Nav TV NTV-KIT589 User manual

Jaguar F-TYPE CAM
Dual Camera interface for select ’14+ Jaguar vehicles
NTV-KIT589
BHM
06/03/14
NTV-DOC207
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
2 | P a g e
Overview
Jaguar F-Type CAM interfaces 2 cameras (front & rear) and enables video and navigation control in motion (if
equipped). Forcing either camera to display is activated via the factory touch screen or optional wired inputs.
This interface is currently only compatible with the 2014+ F-Type.
Kit Contents
RVC-JAG Pinouts
PIN #
Description
Color
1
12v (+) constant input
Yellow
2
Input 1 (+): force rear camera
Red
3
Input 2 (+): force front camera
Blue
6
VIDEO OUT RCA
Yellow
7
RCA Shield
Black
8
CAN HI (Radio Side)
White/Green
9
CAN HI (Car Side)
White/Brown
10
Ground (-)
Black
11
Output 1 ACC (+)
White/Red
12
Output 2 REVERSE (+)
White/Blue
15
Front RCA Video IN
White
16
Rear RCA Video IN
Red
17
CAN LO (Radio Side)
Green
18
CAN LO (Car Side)
Brown
F-TYPE CAM Module
NTV-ASY166
Plug & Play T-Harness
NTV-HAR269
SMB-RCA
Adapter
NTV-CAB007
USB Cable (updates)
NTV-CAB009
Camera 8 optional
NTV-KIT509
Wire side
FAKRA-RCA
Adapter
NTV-HAR099
Male-Male RCA
NTV-CON018

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
3 | P a g e
Dash Removal (F-Type)
1. Using a plastic tool, pry up the plastic trim
surrounding the shifter. It is secured with clips
only.
2. Disconnect the cigarette lighter plug and the push button ignition switch plug. It helps to remove the
push button ignition switch and reconnect it to the plug (for testing).

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
4 | P a g e
3. Remove (2x) Torx t20 screws
securing the bottom half of the
climate control.
4. On top of the dash, in front of the
motorized vents, remove the beauty
panel secure by clips with a plastic tool.
5. Remove (2x) Torx t20
screws securing the screen
bezel:
6. Using a plastic tool and hook tool,
carefully pull the trim surrounding
the climate knobs towards you.
This panel must be pulled straight
forwards.

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
5 | P a g e
7. Remove (2x) Torx t20 screws beneath this panel
(not shown).
8. Both the climate control and screen surround should now be
free, remove these and disconnect all associated harnesses.
9. Remove (4x) Torx t20 screws securing the screen.
Disconnect all associated harnesses and set the screen
aside in a safe place.
The connectors being used
for this Install are shown here
(rear of screen):

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
6 | P a g e
Module Installation
1. With the screen removed, locate the main 16-pin
connector that powers the screen. Connect this plug to
the female side of the provided Plug & Play T-Harness.
2. Connect the provided SMB-RCA Adapter to the
screen at the port (typically purple) closest to the
M.O.S.T Fiber Optic connector.
Note: if there is already a connector here, disconnect
it and use the provided SMB Adapter instead.
3. Connect the male end of the provided Plug & Play T-Harness back to the monitor at the 16-pin port.
4. After installing your camera(s), run the signal and power through the car to the radio opening.
5. If only installing a single camera, connect the signal RCA directly to the SMB-RCA
Adapter. When complete, skip to step 7.
Note: if vehicle possess an OEM reverse camera and you’re adding a front camera only, use the
provided Fakra-RCA adapter to retain this camera. See diagram on page 8.

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
7 | P a g e
6. Optional: If installing 2 cameras:
a. Connect the only male RCA from the provided Plug & Play T-Harness to the free end of the
SMB-RCA Adapter (from step 2).
b. Connect the signal from the rear camera to the RCA labeled ‘REAR’ located on the Plug & Play
T-Harness.
c. Connect the signal from the front camera to the RCA labeled ‘FRONT’ located on the Plug &
Play T-Harness.
7. Connect your camera(s) to power. From the F-TYPE module, Output 1 provides 12v (+) accessory. If
using this output for 2 cameras, trigger a relay with this wire instead (output only provides 12v @ 1
amp!).
Note: using an ACC wire to power the camera is required if the user desires forced camera activation.
8. Connect the F-TYPE CAM module to the 18-pin connector located on the Plug & Play T-Harness.
9. Reconnect all remaining connectors to the screen and test for proper operation.

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
8 | P a g e
Installation Diagram

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
9 | P a g e
F-TYPE CAM Operation
Reverse Camera will automatically display whenever the vehicle is placed in reverse.
Video & Nav Control in Motion is always enabled, no user interaction is required. Video’s will playback in any
gear from the DVD player (if equipped) and the USB port.
Force Rear Camera can be activated by sending 12v (+) to INPUT 1 through a toggle switch (not included), or
using the touch screen (detailed below).
Force Front Camera can be activated by sending 12v (+) to INPUT 2 through a toggle switch (not included), or
using the touch screen (detailed below).
Forcing cameras via OEM touchscreen:
1. Select ‘Extra
Features’
2. Select
‘Cameras’
3. Selecting ‘Settings’will bring
you into Force Camera Mode.
Once in Forced Camera Mode, press
the top-middle of the screen to view
front camera, or the bottom-middle of
the screen for rear camera. This action
will flip between both cameras.
To clear, touch where the clear button
is normally (when navigating menus)

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
10 | P a g e

BHM
04/13/15
NTV-DOC207
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
11 | P a g e