zone

W415-2912 / E / 06.02.21
EN
20
venting requirements
2.6 rear exit
A. Remove the safety barrier and glass front (see "safety barrier & door removal / installation" section).
B. Remove the contents from the log box and set aside. You will need the exhaust flue collar and the gasket
(supplied).
C. Remove the outer coverplate and gasket from the back of the outer shell and
secure it to the outer top. Ensure the two pieces of insulation are installed
inside the top air housing.
D. Place the gasket (provided) over the 5" (127mm) flue collar assembly and bend
along perforation.
E. From inside the firebox, insert the 5" (127mm) flue collar through the back of
the firebox. Install the rear exit shield onto the 5" (127mm) flue collar (see "rear
exit shield (for rear vent only)" section).
F. Secure the flue collar assembly, gasket and rear exit shield using
the 10 hex head 3/4" black screws (Fig. 1).
G. Install the 8” (203mm) gasket and collar assembly using 4 pan
head screws (supplied) (Fig. 2).
Fig. 1
2.7 rear exit shield (for rear vent only)
A. Loosen the two screws,
that secure the exhaust plate, and
slide the rear exit shield in place
by sliding its slotted openings
behind the screwheads, tighten
the two previously loosened
screws. Refer to the illustration.
B. Reinstall the door and
safety barrier assembly on the
appliance (see “safety barrier
& door removal / installation”
section).
!WARNING
• Failure to create a seal to the firebox with the exhaust collar assembly will cause the appliance to function
improperly and can cause injury or property damage.
Do not overtighten. The gasket needs only to be snug
against the firebox.
note:
This shield is used to block the
view through the venting to the
outdoors.
note:
This appliance has been factory shipped as a top vent.
note:
Rear exit
shield
5” FLUE
COLLAR
ASSEMBLY
GASKET
Fig. 2
8” INTAKE COLLAR
GASKET
#4 X 10 #7 X 4