National Vendors shoppertron 431 Manual

This machine has been engineered to our own rigid safety and performance standards. It
has been designed to comply with sanitation and health guidelines recommended by the
Automatic Merchandising Health-Industry Council (AMHIC) and it conforms with all other
NAMA safety recommendations.
This machine has been manufactured in accordance with the safety standards of both
Underwriter’s Laboratories and the Canadian Standards Association. To maintain this
degree of safety and to continue to achieve the level of performance built into thismachine,
it is important that installation and maintenance be performed so as to not alter the original
construction or wiring and that replacement parts are as specified in the Parts Manual. Your
investment in this equipment will be protected by using this Operator’s Guide and the Parts
Manual in your operation, service and maintenance work. By following prescribed proce-
dures, machine performance and safety will be preserved.

ShoppertronTM Operator’s Guide
4310114 Page i July 2003
Table of Contents
Section I. Preparing the Merchandiser for Vending....................... 1
Initial Set-Up...................................................................................... 3
Section II. Programming Operations ............................................... 9
Control Panel Switch Functions Explained...................................... 11
Programming Flow Charts............................................................... 12
Alphabetical Index of Programming Functions................................ 15
Gain Access to the Supervisor Mode .................................... 17
Enter a New Supervisor Code............................................... 17
Enter a New Data Recall Code .............................................. 18
Lock or Unlock Mode or Payout Keys ................................... 19
Set Printer or DEX Options.................................................... 19
Lock or Unlock Data Clearing Access ................................... 20
Select Printer Baud Rate....................................................... 20
Select Display Language....................................................... 20
Select Coin Mechanism and Options .................................... 21
Select Bill Validator and Options........................................... 21
Initial Setup Of Non-Standard Bill Validator ........................... 22
Select Card Reader and Options ........................................... 23
Select Monetary Options ....................................................... 24
Set Up Winner Mode ............................................................. 26
Set Shop Zones..................................................................... 27
Set Number of Compartments ............................................... 28
Set Zone Preference ............................................................. 29
Set View Delay Time............................................................. 29
Set Door Delay Time............................................................. 29
Set Align/No Align Options .................................................... 30
Display Prices........................................................................ 30
Change Temperature ............................................................ 31
Show the Temperature in Standby Mode.............................. 31
Set Defrost Options ............................................................... 32
Turn Tamper Check On or Off ............................................... 33
Check for Tampering............................................................. 33
View Software Version .......................................................... 34
Set the Time.......................................................................... 34
Set Day of the Week, Month, Date, and Year ....................... 34
Set Daylight Savings Option .................................................. 35
Set Time-Of-Day Inhibited Vending....................................... 35
Set Time-Of-Day Free Vending............................................. 35
Set Time-Of-Day Discount Vending ...................................... 35
Time Interval Editing .............................................................. 36
Select an Out-Of-Service Message ....................................... 38
Select a Freevend Message.................................................. 38
Edit Custom Messages .......................................................... 39

ShoppertronTM Operator’s Guide
July, 2003 Page ii 4310114
View Machine Temperature ................................................... 41
Payout Coins......................................................................... 41
Set Prices .............................................................................. 42
View Nonresettable Sales and Vend Data ............................ 42
View Total Paid Sales ............................................................ 43
View Total Paid Sales by Zone.............................................. 43
View Total Paid Sales by Level............................................. 43
View Discount Sales by Time Interval ................................... 44
View Total Paid Vends .......................................................... 44
View Card Reader Paid Sales............................................... 44
View Total Unpaid Sales ....................................................... 45
View Total Unpaid Sales by Zone ......................................... 45
View Total Unpaid Sales by Level......................................... 45
View Free Vends ................................................................... 46
View Winners......................................................................... 46
View Freevend Sales by Time Interval.................................. 46
View Time Data ..................................................................... 47
View Machine ID Number...................................................... 48
Clear All Resettable Data...................................................... 48
Clear Paid Sales Data Only ................................................... 49
Test Vend Selections and Verify Credit Added ..................... 49
Test the Display..................................................................... 49
Download Data To a PDCD ................................................... 50
View Diagnostic Messages.................................................... 50
Set Freevend Options ............................................................ 53
Section III. Routine Service and Sanitation................................... 54
Section IV. Adjustment, Removal, and Replacement Procedures 58

ShoppertronTM Operator’s Guide
4310114 Page 1 July, 2003
Section I. Preparing the Merchandiser for
Vending
OFF
OFF
ON
FOOD
DRUM
˜
STORAGE
AREA
DRIVE MOTOR
ASSEMBLY
˜
HEALTH
CONTROL
T
EMPERATURE
SENSOR
AND
LOAD SWITCH
COIN
BOX
VEND DOOR
FILTER
LINT
SCREEN
ELECTRICAL
PANEL COVER
˜
˜
DOOR
SWITCH
MAIN
POWER
SWITCH
˜
˜
LEVEL 1
LEVEL 9
INTERLOCK
SWITCH
(230V MODEL ONL
Y)
. . . . . . .

ShoppertronTM Operator’s Guide
July 2003 Page 2 4310114
Health Control
T
he Shoppertron merchandiser is
e
quipped with an electronic health
c
ontrol(required by most state and local
h
ealth authorities). The health control
p
revents vending merchandise that
c
ould be spoiled.
T
he merchandiser will automatically go
i
nto an out-of-service mode ( e`Kbo )and
f
ood will not be vended if any of the fol-
l
owing conditions occur:
•
The temperature of the refrigerated
c
abinet does not fall to 41° F (5° C)
w
ithin 30 minutes after the door of the
r
efrigerated cabinet is closed or after a
d
efrost.
•
The temperature of the cabinet rises
a
bove 41° F (5° C) for more than 15
m
inutes without the door of the
r
efrigerated cabinet having been open.
•
For testing purposes, the temperature of the cabinet rises above 41° F (5° C) fo
r
a
t least one second with the refrigerated door open.
W
hen health control is triggered, the display will read qbjmlo^ov=lrq=lc=
pbosf`b . When the monetary door is opened, the message shows e`Kbo , and
t
he date, time, and maximum cabinet temperature reached are displayed. To
r
eset the health control, the refrigerated cabinet door must be opened and close
d
a
gain.
T
he out-of-service condition usually occurs at initial setup. Therefore, National
V
endors recommends the merchandiser be operated with the refrigerated
c
ompartment left empty until the temperature reaches a level low enough to
s
atisfy the health control.
NOTE:Replace U4 asshown:
28PINPART 32PINPART
LIGHTS
1ON-POWER
2SHORTFLASH-OKAY
OTHER-ERROR
12
U4
U4 U4
1571042
CABINET DOOR
(REF)
SERVICE
KEYPAD
BILL
VALIDATOR
(
OPTIONAL)
COIN
MECHANISM
(OPTIONAL)
MONETARY
DOOR
˜
˜
COIN
RETURN
CUP
˜
CONTROLLE
R
ASSEMBLY
˜

ShoppertronTM Operator’s Guide
4310114 Page 3 July, 2003
Initial Set-Up
Unpack And Inspect
1. Carefully remove the merchandiser from its shipping carton and place it on a
level surface.
2. Inspect the outside ofthe merchandiser for dents, scratches, or any damage
resulting from improper handling.
3. Open the monetary compartment. If the merchandiser has the optional door
lock, the key will be in the coin return receptacle.
4. Inspect the inside of the cabinet. Observe the location and position of the
packing material should you need to reuse it. Carefully remove all packing
material.
IMPORTANT
If you saw any damage when you unpacked the merchandiser,
file a claim immediately with the carrier.
5. Instructions for installing the optional Base Plate are included with the Base
Plate Assembly when shipped.
6. Inspect the merchandiser’s electrical connectors and components.
Utility Requirements
This merchandiser is supplied with a service cord for the country of use and is ter-
minated in a grounding type plug. The wall receptacle used for this merchandiser
must be properly polarized, grounded, and of the correct voltage. Operating the
merchandiser from a source of low voltage will VOID YOUR WARRANTY. Each
merchandiser should have its own electrical circuit and that circuit should be pro-
tected with a circuit breaker or fuse conforming to local regulations.
Voltage Check - Place the leads of a voltmeter across the LINE (LIVE) and
NEUTRAL terminals of the wall receptacle. The voltmeter should indicate 110-
130 volts ac for 120 volt,60 Hz locations, or 220-240 volts ac for 230 volt, 50 Hz
locations.
Polarity Check - Place the leads of a voltmeter across the LINE (LIVE) and
GROUND terminals of the wall receptacle. The voltmeter should indicate 110-
130 volts ac for 120 volt,60 Hz locations, or 220-240 volts ac for 230 volt, 50 Hz
locations.
Noise Potential Check - Place the leads of a voltmeter across the NEUTRAL
and GROUND terminals of the wall receptacle. The voltmeter should indicate 0
volts ac. A measurement greater than 1.5-2.0 volts ac could result in problems
for the merchandiser's electronic circuitry caused by electrical noise.
Any deviation from these requirements could result in unreliable performance
from your merchandiser.

ShoppertronTM Operator’s Guide
July 2003 Page 4 4310114
Installation
NOTICE
This merchandiser is intended for INDOOR use only.
CAUTION
Make sure the merchandiser is properly leveled on a flat, solid,
stable floor or base foundation. IF THIS IS NOT DONE,
PERSONAL INJURY AND/OR DAMAGE TO EQUIPMENT
MAY RESULT!
1. Move the merchandiser to the desired location. It may be necessary to
remove the door in order to move the merchandiser through a narrow
doorway. Be careful when disconnecting the wiring harness. To reconnect
wiring, refer to the figure below
2. Position the merchandiser at least 6 inches (15 cm) from any wall.
J59
J59
J124
J124
J95
J95
4319005 HARNESS CAB DC
4319005 HARNES
S
CAB DC
4319011 HARNESS CAB AC
4319011 HARNES
S
CAB AC
J83 PWR TO FAN
J83 PWR TO FAN
LOOSEN SCREWS AND PIVOT
CHASSIS FORWARD TO
ACCESS J83 AND J84
LOOSEN SCREWS AND PIVOT
CHASSIS FORWARD TO
ACCESS J83 AND J84
J84 FLST LT
J84 FLST LT
J82
J82
ORN
ORN
BLK
BLK
RED
RED
BRN
BRN
MOTOR
DIRECTION
CAPACITOR
MOTOR
DIRECTION
CAPACITOR
J58
J58
J81 COMPRESSOR TRIAC
J81 COMPRESSOR TRIAC
RD
RD
GROUND WIRE
GROUND WIRE

ShoppertronTM Operator’s Guide
4310114 Page 5 July, 2003
3. Using a spirit level, adjust the legs with an open end or adjustable wrench
until the merchandiser is level front to back and side to side.
4. For “bank style” installations of multiple merchandisers:
a. Position the first machine in the location, or at the highest spot if the floor
is not level. Extend the leg levelers only as required to level the
machine.
b. Position and level the remaining machines.
5. Make sure the main power switch is set to OFF.
IMPORTANT
Do not apply power to the merchandiser until you have done
the power source checks outlined above. Possible equipment
damage could result from improper supply voltage.
6. Plug in the merchandiser.
7. Turn the main power switch ON and close the cabinet door. The display
lamp will light, and the vent fan motor will run.
Install the Coin Mechanism
WARNING
Make sure the main power switch is
turned OFF before you work on the
merchandiser. Failure to do so
could result in death or injury.
1. Turn OFF the main power switch.
Refer to the instructions provided
with the coin mechanism and
remove the coin validator
assembly.
2. Set any option switches as
desired. On a Mars TRC 6000,
switch 2 should be set to high
quarter sens. (off).
3. Loosen the coin mechanism mounting screws on the merchandiser so they
stand off about 1/8" (0.3 cm).
4. Position the coin mechanism so the three keyed holes fit over the mountin
g
screws. Pull down on the coin mechanism to seat the screws in the
keyways.
5. Tighten the mounting screws and reinstall the coin validator assembly.

ShoppertronTM Operator’s Guide
July 2003 Page 6 4310114
6. The following figure shows a coin mechanism, bill validator, and card reader
connected to one another via an MDB. Some monetary configurations may
not include all of these devices. Connect your coin MDB mechanism as
shown:
7. Turn ON the main power switch. Select the proper coin mechanism as in
"Select Coin Mechanism and Options" on page 21. Press until
the standby message is displayed, then press .
8. Insert enough coins through the coin slot into the coin tubes to more than
coverthe empty sensor. Insert coins oneat a time and ensure they lay flat in
the tubes. The amount of coins you insert is internally recorded.
9. Manually finish filling all the tubes with coins.
10. Visually check the coin tubes to make sure coins are not shingled.
11. Turn OFF the main power switch.

ShoppertronTM Operator’s Guide
4310114 Page 7 July, 2003
Install the Door Lock
There are two optional door locks available from National Vendors:
FLEX-ACE (P/N 9992000)
Corresponding key (P/N 9994000)
VAN LOCK (P/N 3112163)
Corresponding key (P/N 3112164)
Lock and key kit (P/N 3122165)
Install the door lock as follows:
1. Remove the lock spring.
2. Depress the lock pin and push the lock cylinder in the lever until the pin
snaps into place.
3. Test the lock mechanism with the key.
Install the Money Box Lock
Install the optional money box lock as follows:
1. Remove the money box from the merchandiser.
2. Remove the screw, cam, nut, and washer from the lock assembly.
3. Insert the lock into the opening in the money box. Secure with the washer
and nut.
4. Install the cam and secure with the screw.
5. Placethe money box back in the merchandiser and test the lock with thekey
(provided).
LOCK
SPRING
KEY
LOCK
CYLINDER
LEVER
SQUAR
E
HOLE
L
OCK
MONEY
BOX CA
M
SCREW
NUT
WASHER

ShoppertronTM Operator’s Guide
July 2003 Page 8 4310114
Load the Merchandiser
There are two loading modes: The first is Full Shop, in which the entire drum is
loaded. The second is Limited Shop, where only one or two zones of the drum
are loaded. Limited Shop is usually used in smaller locations where all food in the
merchandiser may not be vended before the freshness dates expire. To set the
loading mode, refer to "Set Shop Zones" on page 27. The general loading pro-
cedure is as follows:
1. Adjust the product dividers, if necessary. See "Adjusting the Product
Dividers" on page 58.
2. Set new prices, if desired. See "Set Prices" on page 42.
3. Set discount prices, if desired. See "Set Time-Of-Day Discount Vending"
on page 35.
IMPORTANT
The load switch overrides the Limited Shop mode, which allows
unused zone(s) of the drum to be loaded.
NOTICE
If the drum is loaded with food which is too large for the
compartments, the drum will not rotate properly.
4. Push the loading switch plunger until the drum rotates to the position where
you want to load food items, then release the plunger.
NOTE
You can pull out the loading switch plunger and the drum will
rotate continuously until you push the plunger in to the mid
position.
5. Load the food drum, then repeat step 4 until the drum is loaded.
6. Tell the machine that it is full. Do this by performing the "Check for
Tampering" on page 33.
7. Close the refrigeration door.

ShoppertronTM Operator’s Guide
4310114 Page 9 July, 2003
Section II. Programming Operations
Some setup, test, and maintenance operations are computer controlled. The con-
trol panel switches and the selection panel switches regulate these operations.
The Displays
The 10-character display performs two functions, and is referred to in this book as
"the display":
1. It shows the customer's selection and how much credit is in the machine, as
well as the ready, service, and time of day messages.
2. It provides information and feedback to the service person during
maintenance.
afpmi^v
Control Panel
Selection Panel

ShoppertronTM Operator’s Guide
July 2003 Page 10 4310114
The Function Keys
The keys on the control panel can be used for up to three things:
Other Keys
The MOVEMENT keys on the control panel let you move inside a mode, and back
and forth between modes. To see how these keys let you move around, study the
flow diagram on the next page.
One Last Thing:
CONTINUE at the end of a function means to press until you return to the
standby message.
The up and down arrow keys are your "legs", which let
you move up and down the list of tasks. These keys are
what let you continue from one step to the next in pro-
gramming procedures.
In most instances, this key on the Selection Panel does the same job
as the down arrow key.
This is your "activate" or "choose" key. It "opens a door" to additional
information and lets you begin a programming task once you are
inside of a mode. Sometimes, it is used as a toggle switch to show
you your choices during a programming task.
In most instances, this key on the Selection Panel does the same job
as the EDIT key.
This is your "end" key. Pressing it one or more times will move you
back to the start of the mode, or all the way back to the standby mes-
sage.
T
HE NUMBER
Y
OU MIGHT BE ASKED TO ENTER A
N
UMERICAL VALUE . PRESSING THIS
K
EY WILL ENTER A "5".
THE PRIMARY PURPOSE
THIS IS THE MAIN JOB OF THE KE
Y .
FROM THE STANDBY MESSAGE , IT WIL
L
ALLOW YOU TO ENTER A PROGRAM
-
MING MODE . IN THIS EXAMPLE , YO
U
CAN VIEW STORED SALES DATA .
THE SECONDARY PURPOSE
THIS IS THE KEY ' S " SECOND JOB ". FO
R
EXAMPLE , THIS KEY CAN BE USED T
O
DELETE A CHARACTER WHEN YOU AR
E
EDITING CUSTOM MESSAGES .

ShoppertronTM Operator’s Guide
4310114 Page 11 July, 2003
Control Panel Switch Functions Explained
Each of the control panel switches has one or more jobs to do. This list will give
you a short overview of those jobs.
Press this button to put your machine into the Price Setting mode.
You can see maximum and minimum machine prices, and change
prices for entire machine, entire tray, or individual selection.
Press this button to select the Free Vend modes.
Press this button to view machine temperature, software version
number, status of unsold product in tamper check or prefer max.
Press this button to:
• Select display language
• Select coin mechanism bill vali-
dator, card reader, and options
• Select monetary options
• Set winner feature
Press this button to view total sales and vends by whole machine,
zone, or level. Clear resettable data.
Press this button to:
• Download data into your portable data collection device (PDCD),
OR
• Set printer baud rate, depending upon which device you are using
Press this button to:
• Set number of products per tray
• Set shop zones
• Set zone preference
• Set door and view delays
• Set drum alignment
• Set up tamper protection
Press this button to:
• Set time of day and date
• Select display messages
• Edit messages
• Set up time of day intervals
for inhibit, freevend, and dis-
count vending
Press this button to pay one or more coins from the coin mechanism.
Press this button to see any fault or condition that may place the
machine out of service
Press this button to:
• Perform TEST VENDS
• Test various machine functions • Test displays
Press this button to:
• Enter and change the SUPERVISOR code
• Lock and unlock access to functions

ShoppertronTM Operator’s Guide
July 2003 Page 12 4310114
Programming Flow Charts
After you become familiar with the programming functions, you will be able to per-
form them without using the detailed, step-by-step tables. The following group of
flow charts will give you a quick reference to the functions each key performs. If
you need additional information, just refer to the page shown in the chart.
"Select Coin
Mechanism and
Options" on
page 21
"Select Bill Vali-
dator and Op-
tions" on page
21
"Select Card
Reader and Op-
tions" on page
23
"Select Mone-
taryOptions"on
page 24
Machine
Configuration
Functions
"Set Up Winner
Mode" on page
26
"Select Display
Language" on
page 20
Pricing
"SetPrices"
on page 42
"Set Shop
Zones" on page
27
Product
Configuration
Functions
"Set View Delay
Time" on page
29
"Set Number of
Compartments"
on page 28
"Set Zone Pref-
erence"onpage
29
"Turn Tamper
Check On or
Off" on page 33
"Set Door Delay
Time" on page
29
"Set Align/No
Align Options"
on page 30
View
Diagnostics
"View Diagnostic
Messages" on
page 50

ShoppertronTM Operator’s Guide
4310114 Page 13 July, 2003
Misc.
"Check for Tam-
pering" on page
33
"View Machine
Temperature"
on page 41
"View Software
Version" on
page 34
Tests
"Test Vend
Selections
and Verify
CreditAdded"
on page 49
"Test the Dis-
play"on page
49
"Set Freev-
end Options"
on page 53
Free Vend
Supervisor Functions
"Gain Accessto
the Supervisor
Mode" on page
17
"Enter a New
Supervisor
Code" on page
17
"LockorUnlock
Mode or Payout
Keys" on page
19
"Set Printer or
DEX Options"
on page 19
"Lock or Un-
lock Data
Clearing Ac-
cess" on
page 20
"Payout
Coins" on
page 41
Payout Coins
"DownloadData
To a PDCD" on
page 50
DEX/Printer
"Select Printer
Baud Rate" on
page 20

ShoppertronTM Operator’s Guide
July 2003 Page 14 4310114
"Set the Time"
on page 34
"Set Time-Of-
Day Inhibited
Vending" on
page 35
"Select an Out-
Of-Service Mes-
sage" on page
38
Time of Day
"Set Day of the
Week, Month,
Date, and Year"
on page 34
"Time Interval
Editing" on
page 36
"Set Time-Of-
Day Free Vend-
ing" on page 35
"Set Time-Of-
Day Discount
Vending" on
page 35
"Select a Freev-
end Message"
on page 38
"Edit Custom
Messages" on
page 39
Data
"ViewNonresettable
Sales and Vend Da-
ta" on page 42
"View Total Unpaid
Sales" on page 45
"View Machine ID
Number" on page 48
"View Total Paid
Sales" on page 43
"View Total Paid
Sales by Zone" on
page 43
"View Total Paid
Sales by Level" on
page 43
"View Discount
Sales by Time Inter-
val" on page 44
"View Total Unpaid
Sales by Zone" on
page 45
"View Total Unpaid
Sales by Level" on
page 45
"View Free Vends"
on page 46
"View Winners" on
page 46
"View Freevend
Sales by Time Inter-
val" on page 46
"View Time Data" on
page 47
"ClearAllResettable
Data" on page 48
"Clear Paid Sales
Data Only" on page
49
"View Total Paid
Vends" on page 44
"View Card Reader
Paid Sales" on page
44

ShoppertronTM Operator’s Guide
4310114 Page 15 July 2003
Alphabetical Index of
Programming Functions
Change Temperature ............................................................................ 31
Check for Tampering............................................................................. 33
Clear All Resettable Data...................................................................... 48
Clear Paid Sales Data Only................................................................... 49
Display Prices........................................................................................ 30
Download Data To a PDCD................................................................... 50
Edit Custom Messages.......................................................................... 39
Enter a New Data Recall Code.............................................................. 18
Enter a New Supervisor Code............................................................... 17
Gain Access to the Supervisor Mode .................................................... 17
Initial Setup Of Non-Standard Bill Validator........................................... 22
Lock or Unlock Data Clearing Access................................................... 20
Lock or Unlock Mode or Payout Keys ................................................... 19
Payout Coins......................................................................................... 41
Select a Freevend Message.................................................................. 38
Select an Out-Of-Service Message....................................................... 38
Select Bill Validator and Options........................................................... 21
Select Card Reader and Options........................................................... 23
Select Coin Mechanism and Options .................................................... 21
Select Display Language....................................................................... 20
Select Monetary Options....................................................................... 24
Select Printer Baud Rate....................................................................... 20
Set Align/No Align Options.................................................................... 30
Set Day of the Week, Month, Date, and Year ....................................... 34
Set Daylight Savings Option.................................................................. 35
Set Defrost Options............................................................................... 32
Set Door Delay Time............................................................................. 29
Set Freevend Options............................................................................ 53
Set Number of Compartments............................................................... 28
Set Prices.............................................................................................. 42
Set Printer or DEX Options.................................................................... 19
Set Shop Zones..................................................................................... 27
Set the Time.......................................................................................... 34
Set Time-Of-Day Discount Vending ...................................................... 35
Set Time-Of-Day Free Vending............................................................. 35
Set Time-Of-Day Inhibited Vending....................................................... 35
Set Up Winner Mode............................................................................. 26
Set View Delay Time............................................................................. 29
Set Zone Preference ............................................................................. 29
Show the Temperature in Standby Mode.............................................. 31

ShoppertronTM Operator’s Guide
July 2003 Page 16 4310114
Test the Display..................................................................................... 49
Test Vend Selections and Verify Credit Added ..................................... 49
Time Interval Editing.............................................................................. 36
Turn Tamper Check On or Off............................................................... 33
View Card Reader Paid Sales............................................................... 44
View Diagnostic Messages.................................................................... 50
View Discount Sales by Time Interval................................................... 44
View Free Vends................................................................................... 46
View Freevend Sales by Time Interval.................................................. 46
View Machine ID Number...................................................................... 48
View Machine Temperature................................................................... 41
View Nonresettable Sales and Vend Data ............................................ 42
View Software Version .......................................................................... 34
View Time Data..................................................................................... 47
View Total Paid Sales by Level............................................................. 43
View Total Paid Sales by Zone.............................................................. 43
View Total Paid Sales............................................................................ 43
View Total Paid Vends .......................................................................... 44
View Total Unpaid Sales by Level......................................................... 45
View Total Unpaid Sales by Zone ......................................................... 45
View Total Unpaid Sales ....................................................................... 45
View Winners......................................................................................... 46