Napoleon High Country 6000 Series User manual

W415-1501 / E / 12.17.18
FRENCH PG. 51
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • www.napoleon.com • [email protected]
ADD SAFETY STANDARD INFORMATION
& EPA QUALIFICATION (IF APPLICABLE)
Product Name / Code
(MUST use title from Price Book)
ADD ____ ILLUSTRATED
ADD PRODUCT IMAGE
CSA / OMNI
/ INTERTEK
LOGO
SAFETY INFORMATION
- This heater can be very hot when burning.
- Combustible materials such as firewood, wet clothing, etc. placed
too close can catch fire.
- Children and pets must be kept from touching the heater when it is
hot.
- The chimney must be sound and free of cracks. Before installing this
appliance, contact the local building or fire authority and follow their
guidelines.
- Always operate this appliance with the door(s) or screen (where
applicable) tightly closed.
- Burn wood behind the log retainer directly on the firebricks.
- Do not use an elevated grate or otherwise raise the fire.
- This appliance is designed to burn natural wood only. Higher
efficiencies and lower emissions generally result when burning air
dried seasoned hardwoods, as compared to softwoods or to green
or freshly cut hardwoods.
- Do not start a fire with chemicals or fluids such as gasoline, engine
oil, etc.
- Do not burn trash or garbage, lawn clippings/waste, rubber,
waste petroleum products, paints or paint thinners/solvents, plastic,
materials containing asbestos, construction debris, railroad ties or
treated wood, manure or animal remains, salt water driftwood or
salted materials, unseasoned wood, coal, charcoal, coloured papeer,
cardboard, plywood or particleboard. Burning these materials may
result in release of toxic fumes or render the appliance ineffective and
cause smoke.
- Do not let the appliance become hot enough for any part to glow
red.
If the information in these instructions are not followed exactly, a fire
or explosion may result causing property damage, personal injury or
death. Please read the entire manual before you install and use your
appliance. This heeater has not been tested with an unvented gas log
set. To reduce risk of fire or injury, do not install an unvented gas log
set into the heater.
WARNING
!
ENGLISH
$10.00
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
FOR INDOOR USE ONLY
This wood appliance needs periodic inspection and repair. It is against United States federal regulations to operate this wood
appliance in a manner inconsistent with the operating instructions in this manual.
Wood Stoves ONLY
- At least 14 squares inches (90.3 square centimeters) of outside air
must be admitted to the room or directly to the appliance through a
4” (101.6mm) diameter pipe.
- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C).
Attempts to achieve heat output rates that exceed design
specifications can result in steel distortion and damage. IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD “PLACE
BARCODE LABEL ON THE OWNER’S MANUAL”
INSTALLATION AND
OPERATION MANUAL
THIS APPLIANCE HAS BEEN TESTED AND LISTED BY INTERTEK TESTING
SERVICES LTD. AS PER THE STANDARDS: ULC S610, UL 127 FOR
FACTORY BUILT FIREPLACES.
HIGH COUNTRY™ 6000
(NZ6000-1 Illustrated)
Low Mass Appliance

W415-1501 / E / 12.17.18
EN
2
safety information
• This appliance is hot when operated and can cause
severe burns if contacted.
• Any changes or alterations to this appliance or its
controls can be dangerous and is prohibited.
• Do not operate appliance before reading and
understanding operating instructions. Failure
to operate appliance according to operating
instructions could cause fire or injury.
• Before installing this appliance, contact the local
building or fire authority and follow their guidelines.
• This appliance must be installed by a qualified
installer. Never try to repair or replace any part of the appliance unless instructions are given in this manual.
All other work should be done by a trained technician.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not operate without fully assembling all components. Do not install damaged, incomplete or substitute
components.
• Do not let the appliance become hot enough for any part to glow red.
• Risk of cuts and abrasions. Wear protective gloves, footwear and safety glasses during installation. Sheet
metal edges may be sharp.
• All wiring should be done by a qualified electrician and shall be in compliance with local codes. in the
absence of local codes, use the current CSA22.1 Canadian Electric Code in Canada or the current
National Electric Code ANSI/NFPA No. 70 in the United States.
• If equipped, burning your appliance with the ash dump door ajar creates a fire hazard that may result in
discolouration to the door, internal damage to the appliance or a house and/or chimney fire.
• Do not connect this appliance to a chimney flue serving another appliance.
• Clothing or other flammable material should not be placed on or near the appliance. Objects placed in
front of the appliance must be kept a minimum of 48” (121.9cm) away from the front face of the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and
draperies.
• Even after the appliance is off, it will remain hot for an extended period of time.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe servicing a separate solid fuel burning
appliance.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• Only doors / optional fronts certified with the appliance are to be installed on the appliance.
• If the appliance is not properly installed, a house fire may result. Do not expose the appliance to the
elements (ex. rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when
the appliance is used.
• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as
required.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to
avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot
surfaces.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from
hot surfaces. These screens and guards must be fastened to the floor.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with
all plastic bags, these are not toys and should be kept away from children and infants.
• Do not start a fire with chemicals or fluids such as
g
asoline, en
g
ine oil, etc.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING
!WARNING

W415-1501 / E / 12.17.18
EN
3
safety information
Do not use makeshift compromises during installation.
Do not block or restrict air, grille or louvre openings! Do
not add a hood.
Burning your appliance with the door open or ajar cre-
ates a fire hazard that may result in a house and/or
chimney fire.
All venting connections must be in compliance with the chimney manufacturers installation instructions.
Clearances referred to throughout this manual are the minimum requirements.
Your appliance must be installed in accordance with all national and local building code standards and
the standard of Chimney and Appliances, Vents and Solid Fuel Burning Appliances NFPA #211. Consult
the authority having jurisdiction (such as municipal building department, fire department, fire prevention
bureau, etc.) to determine the need to obtain a permit. If you are in doubt about the proper installation for
your situation, contact your dealer or local building or fire official. The manufacturer does not guarantee
that this appliance and its options will completely heat your entire home.
Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.
It is recommended that in all cases, the appliance be secured to the floor. Use the pallet packing brackets
to accomplish this.
!WARNING
• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke
spillage in your home.
• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well
away from the home or structure until completely cool.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage
to decorations, a TV or other electronic components.
For wood appliances:
• Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods
or too green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote
accumulation. When this is ignited it can cause a chimney fire that may result in a serious house fire.
• This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings /
waste, rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing
asbestos, construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood
or salted materials, unseasoned wood, coal, charcoal, coloured paper, gift wrapping, cardboard, plywood or
particleboard. Burning these materials may result in release of toxic fumes or render the appliance ineffective
and cause smoke.
• Burn wood directly on the firebricks. Do not elevate grate or otherwise raise the fire.
• Do not store wood within appliance installation clearances or within the space required for re-fueling and
ash removal.
• If equipped, the catalyst must be installed and in good working order. It is recommended that the catalyst
is inspected at least three times per heating season.
Add California Prop 65 warning
!
WARNING:
This product can expose you to chemicals including lead and lead compounds,
which are known to the State of California to cause cancer, and chemicals including carbon
monoxide, which are known to the State of California to cause birth defects or other reproduc-
tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-1501 / E / 12.17.18
EN
4
table of contents
1.0 dimensions 5
2.0 general information 6
2.1 general instructions 6
2.2 features 7
2.3 this cordwood fuel appliance 7
2.4 electrical specifications 7
2.5 packing list 7
2.6 rating plate information 8
3.0 installation overview 9
4.0 installation planning 10
4.1 location and clearances 10
4.2 ventilation openings 11
4.3 outside combustion air 11
4.4 floor protection 12
4.4.1 ember strip and hearth extensions 12
4.4.2 hearth extension 13
4.4.3 hearth examples 14
5.0 installation 15
5.1 chimney 15
5.2 typical chimney installation 16
5.3 adding chimney sections 17
5.4 offset chimney installation 18
5.5 installing flashing and storm collar 19
5.6 connection to a masonry chimney 19
5.7 air cooled chimney installation 20
6.0 framing 21
6.1 when using a solid pack chimney 22
6.2 when using an air cooled chimney 22
6.3 minimum clearance to combustibles23
6.4 minimum enclosure clearances 23
6.5 minimum mantel clearances 24
7.0 finishing 25
7.1 faceplate 25
7.2 upper grill installation 25
7.3 keystone installation 25
7.4 door handle installation 26
7.5 door installation 26
7.6 door latch installation 27
7.7 secondary air tube removal /
installation 27
7.8 firebrick and baffle installation 28
7.9 optional NZ64 blower installation 29
7.10 NZ150-KT kit 31
7.11 NSK6 optional screen kit 31
7.12 smoke shelf 32
8.0 selecting wood 33
9.0 operation 34
9.1 operating sounds and smells 34
9.2 fire extinguishers, smoke detectors
and carbon monoxide detectors 34
9.3 establishing draft 35
9.4 fuel loading and burn cycle 36
9.5 starting the fire 37
9.6 smoking 39
10.0 maintenance 40
10.1 ash removal procedures 40
10.2 creosote formation and removal 40
10.3 run-away or chimney fire 41
10.4 chimney cleaning 41
10.5 glass and gasket replacement 42
10.6 care of glass 42
10.7 NZ64 blower replacement 43
11.0 replacement parts 44
11.1 overview 45
12.0 accessories 46
13.0 troubleshooting 47
14.0 warranty 48
15.0 service history 49
Changes, other than editorial, are denoted by a vertical line in the margin.
note:

W415-1501 / E / 12.17.18
EN
5
1.0 dimensions
44 15/16" 1141mm
49 1/16" 1246mm
50 1/8"
1273mm
24 3/16"
614mm
8 7/16"
214mm
4 1/4"
108mm
27 3/16" 690mm
25 1/8" 638mm
1 3/8"
36mm
49 1/16" 1246mm
14 7/8"
378mm
24 1/2" 623mm
front view right side view
top view

W415-1501 / E / 12.17.18
EN
6
2.0 general information
2.1 general instructions
Do not install an appliance insert or other products/accessories not specified for use with this appliance.
note:
!WARNING
• Before installing this appliance, contact the local building or fire authority and follow their guidelines.
• This appliance must be installed by a qualified installer. Follow the installation directions. Do not operate
without fully assembling all components.
• If this appliance is not properly installed, a house fire may result.
• Do not expose the appliance to the elements (ex. rain, etc.) and keep the appliance dry at all times. Wet
insulation will produce an odour when the appliance is used.
• This appliance is hot when operated and can cause severe burns if contacted. Children and pets must be
kept from touching the appliance when it is hot. Contact your local authorized dealer/distributor for safety
screens that may be available for this product.
• Combustible material such as firewood, wet clothing, etc. placed too close can catch fire. Objects placed
in front of the appliance must be kept a minimum of 48" (121.9cm) from the front of the appliance.
• All wiring should be done by a qualified electrician and shall be in compliance with local codes and with
the national electric code ANSI/NF No. 70-current (in the United States), or with the current CSA C22.1
Canadian Electric Code (in Canada).
1
2
3
4
4
5
5
5
1. Combustion and dilution air is brought into
the appliance through the fresh air intake col-
lars located on the bottom front sides of the
appliance.
2. The combustion air is brought into the firebox
through many small holes in the airwash
located at the top and sides of the opening.
3. The dilution air is introduced high in the fire-
box above the baffle to cool the chimney.
4. Inside the firebox combustion takes place
and exhausts out the chimney.
5. The optional blower can be installed to draw
fresh outside air into the home (not recom-
mended in colder climates), then either the
NZ150-KT kit or the NZ64 blower can be
installed inside and will circulate the air into
your home.
There are many other appliances in the home competing with this appliance for air, such as kitchen range hoods,
forced air heating devices, and bathroom exhaust fans. Therefore, in order to avoid fire hazards and/or injuries, be
sure to provide sufficient combustion air to this appliance.

W415-1501 / E / 12.17.18
EN
7
general information
2.2 features
• Maximum log length of 32" (81.3cm)
• Optional 320 CFM blower for convection heat
• Thermostat for automatic control of the blower
• Flue outlet diameter 8" (203.2mm)
• Max fuel load 40lbs (18kg)
• Large doors for maximum visibility
• Firebrick lining for firebox protection
• Outside air for combustion
2.3 this cordwood fuel appliance
!WARNING
• Do not let the appliance become hot enough for any part to glow red.
This appliance is a decorative product and not intended as a primary heat source.
Approximate heating capacity up to 1,000 square feet (92 square meters).
2.4 electrical specifications
The blower on "HIGH" draws 2.2 amps on 120 volts A.C. (approximately 250 watts).
2.5 packing list
Shipped with appliance: Shipped with faceplate:
Installation manual Faceplate
Baffle 12 faceplate screws
Ember Strip
Log Retainer Shipped with the door(s):
Flex duct w/ start collar 10' (3m) length, 6" (152mm) Installation instructions and hardware
diameter (1 for NZ150-KT or blower kit and 2 for
outside combustion air supplies).

W415-1501 / E / 12.17.18
EN
8
general information
2.6 rating plate information
Rating plate is located behind the appliance face-
plate.
This illustration is for reference only. Refer to the rat-
ing plate on the appliance for accurate information.
RATING
PLATE
LOCATION
FACEPLATE
note:
The rating plate must remain with the appli-
ance at all times. It must not be removed.
*POUR PLUS D'INFORMATIONS, CONSULTEZ LE MANUEL
D'INSTRUCTIONS DU FABRICANT.
*FOR FURTHER INFORMATION SEE THE MANUFACTURER'S
INSTALLATION AND OPERATING MANUAL.
BACK
0"(0 mm) TO STAND-OFFS
HEADER
96"(2.44 m) FROM BASE OF UNIT
CHIMNEY 2"(51 mm) REFER TO MANUFACTURER'S
INSTALLATION INSTRUCTIONS.
MANTEL
12"(305 mm) TO TOP EDGE OF FACEPLATE
TOP FACING
96"(2.44 m) FROM BASE OF UNIT
SIDE FACING
6"(153 mm) FROM SIDE OF UNIT
ADJACENT SIDEWALL
21"(534 mm) TO EDGE OF FACEPLATE
HEARTH PROTECTION
21"(534 mm) FROM FRONT OF UNIT
HEARTH PROTECTION
8"(203 mm) FROM SIDES OF UNIT
*TOP OF UNIT
(ENCLOSURE CEILING)
120"(3.05 m) FROM BASE OF UNIT
ARRIÈRE 0"(0 mm) AUX ESPACEURS
LINTEAU 96"(2.44 m) DE LA BASE DE L'APPAREIL
CHEMINÉE 2"(51 mm) RÉFÉREZ-VOUS AU MANUEL
D'INSTRUCTIONS DU FABRICANT.
TABLETTE 12"(305 mm) DU HAUT DE LA FAÇADE
DESSUS 96"(2.44 m) DE LA BASE DE L'APPAREIL
CÔTÉ 6"(153 mm) DU CÔTÉ DE L'APPAREIL
MUR LATÉRALADJACENT 21"(534 mm) DU BORD DE LA FAÇADE
PROTECTION DE PLANCHER 21"(534 mm) DU DEVANT DU FOYER
PROTECTION DE PLANCHER 8"(203 mm) DES CÔTÉS DU FOYER
*HAUT DE L'APPAREIL 120"(3.05 m) DE LA BASE DE L'APPAREIL
(PLAFOND DE L'ENCLAVE)
INSULATED CHIMNEY MINIMUM CLEARANCES TO
COMBUSTIBLES:
DÉGAGEMENTS MINIMAUX DE LA CHEMINÉE PRÉFABRIQUÉE
STANDARD AUX MATÉRIAUX COMBUSTIBLES
DÉGAGEMENTS MINIMAUX DE LA CHEMINÉE REFROIDIE À L'AIR AUX MATÉRIAUX COMBUSTIBLES
Face and enclosure
ceiling metal studs, both
clad with cement board
Face must have a
minimum 8' height
of cement board
Cement board and steel studs
Cement board from
the side of the unit
to combustibles
facing and wood
framing may start
at 96" above the
base of the unit
Metal Studs
AIR COOLED CHIMNEY MINIMUM CLEARANCES TO COMBUSTIBLES:
Face metal studs,
clad with cement board
Face must have a
minimum 7' height
of cement board
Minimum
enclosure ceiling
height 7'
6"
Cement board from
the side of the unit
to combustibles
combustible
facing and wood
framing may start
at 84" above the
base of the unit
Cement board Metal Studs
*POUR PLUS D'INFORMATIONS, CONSULTEZ LE
MANUEL D'INSTRUCTIONS DU FABRICANT.
STARTER COLLAR NZAC-KT MUST BE USED IN CONJUNCTION WITH
FMI 8DM AIR COOLED CHIMNEY
CHIMNEY REQUIREMENTS
*FOR FURTHER INFORMATION SEE THE MANUFACTURER'S
INSTALLATION AND OPERATING MANUAL.
BACK
0"(0 mm) TO STAND-OFFS
HEADER
72"(2.83 m) FROM BASE OF UNIT
CHIMNEY
2"(51 mm) REFER TO MANUFACTURER'S
INSTALLATION INSTRUCTIONS.
MANTEL
12"(305 mm) TO TOP EDGE OF FACEPLATE
TOP FACING
84"(3.31 m) FROM BASE OF UNIT
SIDE FACING
6"(153 mm) FROM SIDE OF UNIT
ADJACENT SIDEWALL
21"(534 mm) TO EDGE OF FACEPLATE
HEARTH PROTECTION
21"(534 mm) FROM FRONT OF UNIT
HEARTH PROTECTION
8"(203 mm) FROM SIDES OF UNIT
*TOP OF UNIT
(ENCLOSURE CEILING)
84"(3.31 m) FROM BASE OF UNIT
ARRIÈRE 0"(0 mm) AUX ESPACEURS
LINTEAU 72"(2.83 m) DE LA BASE DE L'APPAREIL
CHEMINÉE 2"(51 mm) RÉFÉREZ-VOUS AU MANUEL
D'INSTRUCTIONS DU FABRICANT.
TABLETTE 12"(305 mm) DU HAUT DE LA FAÇADE
DESSUS 84"(3.31 m) DE LA BASE DE L'APPAREIL
CÔTÉ 6"(153 mm) DU CÔTÉ DE L'APPAREIL
MUR LATÉRALADJACENT 21"(534 mm) DU BORD DE LA FAÇADE
PROTECTION DE PLANCHER 21"(534 mm) DU DEVANT DU FOYER
PROTECTION DE PLANCHER 8"(203 mm) DES CÔTÉS DU FOYER
*HAUT DE L'APPAREIL 84"(3.31 m) DE LA BASE DE L'APPAREIL
(PLAFOND DE L'ENCLAVE)
LE COLLET DE DÉPART NZAC-KT DOIT ÊTRE UTILISÉ
CONJOINTEMENT AVEC LA CHEMINÉE REFROIDIE À L'AIR FMI 8DM
SPÉCIFICATIONS POUR LA CHEMINÉE
Montants d'acier de façade
recouverts de panneaux de ciment
La façade doit posséder
un panneau de ciment
d'une hauteur
minimale de 7'
Hauteur minimale
du plafond de
l'enclave de 7'
6"
Panneau de ciment
sur le côté de
l'appareil aux matériaux
combustibles
La façade combustible
et la charpente de bois
peuvent débuter à 84"
au-dessus de la base
de l'appareil
Panneau de ciment Montants d'acier
Montants d'acier de façade
et de plafond de l'enclave
recouverts de panneaux de ciment
La façade doit posséder un
panneau de ciment d'une
hauteur minimale de 8'
Panneau de ciment et montants
d'acier sur le plafond de l'enclave
non requis à plus de 10'
Hauteur minimale
du plafond de
l'enclave de 7' à 10'
6"
Panneau de ciment
sur le côté de
l'appareil aux matériaux
combustibles
La façade combustible et la
charpente de bois peuvent
débuter à 96" au-dessus
de la base de l'appareil
Panneaux de ciment Montants d'acier
DO NOT REMOVE THIS LABEL
NE RETIREZ PAS CETTE PLAQUE
W385-2065 / D
MODEL/ NO° DE MODÈLE
LISTED FACTORY BUILT FIREPLACE /
SERIAL NO.
NZ6000-1
POUR INSTALLATION ET UTILISATION CONFORMÉMENT AUX MANUEL D'INSTRUCTIONS DU FABRICANT.
RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES DU BÂTIMENT OU DU SERVICE DES INCENDIES AU
SUJET DES RESTRICTIONS ET DES INSPECTIONS D'INSTALLATION DANS VOTRE RÉGION. NE PAS
RACCORDER À LA CHEMINÉE D'UN AUTRE APPAREIL.
CERTIFIED TO / CERTIFIÉ SELON: ULC S610, UL-127
FOYER PRÉFABRIQUÉ HOMOLOGUÉ
COMPOSANTS REQUIS POUR L'INSTALLATION:
EXIGENCES POUR LA CHEMINÉE (voir le manuel d'instructions)
La cheminée doit être certifiée selon l'une des normes suivantes : ULC S610 ou ULC S629
pour le Canada ou selon les normes UL 103HT ou UL-127 pour les États-Unis
Installation dans une cheminée en maçonnerie : La gaine en acier inoxydable doit être
certifiée selon les normes ULC S640 M92 ou ULC 639 pour le Canada ou selon la norme
UL 1777 pour les États-Unis
Cheminée refroidie à l'air : Utilisez seulement FMI 8DM
COMPONENTS REQUIRED FOR INSTALLATION:
CHIMNEY REQUIREMENTS (see installation manual):
SHIPPED WITH THE FIREPLACE:
INSTALLATION MANUAL
BAFFLE
EMBER STRIP
LOG RETAINER
FLEX DUCT W/ START COLLAR 10' LENGTH,
6" DIA (FOR BLOWER AND OUTSIDE AIR
SUPPLY).
SHIPPED WITH FACEPLATE:
FACEPLATE
12 FACEPLATE SCREWS
SHIPPED WITH THE DOOR(S):
INSTALLATION INSTRUCTIONS AND
HARDWARE
Chimney must be certified to one of the following standards ULC S604, ULC S610
or ULC S629 for Canada or UL 103HT or UL-127 for the United States
Masonry chimney installation: Stainless steel liner must be certified to ULC S640
M92 or ULC 639 for Canada or UL 1777 for the United States
Air cooled chimney: Use only FMI 8DM
LIVRÉ AVEC LE FOYER
MANUEL D'INSTRUCTIONS
DÉFLECTEUR
PARE-BRAISES
PARE-BÛCHES
GAINE FLEXIBLE AVEC COLLET DE RACCORD
DE PRISE D'AIR DE 10', 6" DE DIAMÈTRE
(POUR LA SOUFFLERIE ET
L'APPROVISIONNEMENT EN AIR EXTÉRIEUR)
LIVRÉ AVEC LA FAÇADE :
FAÇADE
12 VIS POUR LA FAÇADE
LIVRÉ AVEC LA/LES PORTE(S) :
INSTRUCTIONS D'INSTALLATION
ET QUINCAILLERIE
W385-2065 / D
PREVENT CREOSOTE FIRE: INSPECT
CHIMNEY AND CHIMNEY CONNECTOR, IF
APPLICABLE, TWICE MONTHLY AND CLEAN
IF NECESSARY.
DO NOT OVERFIRE: IF EXTERIOR OF UNIT
GLOWS RED, YOU ARE OVERFIRING.
KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS A
CONSIDERABLE DISTANCE AWAY FROM
APPLIANCE.
TYPE OF FUEL: WOOD ONLY.
PREVENIR LES FEUX DE CREOSOTE:
INSPECTEZ LA CHEMINEE OU LE RACCORD
DE CHEMINEE, SI APPLICABLE, DEUX FOIS
PAR MOIS ET NETTOYEZ SI NECESSAIRE.
NE SURCHAUFFEZ PAS: SI L'EXTERIEUR DE
L'UNITE DEVIENT ROUGE, VOUS
SURCHAUFFEZ.
GARDEZ LES MEUBLES ET AUTRES
MATERIELS COMBUSTIBLES A UNE
DISTANCE CONSIDERABLE DE L'APPAREIL
DE CHAUFFAGE.
TYPE DE COMBUSTIBLE: BOIS SEULEMENT.
IMPORTANT
BEFORE COMMENCING INSTALLATION
REFER TO THE LABEL LOCATED BEHIND
THE FACEPLATE AND TO THE
MANUFACTURER'S INSTALLATION
INSTRUCTIONS PACKAGED TOGETHER
WITH THIS UNIT.
THE INSTALLATION MUST BE APPROVED
BY THE AUTHORITY HAVING
JURISDICTION.
AVANT DE COMMENCER L'INSTALLATION,
REFEREZ-VOUS À L'ÉTIQUETTE QUI SE
TROUVE DERRIÈRE LA FAÇADE AINSI
QU'AUX INSTRUCTIONS D'INSTALLATION
DU MANUFACTURIER FOURNIES AVEC
L'UNITÉ.
L'INSTALLATION DOIT ÊTRE APPROUVÉE
PAR L'AUTORITÉ COMPÉTENTE.
24 NAPOLEON ROAD. BARRIE, ONTARIO L4M 0G8 CANADA
INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OWNER'S
MANUAL. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION
INSPECTION IN YOUR AREA. DO NOT CONNECT THIS UNIT TO A CHIMNEY SERVING ANOTHER APPLIANCE.
WARNING:
• Operate with feed doors
closed. Open to feed fire only.
• Transport ashes in an air-tight non-combustible
container.
• For use with cord wood only.
• Not for use in a Mobile Home.
• Combustion air openings are not to be obstructed.
MINIMUM CHIMNEY HEIGHT 15 ft (4.57 m) MAXIMUM NUMBER OF ELBOWS 4
MAXIMUM CHIMNEY HEIGHT 34 ft (10.36 m) FLUE COLLAR 8"ø
MAXIMUM OFFSET ANGLE 30º US - 45º CANADA
HAUTEUR MINIMALE DE LA CHEMINÉE 15 pi (4.57 m) NOMBRE MAXIMAL DE COUDES 4
HAUTEUR MAXIMALE DE LA CHEMINÉE 34 pi (10.36 m) BUSE D'ÉVACUATION 8"ø
ANGLE DE DÉVIATION MAXIMAL 30º US - 45º CANADA
9700539 (WSL)
4001657 (NGZ)
4001658 (NAC)
4001659 (WUSA)
AVERTISSEMENT:
• Tenir les portes fermées lorsque le foyer fonctionne.
N’ouvrez que pour ravitailler le feu.
• Transporter les cendrew dans un contenant
incombustible possédant un couvercle étanche.
• Pour emploi avec du boid de corde seulement.
• Ne peut être installé dans une maison mobile.
• Les ouvertures d’air de combustion de doivent pas être
obstruées.
WARNING: THIS APPLIANCE HAS NOT BEEN TESTED WITH
AN UNVENTED GAS LOG SET. TO REDUCE RISK OF FIRE OR
INJURY, DO NOT INSTALL AN UNVENTED GAS LOG SET
INTO APPLIANCE.
AVERTISSEMENT: CET APPAREIL N’A PAS ÉTÉ TESTÉ AVEC
LES BÛCHES À GAZ. POUR RÉDUIRE LES RISQUES
D’INCENDIE OU DE BLESSURES, NE PAS INSTALLER UN
BÛCHES À GAZ DANS L’APPAREIL.
Do not use a fireplace insert or other products not specified for use with this product.
N’utiliser pas un insert de cheminée ou d’autres produits non spécifiées pour l’utilisation avec ce produit.
Replace only with ceramic glass obtained from the dealer and certified for use with this fireplace.
Remplacez uniquement avec du verre obtenu du détaillant et certifié pour l’utilisation avec cet appareil.
MANUFACTURE DATE:
YEAR: 2015 2016 2017 2018
MONTH:
2019 2020
243658710912111
OPTIONAL COMPONENTS / PIECES OPTIONNELS
BLOWER KIT / SOUFFLERIE : NZ64
HOT AIR GRAVITY VENTS / VENTILATION PAR GRAVITE: NZ221
ACCESSORIES PROVIDED BY MANUFACTURER ARE TO BE UTILIZED ONLY/
SEULS LES ACCESSOIRES FOURNIS PAR LE FABRICANT PEUVENT ÊTRE UTILISÉS.
NZ6000-1
SAMP
THE MANUFACTURER'STURER'S
ERATING MANUAL.
E
PLATE
LATE
F UNIT
UNIT
OF UNIT
NIT
SE OF UNIT
T
SA
MP
M
M
M
M
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
M
AM
AM
AM
AM
AM
AM
AM
AM
AM
AM
M
M
M
M
M
M
M
F
ace
a
n
d
e
n
c
l
osu
r
eFace and enclosure
ceiling metal studs, boceiling metal studs,
clad with cement bclad with cemen
Face
m
us
t h
a
v
e
aFace must have a
m
inimum 8' hei
g
h
tinimum 8' height
o
f
ce
m
e
nt
boa
r
d
ement board
ement board and steel studsent board and st
C
ement board
f
rom
Cement board from
th
e
s
i
de
o
f th
e
u
ni
tthe side of the unit
t
o
co
m
bus
ti
b
l
esto combustibles
f
acin
g
and wood
od
f
ramin
g
ma
y
star
t
at 96" above th
e
base
of
th
e
u
nit
Metal Studsuds
M
AM
AM
M
M
AM
M
OLED CHIMNEY MINIMUM CLEARANCES TO COMBUSOLED CHIMNEY MINIMUM CLEARANCES
A
A
Face must h
minimumm
of cemo
A
Cemen
ONJ
S
EMENTS
S
S
S
S
S
N SEE THE MANUFACSEE THE MANUFAC
ERATING MANUARATING MANU
"(0 mm)"(0 mm)
TO STAND-OFFSTO STAND-O
72"(2.83 m)72"(2.83 m)
FROM BASE OF UNITFROM BA
2"(51 mm)2"(51 mm
REFER TO MANUFACTURER'S
NUFACTUR
INSTALLATION INSTRUCTIONS.
ATION INSTRUCTION
12"(305 mm)12"(30
TO TOP EDGE OF FACEPLATE
OP EDGE OF FACEPLATE
84"(3.31 m)84"(3.31
FROM BASE OF UNITFROM BASE OF UNIT
6"(153 mm)6"(153 mm)
FROM SIDE OF UNITFROM SIDE OF UN
ALL
L
21"(534 mm)21"(534 mm)
TO EDGE OF FACEPLATETO EDGE OF FACEPLATE
N
21"(534 mm)21"(534 mm)
FROM FRONT OF UNITFROM
"(203 mm)
)
FROM SIDES OF UNIT
T
3.31 m)
FROM BASE OF UNIT
M BASE OF UNIT
M
M
La façade doit pooit
panneau de
hauteur
Panneau de ciment et montanPannea
d'acier sur le plafond de l'end'acier sur le
non requis à plus denon requis
M
M
M
M
M
La
PannPa
M
M
M
M
O NOT REMOVE THIS LABELHIS LABEL
NE RETIREZ PASNE RETIREZ PAS
MP
MP
MPLE
M
M
M
MP
M
M
M
MP
MP
MP
MP
MP
MP
POSANTS REQUIS POUR L'INSTALLATION:OSANTS REQUIS POUR L'INSTALLATION:
EXIGENCES POUR LA CHEMINÉE (voir le mCES POUR LA CHEMINÉE (voir le
La cheminée doit être certifiée selon l'une des normes suivadoit être certifiée selon l'une des normes suiv
pour le Canada ou selon les normes UL 103HT oule Canada ou selon les normes UL 103HT ou
Installation dans une cheminée en maçonnerie : Laation dans une cheminée en maçonnerie : La
certifiée selon les normes ULC S640 M92 ou ULCcertifiée selon les no
UL 1777 pour les
Cheminée refroidie à l'air : U
(see installation manual):(see installation manual):
H FACEPFACEP
E
PLATE SCREWSATE SCREWS
HIPPED WITH THE DOOR(S):PPED WITH THE
INSTALLATION INSTRUCTIONS ANDNSTALLATION INSTRUCTIONS AN
H
ARDWAR
EHARDWARE
f the following standards ULC S604, ULC S610following standards ULC S604, ULC S
r UL 103HT or UL-127 for the United StatesHT or UL-127 for the United State
Stainless steel liner must be certified to ULC S640el liner must be certified to U
or Canada or UL 1777 for the United States777 for the United State
cooled chimney: Use only FMI 8DMy FMI 8DM
É AVEC LE FOYERLE FOYER
ANUEL D'INSTRUCTIONSRUCTIONS
DÉFLECTEUR
PARE-BRAI
S
E
SARE-BRA
PARE-B
ÛC
HE
SPARE-BÛCHES
G
AINE FLEXIBLE AVE
C
CO
LLET DE RA
CCO
RD
GAINE FLEXIBLE AVEC COLLET DE RACCOR
DE PRISE D'AIR DE 10', 6" DE DIAMÈTRE
DE PRISE D'AIR DE 10', 6" DE DIAMÈTRE
(
P
O
UR LA
SO
UFFLERIE ET
(POUR LA SOUFFLERI
L'APPROVISIONNEMENT EN AIR EXTÉRIEUR
)L'APPROVISIONNEMENT EN AIR EXTÉRIEUR)
LIVRÉ AVEC LA FAÇADE
:FAÇADE :
F
A
Ç
AD
E
12 VIS P
O
UR LA FAÇAD
EUR LA FAÇAD
LIVRÉ AVEC LA/LES PRÉ AVEC LA/LES
INSTRUCTIONS D'INSTRUCTIONS D
ET QUINCAILLERET QUINCAILLE
MP
LE
P
E
A
TYP
PREVE
INSPECTEECTE
DE CHEMINEE CHEMINE
PAR MOIS ET N
PAR MOIS ET N
NE SURCHAUF
NE SURCHAU
L'UNITE DEVL'UNITE DE
SURCHAUSURCHA
GARDEGARD
MATMA
D
MP
OLEON ROAD. BARRIE, ONTARIO L4M 0G8 CANADAD. BARRIE, ONTARIO L4M 0G8 C
EIGHT 15 ft (4.57 m) MAXIMUM NUMBER OF ELBOWS 4M NUMBER OF ELBOWS 4
Y HEIGHT 34 ft (10.36 m) FLUE COLLARAR
8
"
ø8"ø
T ANGLE 30º US - 45º CANADA
HAUTEUR MINIMALE DE LA CHEMINÉE 1HAUTEUR
HAUTEUR MAXIMALE DE LA CHEMINÉHAUTEUR MA
ANGLE DE DÉVIATION MAXIMALANGLE DE DÉV
fonctionne.nctionne.
feu.eu.
un contenantcontenant
uvercle étanche.ercle étanche.
e corde seulement.corde seulement.
s une maison mobile.une maison mobile.
mbustion de doivent pas êtretion de doivent pas être
struées.
MP
P
uit.t.
ce.e.
appareil.ppareil.
MP
ÉS.S.

W415-1501 / E / 12.17.18
EN
9
3.0 installation overview
SEE
CHIMNEY
INSTALLATION
SEE
MINIMUM
MANTEL
CLEARANCES
SEE
FIREBRICK
INSTALLATION
SEE
GLASS AND
GASKET
REPLACEMENT
&
CARE OF GLASS
SEE
HEARTH
EXTENSION
SEE OPTIONAL
NZ64
BLOWER
INSTALLATION
SEE
HIGH
EFFICIENCY
HEATING
SEE
DOOR HANDLE
INSTALLATION
SEE
CONNECTION
TO A MASONRY
CHIMNEY
SEE
OUTSIDE
COMBUSTION
AIR
SEE
OUTSIDE
COMBUSTION
AIR
SEE
FRAMING
SEE
RATING PLATE
INFORMTATION
SEE
VENTILATION
OPENINGS
!WARNING
• This appliance and its components are designed to be installed and operated as a system. Any alteration
to or substitution for items in this system, unless allowed by these installation instructions, will void the ETL
listing and may void the product warranty. It may also create a hazardous installation. Read through these
instructions thoroughly before starting your installation and follow them carefully throughout your project.

W415-1501 / E / 12.17.18
EN
10
4.0 installation planning
!WARNING
• Wear gloves, protective footwear and safety glasses for protection.
• Carefully follow the instructions for assembly of the pipe and other parts needed to install the appliance.
Failure to do so may result in a fire, especially if combustibles are too close to the appliance or chimney and air
spacers are blocked, preventing the free movement of cooling air.
• Do not draw outside air from garage spaces. Exhaust products of gasoline engines are hazardous. Do not
install outside air ducts such that the air may be drawn from attic spaces, basements or above the roofing
where other heating appliances or fans and chimneys exhaust or utilize air. These precautions will reduce the
possibility of appliance smoking or air flow reversal. The outside air inlet must remain clear of leaves, debris, ice
and/or snow. It must be unrestricted while appliance is in use to prevent room air starvation which can cause
smoke spillage and an inability to maintain a fire. Smoke spillage can also set off smoke alarms.
• Negative pressure within your home may inadvertently affect your appliance.
• To prevent contact with sagging or loose insulation, the appliance must not be installed against vapour barriers
or exposed insulation. Localized overheating could occur and a fire could result.
• Do not use makeshift compromises during installation. Do not block or restrict air, grille or louvre openings. Do
not add a hood.
• To prevent personal injury, keep hand tools in good condition, sharpen cutting edges and make sure tool
handles are secure.
• Always maintain the minimum air space required in the enclosure to prevent fires.
• Check with local building officials for any permits required for installation of this appliance and notify your
insurance company prior to proceeding.
!WARNING
• Do not install into any area having a height less than 7 feet (2.1m) (ceiling of enclosure to appliance
bottom, excluding hearth height).
The appliance is shipped with a set-up face that is 1/8" (3.2mm) larger on the top,
bottom and each side than the faceplate. Leave the set-up face in place to act as a
template when installing the finishing face.
important:
This appliance, fully dressed, weighs 850lbs (386kg). Ensure there is
adequate floor support for the appliance, chimney, and facing material.
Some material could weigh thousands of pounds.
We recommend that the appliance be secured to the floor in
all cases.
Using the door opening as a datum, level the appliance by
shimming underneath the appliance. Remove and discard the
lifting handles. Bend the tabs down and secure the appliance to
the floor.
4.1 location and clearances

W415-1501 / E / 12.17.18
EN
11
installation planning
Install ventilation grilles (minimum openings of 40 sq. inches (0.03 sq. meters)) at both floor and ceiling levels of the
enclosure. These grilles must not restrict the flow of heat by more than 25%. Do not install into any area having
a height less than 7 ft (2m) (ceiling of enclosure to appliance bottom, excluding hearth height). The location of
windows, doors and the traffic flow in the room where the stove is to be located should be considered. If possible,
you should choose a location where the chimney will pass through the house without cutting a floor or roof joist.
For more information on ventillation grilles and openings, see "when using a solid pack chimney" section.
note:
In order to avoid fire hazards and/or injuries, the appliance enclosure must be provided with sufficient air
circulation.
10' (3m) MIN. TO
CHIMNEY CAP.
Insulating the intake liners is recommended in colder
climates to prevent condensation from occurring.
The Napoleon Model NZ6000-1 takes outside air
directly into the appliance through the openings in the
left and right hand sides.
Decide on the most convenient location for the fresh air
inlet ducts and hoods which may be installed above or
below floor level.
The fresh air inlet ducts and hoods must be installed.
Secure and seal the intake liners to the collars using 3
sheet metal screws, and high temperature sealant.
note:
Incorporate a vertical loop or trap into air liners to reduce air flow when appliance is not in use.
Horizontal run may be:
5' (1.5m)
15' (4.6m)
20' (6.1m)
25' (7.6m)
Vertical rise is between:
6' (1.8m) & 10' (3m) max
3' (0.9m) & 6' (1.8m)
1' (0.3m) & 3' (0.9m)
0' (0m) & 1' (0.3m)
0
2 (4)
4 (8)
6 (12)
8 (16)
10 (20)
5
(10)
10
(20)
15
(30)
20
(40)
25
(50)
AIR INTAKE LINERS
HORIZONTAL RUN
VERTICAL RISE
Included with the appliance are:
- Two 10' (3m) lengths of vent. Use a connector
and seal if adding more length.
- Two of intake hoods.
The vertical height of the air intake liner must not be greater than
2/3 the height of the chimney. If additional liner length is required, it may
be doubled by increasing the size from 6" (152mm) diameter to 8" (203mm)
diameter. Use a 6" (152mm) to 8" (203mm) increaser at the hood and a
decreaser at the appliance. Values in brackets represent 8" (203mm) diameter
intake liners.
The duct terminations must be located so they can not be blocked (i.e.
snowdrifts). 4' (1.2m) above grade is recommended. Make a 6 ½" (165mm)
inch hole to suit in an outside wall of the house. From outside, place the fresh
air hood into the hole, open side down. Seal with caulking and secure.
4.2 ventilation openings
4.3 outside combustion air

W415-1501 / E / 12.17.18
EN
12
installation planning
4.4 floor protection
4.4.1 ember strip and hearth extensions
An acceptable 61 ½" (156.2cm) x 20" (50.8cm) non-combustible (ie:
brick, stone or ceramic tile) hearth extension must be installed. Hearth
must extend 20" (50.8cm) in front of the faceplate when it is not elevated
(see local building codes). Hearth must extend a minimum of 6" (152mm) to
both sides of the appliance [61 ½" (156.2cm)].
The hearth must extend a minimum 20" (50.8cm) in front of the appliance
although if raised a minimum of 6 1/2" (165mm), the 20" (50.8cm) may be
reduced to a minimum of 18" (45.7cm).
The hearth must extend a minimum of 6" (152mm) to both sides of the
appliance [61 ½" (156.2cm)]
The hearth must be a minimum of 1" (25mm) thick cement board (or
equivalent) plus ¼" (6.4mm) ceramic tile.
Ensure that the gap between the appliance and a non-combustible
hearth extension is sealed with sand/cement grout or covered with
an ember strip (or both) to prevent sparks and embers from falling
into this area.
Raised hearths must be constructed of non-combustible materials such as cement blocks or bricks.
While the appliance can be installed directly on the floor, a non-combustible hearth extension is required in front
of the appliance, that must not be built higher than the bottom of the appliance faceplate. It may therefore be
advisable to build the appliance on a raised platform.
A raised hearth together with the appliance built on a raised platform is recommended for easier wood loading and fire
viewing.
EMBER STRIP
(See “HEARTH
EXAMPLES” Section)
!WARNING
• Hearth extensions are to be installed only as described to prevent high temperatures from occurring on
concealed combustible materials. Hearth ember strips prevent burning or hot particles from inadvertently falling
directly on combustible surfaces in the event the building should settle and disturb the original construction.

W415-1501 / E / 12.17.18
EN
13
installation planning
4.4.2 hearth extension
18" (457mm)
6 1/2"
(165mm)
61 1/2"
(1562mm)
61 1/2" (1562mm)
20" (508mm)
6"
(152mm)
6"
(152mm)
An acceptable 61 ½" (156.2cm) x 20" (50.8cm) non-combustible (ie: brick,
stone or ceramic tile) hearth extension must be installed. Hearth must
extend 20" (50.8cm) in front of the faceplate when it is not elevated (see
local building codes). Hearth must extend a minimum of 6" (152mm) to
both sides of the appliance [61½" (156.2cm)].
Hearth must be a minimum of 1" (25mm) thick cement board (or
equivalent) plus ¼" (6.4mm) ceramic tile.
Ensure that the gap between the appliance and a combustible hearth
extension is sealed with sand/cement grout or covered with a metal strip
(or both) to prevent sparks and embers from falling into this area.
HEARTH EXTENSION
Elevated hearths must be constructed of noncombustible materials such
as cement blocks or bricks.
While the appliance can be installed directly on the floor, a non-
combustible hearth extension is required in front of the appliance, that
must not be built higher than the bottom of the appliance faceplate. It may therefore be advisable to build the
appliance on a raised platform.
Hearths raised minimum 6 ½" (165mm) must extend a minimum of 18" (45.7cm).
EMBER STRIP
SEE HEARTH
EXAMPLES

W415-1501 / E / 12.17.18
EN
14
installation planning
4.4.3 hearth examples
NON-COMBUSTIBLE MATERIALS
SUCH AS CEMENT
BLOCKS OR BRICKS
COMBUSTIBLE FRAMING
PLYWOOD INCREASE
HEADER HEIGHT
THIS DIMENSION
See “Framing” section
RAISED
APPLIANCE
COMBUSTIBLE FRAMING
NON-COMBUSTIBLE
MATERIALS SUCH
AS CEMENT BLOCKS
OR BRICKS
PLYWOOD
INCREASE
HEADER HEIGHT
THIS DIMENSION
See “Framing” section
RAISED
HEARTH
RAISED
APPLIANCE
COMBUSTIBLE FLOOR
EMBER STRIP
EMBER STRIP
EMBER STRIP
EMBER STRIP
COMBUSTIBLE FLOOR
MIN. 1/4” (6.4mm)
TILE OR MARBLE 20” MIN.
(50.8cm)
MIN. 1” (25mm) CEMENT BOARD
6
1/2
”
(165mm)
20” MIN.
(50.8cm)
MIN. 1/4” (6.4mm)
TILE OR MARBLE
MIN. 1” (25mm)
CEMENT BOARD
MIN. 1/4” (6.4mm)
MARBLE OR STONE
20” MIN.
(50.8cm)
20” MIN.
(50.8cm)
FACEPLATE
FACEPLATE
FACEPLATE
FACEPLATE
WARNING:
Ensure raised
platform is
designed to
support load of
fully loaded
appliance.
WARNING:
Ensure raised
platform is
designed to
support load of
fully loaded
appliance.
FLUSH HEARTH
RAISED HEARTH
RAISED APPLIANCE
RAISED HEARTH AND APPLIANCE
18" MIN.
(45.7cm)
18" MIN.
(45.7cm)

W415-1501 / E / 12.17.18
EN
15
5.0 installation
!WARNING
• Never install a single wall slip section or smoke pipe in a chase structure. The higher temperature of this single
wall pipe may radiate sufficient heat to combustible chase materials to cause a fire.
• To avoid danger of fire, all instructions must be strictly followed, incluidng the provision of air space clearance
between chimney system and enclosure. To protect against the effects of erosion on those parts exposed to
the weather, we recommend that the chase top be painted with a rust-resistant paint.
• Maintain a minimum 2" (51mm) air clearance to all parts of the chimney system at all times. Failure to maintain
this 2" (51mm) air clearance will cause a structure fire.
• Detailed instructions for installation of the chase top, storm collar, and termination cap are packaged with these
parts.
• Firestop spacers must be used whenever the chimney penetrates a ceiling/floor area.
• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year, and as
required.
A raised hearth, together with the appliance built on a raised platform, is recommended for easier wood loading
and fire viewing.
5.1 chimney
ANCHOR PLATE
ANCHOR PLATE GASKET
APPLIANCE TOP
ANCHOR PLATE FOR A FACTORY
BUILT CHIMNEY
This appliance was tested to CAN/ULC S610 and UL 127 Factory Built Fireplace Standards. This appliance has
met the test criteria for Zero Clearance Installation to Combustible Surfaces and Certified to burn firewood only.
Any chimney listed to the following standards; CAN/ULC-S604 and CAN/ULC-S629 for Canada or UL-103 or UL-
103HT for the United States may be installed.
Installation of all types of factory-built chimney systems is to be in
accordance with the chimney manufacturers installation instructions.
An appropriate chimney manufacturers anchor base plate and anchor
base plate gasket is required in order to initiate their system. Use
the high temperature gasket, supplied, to seal between the anchor
plate and the appliance top. Air cooled chimney systems are not
recommended in colder climates.
For complete installation instructions, refer to instructions provided with
the manufactured chimney system.
A chimney venting the appliance shall not vent any other appliance. The minimum overall chimney height from
the top of the appliance is 15ft (4.6m). The maximum overall chimney height from the top of the appliance is 34ft
(10.4m).
Factory-built chimney systems for use in dwellings constructed for three or more families must be enclosed
above the room in which the appliance is located. This enclosure must have a fire resistance rating equal to or
greater than that of the floor or roof assembly through which they pass.
The chimney should not be built with an offset angle in excess of 45° in Canada and 30° in USA.
Ensure that minimum clearances are maintained.
Portions of the chimney that extend through accessible spaces must always be encased to avoid personal
contact with the chimney and thereby avoid damage to the chimney.
The chimney must be supported at a maximum of 20ft (6.1m) intervals. Every 20 ft (6.1m) of chimney can weigh
up to approximately 200lbs (90.7kg).
note:
All venting connections must be in compliance with the chimney manufacturer’s installation instructions.
note:
Use only the chimney diameter specified on the rating plate of the
appliance.

W415-1501 / E / 12.17.18
EN
16
installation
5.2 typical chimney installation
* The first flue offset closest to the top of the appliance must be a
minimum distance of 12” (30.5cm) from the top of the appliance.
A. Move the appliance into position. Try to center the exhaust
flue of the appliance, midpoint between two joists to prevent
having to cut them. Use a plumb bob to line up the centre.
B. Cut and frame an opening in the ceiling to provide a
minimum clearance of 2” (50.8mm) between the outside of
the chimney and any combustible material. DO NOT FILL
THIS SPACE WITH ANY TYPE OF MATERIAL! Nail headers
between the joists for extra support. Firestop spacers must
be placed on each framed opening in any floor or ceiling
that the chimney passes through.
C. Hold a plumb bob from the underside of the roof to
determine where the opening in the roof should be.
Cut and frame the roof opening maintaining proper
2” (50.8mm) clearances.
HEADERS
FIRESTOP SPACER -
UNDERSIDE OF JOIST
15 FT
(4.6m)
MINIMUM
34 FT
(10.4m)
MAXIMUM
RAIN CAP RAIN CAP
RAIN CAP
STORM COLLAR
ROOF FLASHING
STORM COLLAR
ROOF FLASHING
STORM COLLAR
ROOF FLASHING
ATTIC INSULATION
SHIELD
ATTIC INSULATION
SHIELD ATTIC INSULATION
SHIELD
CEILING RADIATION
SHIELD
OFFSET
SUPPORT
OFFSET
SUPPORT
FIRESTOP FIRESTOP
12” (30.5cm)
MIN*
15 FT
(4.6m)
MINIMUM
34 FT
(10.4m)
MAXIMUM
12” (30.5cm)
MIN*
15 FT
(4.6m)
MINIMUM
34 FT
(10.4m)
MAXIMUM
STRAIGHT CHIMNEY SINGLE OFF-SET CHIMNEY DOUBLE OFF-SET CHIMNEY
2" (50.8mm)
Min.
Typical Roof Joist FramingTypical Joist Framing
2" (50.8mm)
Min.
2" (50.8mm)
Min.
2" (50.8mm)
Min.
note:
30° or 45° offsets may be installed back to back.

W415-1501 / E / 12.17.18
EN
17
installation
5.3 adding chimney sections
Add chimney sections, according to the manufacturer’s installation instructions. If the chimney system passes
through an attic space, a rafter radiation shield or attic insulation shield is required. The chimney must extend at
least 3ft (0.9m) above its point of contact with the roof and at least 2ft (0.6m) higher than any wall, roof or building
within 10ft (3.1m). If the chimney extends more than 5ft (1.5m) above the roof, it must be secured using a roof
brace or guide wires. A raincap must be installed to avoid internal damage and corrosion.
3 FT (1m)
MIN
3 FT (1m)
MIN
10 FT (3m)
OR MORE
FLAT ROOF WALL
RIDGE
LESS THAN
10FT (3m)
2 FT (0.6m) MIN 3 FT (1m)
MIN
2 FT (0.6m)
MIN
LESS THAN
10FT (3m)
3 FT (1m)
MIN 2 FT (0.6m)
MIN
10 FT (3m)
TO NEAREST
ROOFLINE
Floor, Ceiling Joist
LIVING SPACE
Framed
Enclosure
2” (51mm)
clearance from
chimney to
combustible wall
Chimney Lengths
Ceiling Joist
Chimney must be
totally enclosed
when passing
through living space
with a minimum 2”
(51mm) clearance
to combustibles.
ATTIC SPACE
note:
This illustration is for wood appliances only.

W415-1501 / E / 12.17.18
EN
18
installation
5.4 offset chimney installation
The first flue offset closest to the top of the
appliance must be a minimum distance of
12" (30.5cm) from the top of the appliance.
Attach an elbow to the chimney section, angled
toward the offset. Secure according to chimney
manufacturer’s instructions. Chimney sections must
be adequately secured one to the other to ensure
they do not separate. To achieve the minimum
offset, attach and secure a second elbow. To
achieve longer offsets, you may install any available
length of chimney pipe between the elbows.
Supports must be used on the first vertical chimney
section after a return elbow.
Attic Insulation
Shield
Storm Collar
Elbow
Elbow Support
Straps
Elbow
Roof
Flashing
Rain Cap
Elbow Support
Band
Roof Joist
Chimney Section
Floor , Ceiling Joist
Firestop
If the offset length is more than 36” (91.4cm), an
intermediate support must be employed. To
achieve longer offsets, you may install any
available length of chimney pipe between the
elbows.The intermediate support must be used
in conjunction with an offset support.
!WARNING
• Chimney sections installed between an offset and return require structural support to reduce off-center
loading and to prevent chimney sections from separating at the chimney joists.
• The chimney should not be built with an offset angle in excess of 45° in Canada and 30° in USA. Do not
combine offset chimney components to exceed these angles.

W415-1501 / E / 12.17.18
EN
19
installation
5.5 installing flashing and storm collar
RAIN CAP
CAULKING
STORM COLLAR
WEATHER
SEALANT
FLASHING
The following are generic installation instructions for installing the flashing around a chimney. Installation of all
types of factory-built chimney systems is to be in accordance with the chimney manufacturer’s installation
instructions. Remove the nails from the shingles above and to the sides of the chimney. Place the flashing over
the chimney pipe and slide underneath the sides and upper edge
of the shingles. Ensure that the chimney pipe is properly
centered within the flashing, giving a 3/4” (19.1mm) margin all
around. Fasten to the roof on the top and sides. DO NOT NAIL
through the lower portion of the flashing. Make weather-tight by
sealing with caulking. Where possible, cover the sides and top
edges of the flashing with roofing material. Apply waterproof
caulking, provided with the flashing, around the chimney, 1”
(25.4mm) above the top of the flashing and push the storm collar
down into the caulking. Insert a rain cap onto the top of the last
chimney section.
5.6 connection to a masonry chimney
The appliance may be connect-
ed to either a lined or unlined
masonry chimney.
IF THE CHIMNEY IS LINED:
The flues must be made of
vitrified clay and be in sizes
of 8” (203.2mm) square or
8” (203.2mm) round (inside
diameters) or 8”x12” [(203.2mm
x 304.8mm)] with a minimum
height of 15 feet (4.6m) above
the appliance.
8” (203.2mm) round flues are
recommended.
Installation must conform to both national and local code requirements.
IF THE CHIMNEY IS UNLINED:
A stainless steel liner listed to either Standard ULC-S640M in
Canada or UL-1777 in the USA, must be used. Liners for new
masonry chimneys may be used to connect the appliance to the
chimney. The liner must be continuous from the appliance to the
chimney cap and be installed only per manufacturers instructions.
In both cases, the chimney structure must be supported by angle
iron anchored into the masonry walls. The allowable masonry used
in chimney construction is 3 1/2” (88.9mm) brick, solidly mortared
and must fully encase the flue. Ensure there are no leaks.
In no case is the masonry enclosure to be supported by the appliance. Allow a 1” (25.4mm) air cavity for expan-
sion. Use the flue tile support accessory, see your local authorized dealer / distributor.
ANGLE IRON RESTS
ON BRICK SIDE-WALLS,
FREE OF UNIT.
FLUE TILE
HI-TEMP GASKET
ANGLE IRON TO SUPPORT
CHIMNEY WEIGHT
FLUE TILE
SUPPORT
APPLIANCE TOP
UNLINED CHIMNEY INSTALL
USE AN 7” (177.8mm)
OR 8" (203.2mm) LINER
WITH A DRIPLESS TYPE
A CONNECTOR
(IF USING 7” (177.8mm)
A 7” TO 8” INCREASER
FROM LINER TO FLUE
ALSO CAN BE USED.)
LINER
SUPPORT
LINED CHIMNEY INSTALL
HI-TEMP GASKET
APPLIANCE TOP
FOR A MASONRY APPLIANCE USE A
FLUE TILE SUPPORT. FOR A
PRE-FABRICATED CHIMNEY USE AN
ANCHOR PLATE.
note:
The flue tile support is to be suspended on appropriate lintels.

W415-1501 / E / 12.17.18
EN
20
installation
5.7 air cooled chimney installation
A. Remove the knock out.
B. Cut away the insulation to gain access to the ring.
C. Remove the ring secured by four screws.
D. Slide the starter collar through the insulation wrap and
affix using the four screws removed in step C.
E. Secure the inner liner of the chimney to the appliance 8"
(203mm) collar using 3 screws supplied with the starter
collar (W170-0098).
F. Follow the chimney manufacturer's instructions for
installing the chimney.
Use only the following brand and type of chimney.
CHIMNEY COMPONENTS FMI 8DM
12" (304.8mm) Chimney Section 12-8DM
18" (457.2mm) Chimney Section 18-8DM
24" (609.6mm) Chimney Section 24-8DM
36" (914.4mm) Chimney Section 36-8DM
48" (1219.2mm) Chimney Section 48-8DM
Offsets 30E-8DM
Flashing 6F8 or 12F8
Chimney Cap RTL-8HT
Roof Support 38 RS
Firestop FS-8DM
CHIMNEY COMPONENTS WOLF STEEL
Starter Collar NZAC-KT
KNOCK-OUT
1
INSULATION
2
STARTER COLLAR
4
RING
3