Nasco Life/form Airway Larry User manual

Copyright © 1999 HC190001INM8
ONLINE: NascoHealthcare.com
EMAIL: [email protected]
PHONE: [phone]
ADDRESS: 901 Janesville Ave.
Fort Atkinson, WI 53538
HEALTHCARE
HEALTHCARE
“Airway Larry”
Airway Management
Trainer Head
LF03667U
INSTRUCTION MANUAL
WARNING: Products may contain dry natural rubber.
5-Year Warranty
Other Available Simulators
LF03000U CPARLENE
®
Series
LF03601U Adult Airway Management
Trainer with Stand
LF03602U Adult Airway Management
Manikin
LF03609U Child Airway Management
Trainer with Stand
LF03616U Child CRiSis™ Manikin
LF03617U Deluxe Child CRiSis™
Manikin with Arrhythmia Tutor
LF03620U PALS Update Kit
LF03623U Infant Airway Management
Trainer with Stand
LF03632U Child Intraosseous Infusion/
Femoral Access Leg on a Stand
LF03633U Child Airway Management
Trainer Torso
LF03693U Basic Buddy
®
CPR Manikin
LF03699U “Airway Larry” Airway
Management Trainer
LF03709U Infant CRiSis™ Manikin
LF03720U Baby Buddy
®
Infant
CPR Manikin
LF03750U Bariatric CPR Manikin
LF03760U Airway Management/Cricoid
Pressure Trainer
LF03770U Chest Tube
LF03953U CRiSis™ Manikin, Complete
LF03955U Deluxe CRiSis™ Manikin
LF03956U Deluxe “Plus” CRiSis™ Manikin
LF03965U Adult CRiSis™ Auscultation
Manikin
LF03966U Adult CRiSis™ Auscultation
Manikin with ECG Simulator
LF04200U Adult Sternal Intraosseous
Infusion
LF06001U CPR Prompt® Adult/Child
Manikin
LF06012U CPR Prompt® Infant Manikin
LF06200U CPR Prompt® Keychain
Rescue Aid
LF06204U CPR Prompt® Rescue and
Practice Aid
Practice Aid
LF03840U
SUPPLIES AND REPLACEMENT PARTS
LF03605U Replacement Lungs
LF03606U Replacement Stomach
LF03644U Pump Spray Lubricant
LF09919U Nasco Cleaner
LF03214U
HC190001INM8.indd 1-2 1/15/19 2:03 PM

2 7
ABOUT THE SIMULATOR
The Life/form®“Airway Larry” Airway Management Trainer Head is a realistic simulator available
for the training of intubation and other airway management skills. The airway management trainer is
anatomically correct in respect to both size and detail. Landmarks include nostrils, teeth, tongue, oral
and nasal pharynx, larynx, cricoid ring, epiglottis, arytenoid, false and true vocal cords, trachea, and
esophagus.
Nasco’s “Airway Larry” allows you to practice oral, digital, and nasal intubation. E.T., E.O.A., P.T.L.®,
L.M.A., E.G.T.A., Combitube®, and King System insertion can all be practiced as well (please see section
titled “Using the Combitube®”). Suction techniques and proper cuff inflation can also be performed and
evaluated.
In addition, this model also allows students to apply cricoid pressure during the intubation procedure
(Sellick’s Maneuver). By locating the larynx and depressing the cricoid ring, the student may realistically
lower the vocal cords farther into the field of view. This also effectively closes off the esophagus of the
simulator.
Install your new “Airway Larry” Airway Management Trainer Head to update any CPARLENE® mani-
kins and torsos, use as a stand alone trainer, or as a replacement head for any Adult CRiSis™manikin,
torso, or Airway Management Trainer with stand. With proper care, your Life/form®Airway
Management Trainer will provide years of valuable service. Please review the instructions carefully for
setup, cleanup , and maintenance procedures.
LIST OF COMPONENTS
A. “Airway Larry” Airway Management Trainer Head
B. 8-oz. Bottle of Lubricant
C. 3 Red Caps
A.
B.
C.
Actual product may vary slightly from photo. Nasco reserves the right to change product color, materials,
supplies, or function as needed.
Figure 15
Figure 14
B. Cleaning the Airway Management Trainer Head
1. Remove the head from the torso or stand using the same methods previously described. Also
remove the lungs and stomach.
2. Take the trainer to an area with a sink and open counter space. Using the red caps supplied, plug
the right and left bronchi and the esophagus.
3. Stabilize the head on the counter face-up (towels work well for this) with plugged tubes hanging
over the sink. (See Figure 14.)
4. Carefully pour warm soapy water (a mild dish soap works best) into the mouth until the water level
reaches halfway up the tongue.
5. Tilt the head back and bring the neck up 3" off the countertop.
6. Continue filling until the water level covers the tongue. Take a small soft brush and gently scrub the
inside of the mouth (a small toothbrush works well for this). Cotton swabs can be used to scrub
inside the nostrils.
7. When done, pull the red cap from the esophagus and drain the water into the sink.
8. Now pick the head up, hold it in a vertical position, and pull the caps from the bronchi to completely
empty the system. (See Figure 15.)
9. Rinse the airway, following the same procedure used to clean, with warm tap water only. Repeat
this process until all the soap has been flushed from the system.
C. Disinfecting the Airway
To disinfect, repeat the standard cleaning procedure with a bleach solution, as specified by the Centers
for Disease Control.
1. Fill the system with the solution until it reaches the corners of the mouth. Remember to start filling
with the head flat and finish with he neck slightly elevated to ensure that the solution completely fills
all airway passages.
2. Once completely filled with the bleach solution, allow the head to sit for at least 10 minutes.
3. Drain as previously described and repeat the rinsing process to flush out all of the bleach solution.
Set the head aside and allow it to air dry completely prior to next use or storage.
CAUTIONS
• Do not place simulator in contact with any printed paper or plastic. The ink will transfer and cause
an indelible stain. Similar inks, such as ballpoint pen, will also cause an indelible stain.
• Do not use Nasco Cleaner (LF09919U) around the nose or mouth of the simulator. The cleaner
may be toxic if ingested.
• Properly lubricate the Airway Management head and intubation appliances.
• Use only Nasco Pump Spray Lubricant (LF03644U) with this simulator. Other lubricants, such as
silicone oil, may cause damage to the airway of the simulator.
• Ensure intubation appliances are used accordingly. Improper use of intubation appliances could
damage the airway of the simulator. Damage to the airway will require the product to be returned
to Nasco for repair.
HC190001INM8.indd 3-4 1/15/19 2:04 PM

6 3
SETUP
The “Airway Larry” Airway Management Trainer Head is ready to use as a stand-alone trainer upon
delivery. Simply remove it from the carton and unwrap the packaging material. Please note that lung and
stomach bags are not included, but can be purchased separately. See Supplies and Replacement Parts
for part numbers.
LUBRICATION
Before using the Airway Management Trainer, lubricate both the simulator and supplies being used with
the Nasco lubricant provided. (See Figures 1 & 2.)
GENERAL INSTRUCTIONS FOR USE
A. Intubating the Airway Management Trainer
Nasco recommends the use of a 7.5-8 mm endotracheal tube for oral intubation and 7.5 cm or
smaller for nasal intubation. This simulator allows for the Sellick’s Maneuver of applying cricoid pres-
sure during intubation procedures. Ensuring the cuff is properly deflated prior to removal will prolong the
useful life of your simulator. Damage caused by improper use of the simulator will not be covered under
the warranty.
1. Determine the method of intubation.
2. Select the appropriate sized intubation appliance.
3. Generously lubricate the airway and appliance.
4. Intubate the manikin.
5. Visualize chest rise or stomach inflation.
6. Ensure the cuff is properly deflated before removing the appliance.
Note: Remove all appliances prior to storage.
B. Using the Combitube (not included)
Thoroughly read and follow the instructions that come with the combitube. The trainer will accept either
a full size or a small adult tube. As with a real patient, it may be necessary to back the tube out if ventila-
tion cannot be established.
Note: Depending on tube placement, the large cuff may not accept the recommended amount of air. In
this case, simply inflate the cuff to its maximum volume (when the plunger stops) and while holding the
plunger down, detach the syringe from the blue print balloon and proceed.
Figure 2Figure 1
E. Attaching to an Airway Management Trainer Stand
1. Remove the existing head by first removing the lung bags. Set them aside for future use
2. Loosen the pinch clamp on the esophagus and remove the stomach. (See Figure 11.)
3. Turn the existing head until the keyways on the neck and the stand’s head ring attachment align
and you are able to remove the head completely.
4. Lift the head ring attachment on the stand and slide the airway tubes of the new head through the
hole aligning the keyways on the neck to the ring attachment. (See Figure 12.)
5. Slide the head into place and twist to misalign the keyway and return the face to its upward
position.
6. Replace the lung bags and stomach bag, tightening the pinch clamp around the esophagus to
secure the stomach bag. (See Figure 13.)
Figure 11
Figure 12 Figure 13
Figure 10
12. Insert the corrugated bronchus tubes up through the hole in the upper compression plate and
connect the bifurcated lung bags. (See Figure 10.)
13. Replace the chest plate and chest skin, taking care not to pull the skin too tightly across the torso
as this may inhibit chest rise during proper ventilation.
CARE AND MAINTENANCE
A. General Cleaning
Normal surface soil can be removed from the trainer with mild soapy water. Do not allow water to con-
tact electrical components. Stubborn stains may be removed with Nasco Cleaner (LF09919U). Simply
apply the Nasco Cleaner to the soiled area and wipe clean with a soft cloth.
Note: Avoid using cleaner around the mouth area if students will be applying direct mouth-to-mouth
resuscitation techniques, as the cleaner may be toxic if ingested.
HC190001INM8.indd 5-6 1/15/19 2:04 PM

4 5
C. Attaching the “Airway Larry” Airway Management Trainer Head to a Torso
Nasco’s Airway Management Trainer has the ability to be attached to CPARLENE
®
, Adult CRiSis™
Torsos and Manikins, and Life/form®Airway Management Trainer Stands.
Replacing head of CPARLENE
®
with “Airway Larry” Airway Management Trainer Head
1. Remove the chest skin, chest plate, upper compression plate, and compression springs.
(See Figure 3.)
Note: Caution should be used when removing the upper compression plate to avoid damage to the
electronics connected in some models.
2. Disconnect the corrugated upper airway from the clear tube extending from the head of the
manikin.
3. Remove the existing head by turning it face down, aligning the keyways, and pulling it free from
the torso.
4. Install the “Airway Larry” Airway Management Trainer Head using the same method as removing
the head. When inserted at the shoulders, tip the head upward slightly until the two keyways on the
back of the neck slide under the ring and into the top of the torso. (See Figure 4.)
5. Install the CPARLENE
®
Airway to the “Airway Larry” Airway Management Trainer Head by first
connecting the remaining upper airway (corrugated tubing system) to the left bronchus.
6. Use 2 of the supplied red caps to plug the right bronchus and esophagus. (See Figure 5.)
7. Replace the longer exhaust tubing portion of the lower airway through the hole on the inside of the
torso. (See Figure 6.)
8. Replace the compression springs and upper compression plate.
Figure 3 Figure 4
Figure 5 Figure 6
9. Insert the short section of the upper airway through the hole in the upper compression plate and
reattach the lung bag. (See Figure 7.)
10. The lung bag will lay flat on top of the upper compression plate. (See figure 8.)
11. Replace the chest plate and chest skin taking care not to pull the skin too tightly across the torso,
as this may inhibit chest rise during proper ventilation.
Figure 7 Figure 8
D. Replacing Head of CRiSis™Manikins with “Airway Larry” Airway Management
Trainer Head
1. Remove the chest skin and chest plate. Note: Caution should be taken not to damage defibrillation
electronics connected to the chest skin.
2. Disconnect the lung bags from the corrugated bronchus tubes and set aside for future use.
3. Push the bronchus tubes down through the hole in the upper compression plate.
4. Remove the upper compression plate and compression springs.
5. Remove the corrugated bronchus tubes from the airway extending from the existing head and set
aside for future use.
Figure 9
6. Loosen the pinch clamp on the esophagus and pull the stomach tube free from the esophagus
extending from the existing head and set aside for future use.
7. Remove the existing head by turning it face down, aligning the keyways, and pulling it free from the
torso.
8. Install the “Airway Larry” Airway Management Trainer Head using the same method as removing
the head. When inserted at the shoulders, tip the head upward slightly until the two keyways on the
back of the neck slide under the ring and into the top of the torso. (See Figure 4.)
9. Replace the corrugated bronchus tubes. (See Figure 9.)
10. Replace the stomach tube into the esophagus and tighten the pinch clamp. (See Figure 9 inset.)
11. Replace the compression springs and upper compression plate.
HC190001INM8.indd 7-8 1/15/19 2:05 PM

4 5
C. Attaching the “Airway Larry” Airway Management Trainer Head to a Torso
Nasco’s Airway Management Trainer has the ability to be attached to CPARLENE
®
, Adult CRiSis™
Torsos and Manikins, and Life/form®Airway Management Trainer Stands.
Replacing head of CPARLENE
®
with “Airway Larry” Airway Management Trainer Head
1. Remove the chest skin, chest plate, upper compression plate, and compression springs.
(See Figure 3.)
Note: Caution should be used when removing the upper compression plate to avoid damage to the
electronics connected in some models.
2. Disconnect the corrugated upper airway from the clear tube extending from the head of the
manikin.
3. Remove the existing head by turning it face down, aligning the keyways, and pulling it free from
the torso.
4. Install the “Airway Larry” Airway Management Trainer Head using the same method as removing
the head. When inserted at the shoulders, tip the head upward slightly until the two keyways on the
back of the neck slide under the ring and into the top of the torso. (See Figure 4.)
5. Install the CPARLENE
®
Airway to the “Airway Larry” Airway Management Trainer Head by first
connecting the remaining upper airway (corrugated tubing system) to the left bronchus.
6. Use 2 of the supplied red caps to plug the right bronchus and esophagus. (See Figure 5.)
7. Replace the longer exhaust tubing portion of the lower airway through the hole on the inside of the
torso. (See Figure 6.)
8. Replace the compression springs and upper compression plate.
Figure 3 Figure 4
Figure 5 Figure 6
9. Insert the short section of the upper airway through the hole in the upper compression plate and
reattach the lung bag. (See Figure 7.)
10. The lung bag will lay flat on top of the upper compression plate. (See figure 8.)
11. Replace the chest plate and chest skin taking care not to pull the skin too tightly across the torso,
as this may inhibit chest rise during proper ventilation.
Figure 7 Figure 8
D. Replacing Head of CRiSis™Manikins with “Airway Larry” Airway Management
Trainer Head
1. Remove the chest skin and chest plate. Note: Caution should be taken not to damage defibrillation
electronics connected to the chest skin.
2. Disconnect the lung bags from the corrugated bronchus tubes and set aside for future use.
3. Push the bronchus tubes down through the hole in the upper compression plate.
4. Remove the upper compression plate and compression springs.
5. Remove the corrugated bronchus tubes from the airway extending from the existing head and set
aside for future use.
Figure 9
6. Loosen the pinch clamp on the esophagus and pull the stomach tube free from the esophagus
extending from the existing head and set aside for future use.
7. Remove the existing head by turning it face down, aligning the keyways, and pulling it free from the
torso.
8. Install the “Airway Larry” Airway Management Trainer Head using the same method as removing
the head. When inserted at the shoulders, tip the head upward slightly until the two keyways on the
back of the neck slide under the ring and into the top of the torso. (See Figure 4.)
9. Replace the corrugated bronchus tubes. (See Figure 9.)
10. Replace the stomach tube into the esophagus and tighten the pinch clamp. (See Figure 9 inset.)
11. Replace the compression springs and upper compression plate.
HC190001INM8.indd 7-8 1/15/19 2:05 PM

6 3
SETUP
The “Airway Larry” Airway Management Trainer Head is ready to use as a stand-alone trainer upon
delivery. Simply remove it from the carton and unwrap the packaging material. Please note that lung and
stomach bags are not included, but can be purchased separately. See Supplies and Replacement Parts
for part numbers.
LUBRICATION
Before using the Airway Management Trainer, lubricate both the simulator and supplies being used with
the Nasco lubricant provided. (See Figures 1 & 2.)
GENERAL INSTRUCTIONS FOR USE
A. Intubating the Airway Management Trainer
Nasco recommends the use of a 7.5-8 mm endotracheal tube for oral intubation and 7.5 cm or
smaller for nasal intubation. This simulator allows for the Sellick’s Maneuver of applying cricoid pres-
sure during intubation procedures. Ensuring the cuff is properly deflated prior to removal will prolong the
useful life of your simulator. Damage caused by improper use of the simulator will not be covered under
the warranty.
1. Determine the method of intubation.
2. Select the appropriate sized intubation appliance.
3. Generously lubricate the airway and appliance.
4. Intubate the manikin.
5. Visualize chest rise or stomach inflation.
6. Ensure the cuff is properly deflated before removing the appliance.
Note: Remove all appliances prior to storage.
B. Using the Combitube (not included)
Thoroughly read and follow the instructions that come with the combitube. The trainer will accept either
a full size or a small adult tube. As with a real patient, it may be necessary to back the tube out if ventila-
tion cannot be established.
Note: Depending on tube placement, the large cuff may not accept the recommended amount of air. In
this case, simply inflate the cuff to its maximum volume (when the plunger stops) and while holding the
plunger down, detach the syringe from the blue print balloon and proceed.
Figure 2Figure 1
E. Attaching to an Airway Management Trainer Stand
1. Remove the existing head by first removing the lung bags. Set them aside for future use
2. Loosen the pinch clamp on the esophagus and remove the stomach. (See Figure 11.)
3. Turn the existing head until the keyways on the neck and the stand’s head ring attachment align
and you are able to remove the head completely.
4. Lift the head ring attachment on the stand and slide the airway tubes of the new head through the
hole aligning the keyways on the neck to the ring attachment. (See Figure 12.)
5. Slide the head into place and twist to misalign the keyway and return the face to its upward
position.
6. Replace the lung bags and stomach bag, tightening the pinch clamp around the esophagus to
secure the stomach bag. (See Figure 13.)
Figure 11
Figure 12 Figure 13
Figure 10
12. Insert the corrugated bronchus tubes up through the hole in the upper compression plate and
connect the bifurcated lung bags. (See Figure 10.)
13. Replace the chest plate and chest skin, taking care not to pull the skin too tightly across the torso
as this may inhibit chest rise during proper ventilation.
CARE AND MAINTENANCE
A. General Cleaning
Normal surface soil can be removed from the trainer with mild soapy water. Do not allow water to con-
tact electrical components. Stubborn stains may be removed with Nasco Cleaner (LF09919U). Simply
apply the Nasco Cleaner to the soiled area and wipe clean with a soft cloth.
Note: Avoid using cleaner around the mouth area if students will be applying direct mouth-to-mouth
resuscitation techniques, as the cleaner may be toxic if ingested.
HC190001INM8.indd 5-6 1/15/19 2:04 PM

2 7
ABOUT THE SIMULATOR
The Life/form®“Airway Larry” Airway Management Trainer Head is a realistic simulator available
for the training of intubation and other airway management skills. The airway management trainer is
anatomically correct in respect to both size and detail. Landmarks include nostrils, teeth, tongue, oral
and nasal pharynx, larynx, cricoid ring, epiglottis, arytenoid, false and true vocal cords, trachea, and
esophagus.
Nasco’s “Airway Larry” allows you to practice oral, digital, and nasal intubation. E.T., E.O.A., P.T.L.®,
L.M.A., E.G.T.A., Combitube®, and King System insertion can all be practiced as well (please see section
titled “Using the Combitube®”). Suction techniques and proper cuff inflation can also be performed and
evaluated.
In addition, this model also allows students to apply cricoid pressure during the intubation procedure
(Sellick’s Maneuver). By locating the larynx and depressing the cricoid ring, the student may realistically
lower the vocal cords farther into the field of view. This also effectively closes off the esophagus of the
simulator.
Install your new “Airway Larry” Airway Management Trainer Head to update any CPARLENE® mani-
kins and torsos, use as a stand alone trainer, or as a replacement head for any Adult CRiSis™manikin,
torso, or Airway Management Trainer with stand. With proper care, your Life/form®Airway
Management Trainer will provide years of valuable service. Please review the instructions carefully for
setup, cleanup , and maintenance procedures.
LIST OF COMPONENTS
A. “Airway Larry” Airway Management Trainer Head
B. 8-oz. Bottle of Lubricant
C. 3 Red Caps
A.
B.
C.
Actual product may vary slightly from photo. Nasco reserves the right to change product color, materials,
supplies, or function as needed.
Figure 15
Figure 14
B. Cleaning the Airway Management Trainer Head
1. Remove the head from the torso or stand using the same methods previously described. Also
remove the lungs and stomach.
2. Take the trainer to an area with a sink and open counter space. Using the red caps supplied, plug
the right and left bronchi and the esophagus.
3. Stabilize the head on the counter face-up (towels work well for this) with plugged tubes hanging
over the sink. (See Figure 14.)
4. Carefully pour warm soapy water (a mild dish soap works best) into the mouth until the water level
reaches halfway up the tongue.
5. Tilt the head back and bring the neck up 3" off the countertop.
6. Continue filling until the water level covers the tongue. Take a small soft brush and gently scrub the
inside of the mouth (a small toothbrush works well for this). Cotton swabs can be used to scrub
inside the nostrils.
7. When done, pull the red cap from the esophagus and drain the water into the sink.
8. Now pick the head up, hold it in a vertical position, and pull the caps from the bronchi to completely
empty the system. (See Figure 15.)
9. Rinse the airway, following the same procedure used to clean, with warm tap water only. Repeat
this process until all the soap has been flushed from the system.
C. Disinfecting the Airway
To disinfect, repeat the standard cleaning procedure with a bleach solution, as specified by the Centers
for Disease Control.
1. Fill the system with the solution until it reaches the corners of the mouth. Remember to start filling
with the head flat and finish with he neck slightly elevated to ensure that the solution completely fills
all airway passages.
2. Once completely filled with the bleach solution, allow the head to sit for at least 10 minutes.
3. Drain as previously described and repeat the rinsing process to flush out all of the bleach solution.
Set the head aside and allow it to air dry completely prior to next use or storage.
CAUTIONS
• Do not place simulator in contact with any printed paper or plastic. The ink will transfer and cause
an indelible stain. Similar inks, such as ballpoint pen, will also cause an indelible stain.
• Do not use Nasco Cleaner (LF09919U) around the nose or mouth of the simulator. The cleaner
may be toxic if ingested.
• Properly lubricate the Airway Management head and intubation appliances.
• Use only Nasco Pump Spray Lubricant (LF03644U) with this simulator. Other lubricants, such as
silicone oil, may cause damage to the airway of the simulator.
• Ensure intubation appliances are used accordingly. Improper use of intubation appliances could
damage the airway of the simulator. Damage to the airway will require the product to be returned
to Nasco for repair.
HC190001INM8.indd 3-4 1/15/19 2:04 PM

Copyright © 1999 HC190001INM8
ONLINE: NascoHealthcare.com
EMAIL: [email protected]
PHONE: [phone]
ADDRESS: 901 Janesville Ave.
Fort Atkinson, WI 53538
HEALTHCARE
HEALTHCARE
“Airway Larry”
Airway Management
Trainer Head
LF03667U
INSTRUCTION MANUAL
WARNING: Products may contain dry natural rubber.
5-Year Warranty
Other Available Simulators
LF03000U CPARLENE
®
Series
LF03601U Adult Airway Management
Trainer with Stand
LF03602U Adult Airway Management
Manikin
LF03609U Child Airway Management
Trainer with Stand
LF03616U Child CRiSis™ Manikin
LF03617U Deluxe Child CRiSis™
Manikin with Arrhythmia Tutor
LF03620U PALS Update Kit
LF03623U Infant Airway Management
Trainer with Stand
LF03632U Child Intraosseous Infusion/
Femoral Access Leg on a Stand
LF03633U Child Airway Management
Trainer Torso
LF03693U Basic Buddy
®
CPR Manikin
LF03699U “Airway Larry” Airway
Management Trainer
LF03709U Infant CRiSis™ Manikin
LF03720U Baby Buddy
®
Infant
CPR Manikin
LF03750U Bariatric CPR Manikin
LF03760U Airway Management/Cricoid
Pressure Trainer
LF03770U Chest Tube
LF03953U CRiSis™ Manikin, Complete
LF03955U Deluxe CRiSis™ Manikin
LF03956U Deluxe “Plus” CRiSis™ Manikin
LF03965U Adult CRiSis™ Auscultation
Manikin
LF03966U Adult CRiSis™ Auscultation
Manikin with ECG Simulator
LF04200U Adult Sternal Intraosseous
Infusion
LF06001U CPR Prompt® Adult/Child
Manikin
LF06012U CPR Prompt® Infant Manikin
LF06200U CPR Prompt® Keychain
Rescue Aid
LF06204U CPR Prompt® Rescue and
Practice Aid
Practice Aid
LF03840U
SUPPLIES AND REPLACEMENT PARTS
LF03605U Replacement Lungs
LF03606U Replacement Stomach
LF03644U Pump Spray Lubricant
LF09919U Nasco Cleaner
LF03214U
HC190001INM8.indd 1-2 1/15/19 2:03 PM