Nav TV NNG-Honda 3 User manual

NNG-Honda 3
Navigation interface for New Honda Accord/Odyssey
NTV-KIT555/584
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
1 | P a g e
This is a NEW VERSION (HONDA 3) for Honda Accord and Odyssey.
Please pay attention to this installation guide as MOST COMPONENTS
HAVE CHANGED. DO NOT MIX WITH COMPONENTS FROM
PREVIOUS VERSION AS DAMAGES MIGHT OCCUR.
WARRANTY DISCLAIMER NOTICE! Radio removal, disassembly, installation of
Navigation Electronics, and Radio re-assembly / re-installation is the responsibility of
the installer. It is recommended that you contact a professional installer that is
experienced with proper work methods involving electronics and knowledgeable of
specific procedures for radio disassembly, Navigation Electronics installation, and re-
assembly / re-installation of the Radio Head Unit in the vehicle. INSTALLATION
DAMAGE TO THE VEHICLE RADIO HEAD UNIT IS EXPRESSLY NOT
COVERED UNDER THE PRODUCT WARRANTY.
To avoid dangerous distractions that may lead to an accident, the driver should never
operate the system while the vehicle is in motion. Before installing the product, the
seller should inform the end-user of proper use and compliance with the proper
instructions and all states and federal laws.
Before beginning your installation, familiarize yourself with the installation instructions
and the Navigation system components.
CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes
before beginning installation, to avoid unintended air bag deployment. Note and record
any anti-theft radio codes prior to disconnecting.
Honda Navigation Add-on System General Note
1. This is a newer version (HONDA 3) for Accord and Odyssey, please check with
application list for confirmed vehicle before any work.
2. Touch panel part numbers: Accord 2013-2015 #TSACC919
Odyssey 2014-2015 #TSODY951
3. Only one (1) video connection to the side of the factory LCD screen.
DO NOT BE CONFUSED WITH THE PREVIOUS VERSION.
Power connector is connected to Radio 20-pins plug.
4. There are OPTIONAL camera input and camera power for aftermarket camera.
5. Reverse trigger wire is NOT USED for this kit.
6. AD-Key and 3.5mm Audio Out wires are NOT USED.
7. Honda factory display screen is NOT A TOUCH SCREEN. Installer needs to
remove the factory clear panel for completing the installation.
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
2 | P a g e
Review the overall wire connections in the figure above
HONDA-3 Component list
1. GPS Module
2. Main Harness –HONDA3-20PIN **
3. Touch Panel with TP-IN –see touch panel part number for accord / odyssey
4. Display Y Cable –GVIF-03
5. Audio Switch Box
6. Video Switch Box
7. LCD Cable
8. GPS Antenna
** Please see the connection diagram in next page for extra NOT USED wires **
NTV-DOC225
1
2
3
4
6
5
7
8
9
9.Lane Departure Warning Module (optional)

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
3 | P a g e
NTV-DOC225
or - (not used)

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
4 | P a g e
Connect HONDA3-20PIN main T-harness to radio (DO NOT CONNECT DISPLAY Y CABLE
HERE)
Connect Display Y Cable at the side of screen See instruction below for dip switch settings
DIP Switch Settings
1. DIP switches 1 –6 are OFF by default
2. Turn DIP switch 5 to ON if the vehicle has NO side camera (Lane Watch Camera)
3. Turn DIP switch 6 to ON while system is power on for touch screen calibration
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
5 | P a g e
Accord Touch Panel Installation (*beware of the differences from Odyssey)
Remove factory clear lens FIRST, do not reinstall!
Lift clips on top and bottom of the screen housing to remove display screen
Align the supplied touch panel to the top of screen as indicated
Notice the touch panel ribbon cable for Accord is at the TOP of screen.
Using the screen housing to secure the panel (Do not use adhesive tape or glue)
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
6 | P a g e
Odyssey Touch Panel Installation (*beware of the differences from Accord)
Remove factory clear lens FIRST, do not reinstall!
Remove screws from top (2) and behind (4) the display screen to remove screen housing
Remove the frame from screen Place touch panel as indicated
Orient the touch panel as indicated Reinstall the frame and center the panel
Route cable as shown between components Secure the cable at the back of display screen
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
7 | P a g e
GPS Audio Integration for Factory Equipped External Amp
By default, this system is wired for factory radio with internal amp (non-touch screen radio). If
you are installing this system to premium sound radio with touch screen, you will have to do the
following modification to the wiring in order to avoid “pop” and overly amplified GPS audio.
1. Located the factory external amp
For Accord and Odyssey, the external amp is normally located at the upper side of the
PASSENGER kick panel
For Accord Hybrid, the external amp is normally located at the upper side of the
DRIVER kick panel behind the fuse box
2. Cut the 4-pin wire from main harness and leave about minimum 2” wires for future
connections
3. Connect wires as indicated below. Connect the plug with open wires to the Audio Switch
Box
4. Locate the stereo amp connector (18-pin), cut PIN 6 (pink) and PIN 13 (light green) wires
with minimum 2” from the plug
5. Connect wires as indicated below
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
8 | P a g e
NTV-DOC225
BACK-DET (Or)
ACC+ (Black)
Trigger + (Red)
Right Turn Signal - (Green)
'BACK-DET' (Or)
Right Turn Signal
(Or)

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
9 | P a g e
Honda Crosstour LDW and Reverse wires
CROSSTOUR reverse wire at dash fuse box CROSSTOUR right turn wire in steering
column
Honda Odyssey LDW and Reverse wires
ODYSSEY reverse wire at dash fuse box ODYSSEY right turn wire in steering column
NTV-DOC225

Honda Accord 2013-2015 / Odyssey 2014-2015 Installation
10 | P a g e
Trouble Shooting
Please follow all the steps in this installation manual, failure to do so might
void the product warranty and damage the factory radio
Power
Navigation system should have (2) led lights on the module box for
indication of power and data connections.
Display
No Display
1. There are two led lights at the GPS module to indicate data
and power. If led lights are OFF and radio is ON, check the
power fuse inside the black box from the main harness
2. Check all wiring connectors for any loose connection
3. Check all wiring shielding for any damage during the
installation process
4. Check all wiring for any type of damage
5. Check display Y cables for loose, misalignment, or damage
No Touch Response
1. Check NAV mode ONLY for touch responses
2. Check led lights for power and data indications
3. Check Display Switch Box connections for any loose
connection, or damage
No GPS software loaded, touch screen alignment screen occurred
1. Check map SD card at GPS module, see any sign of missing,
loose, pop-out, misalignment, or damage
2. Turn on DIP switch 6 to activate touch panel calibration and
check for improvement
Sound
1. Check all cable for connections to Audio Box for loose, or damage
2. Check software volume settings, ensure volume is not muted
3. Check connections at radio for loose, damaged wires
NTV-DOC225