Nauticam NA-E2F User manual

NA - E2F
For Z CAM E2-M4/S6/F6/F8 Cinema Camera
PN 16505
User Manual
Housing
N120 Video Housing
Introduction 2
2
3
4
7
8
Package Contents
Important Instructions
Part Names and Functions
Opening the Housing
Closing the Housing
9
15
Preparation for Use
Recommended Accessory
18
19
20
Care/Storage
Warranty
Specications

2
INTRODUCTION
PACKAGE CONTENTS
Thank you for purchasing this Nauticam product.
Before using the product, please read this manual thoroughly to familiarize yourself with full scope of functions on the
product as well as ensuring that you will use the product correctly.
Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Nauticam dealer.
After purchase, we suggest that
you reuse all packaging materials
for future travelling.
NA-E2F
(2 x Handles with Mounting Balls, 1 x Housing Cap,
2 x Stainless Steel Handle Brackets)
Panasonic CR2032 Battery
(pre-installed for Moisture Alarm)
Spare Main O-ring
Padded Travel Case
Lubricant
Allen key set
O-ring Remover Manual Instruction Card

3
IMPORTANT INSTRUCTIONS
Water-tight test of the housing (without
camera inside) before usage is recom-
mended as well as any O-ring renewal
and port change.
Use only Nauticam lubricant on silicone
rubber O-ring.
Discontinue use immediately when there is
a sign of leakage.
Do not expose the housing in direct
sunlight for a prolonged period.
Prevent any sand or dust or water
penetration inside the housing. Be
extra careful when changing lens and
inserting or removing the camera.
This product is not intened for use by
children, or persons with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
are supervised and/or given instruction by
a responsible person concerning use of
the product to ensure that they can use it
safely.
Do not seal the housing when travelling by
air as this may lead to a pressure difference
between the atmosphere and inside the
housing.
Only the accesories specied by
Nauticam must be used. Third-party
accessories may result in malfunctions
or damage to the product.
Do not stretch any O-rings excessively.
Only remove it using Nauticam O-ring
remover.
Do not open the housing in wet or sandy
environment. Protect the housing from
moisture and debris in order to prevent
malfunction or leakage.
1
3
5
7
9
11 12
4
6
8
10
2
Do not attempt to remove parts of the
housing yourself. Repairs must be done
at authorized service centers only.
The housing should be positioned on the a
stable and safe surface on land.

4
A
PART NAMES AND FUNCTIONS
Fn1 button Fn2 button
IRIS + button IRIS - button
Playback button M28 Accessory port
REC button
Focus - button
eND - button
M16 Accessory port
Focus + button
eND + button
1 2
3 4
5
7
9
11
6
8
10
12
Rear View
98
10
12
7
11
13
1
6
2
4
3
5
Moisture alarm window
13

5
PART NAMES AND FUNCTIONS
LCD Window
ISO/FN button
OK button
1/4”-20 size mounting threads
EV / Down button
M16 Accessory port
Port lock safety button
Port index mark
Menu button
2x M16 Accessory ports
Zoom knob LOCK lever
Port locking lever
Focus knob LOCK lever
Power button
Shutter / Up button
Fn3 button
1
5
9
2
6
10
3
7
11
13
15
4
8
12
14
16
Top + Front Views
16
6
7
9
10
11
15
8
3
2
1
5
13
14
12
4

6
PART NAMES AND FUNCTIONS
Back + Side Views
2
1
34
5
Focus knob Housing unlock button
1/4” Threaded tripod holes
Zoom knob
Zinc Anodes
3
1
4
5
2

7
OPENING THE HOUSING
1
2
3
depress housing unlock button
turn housing lock latch
anti-clockwise to open the
housing
flip open the back housing
when lock latch is aligned to
‘open’ position
* drawings as illustrations only

8
CLOSING THE HOUSING
1
2
3
before closing the housing, clean
and lubricate the main O-ring
make sure nothing is caught
between front and back housing
and that they are fully aligned
before locking
main O-ring
insert the housing shaft into the
shaft hole and then rotate the lock
latch clockwise until you hear and
feel it click into place
housing locked in place securely
* drawings as illustrations only

9
PREPARATION FOR USE
Installing the Camera
1
4
2
3
unlock camera tray lever and
remove the tray from the housing
slide the camera tray back into
the housing along the tray rail
attach the camera tray by tightening
the tray screw into the tripod socket
of the camera
turn zoom and focus knob lock
levers to REL positions.
* drawings as illustrations only

10
PREPARATION FOR USE
Installing the Camera
5
6
* drawings as illustrations only
Place the zoom and focus knobs
in place by turning the knob lock
levers and make sure it is
engaged with lens gears
lock camera tray
Then, connect LANC control cable