Nav TV NNG-HONDA C NTV-KIT599 User manual

3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
NNG-HONDA C
Navigation interface for select Honda vehicles
NTV-KIT599
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
1 | P a g e
Honda C navigation system application guide
2014 –2015 Civic (with factory 7” touch radio)
2014 –2015 Fit (with factory 7” touch radio)
** Honda_C navigation system only compatible to vehicles listed above. All compatible radio
should be factory equipped 7” touch screen radio. **
WARRANTY DISCLAIMER NOTICE! Radio removal, disassembly, installation of
Navigation Electronics, and Radio re-assembly / re-installation is the responsibility of
the installer. It is recommended that you contact a professional installer that is
experienced with proper work methods involving electronics and knowledgeable of
specific procedures for radio disassembly, Navigation Electronics installation, and re-
assembly / re-installation of the Radio Head Unit in the vehicle. INSTALLATION
DAMAGE TO THE VEHICLE RADIO HEAD UNIT IS EXPRESSLY NOT
COVERED UNDER THE PRODUCT WARRANTY.
To avoid dangerous distractions that may lead to an accident, the driver should never
operate the system while the vehicle is in motion. Before installing the product, the
seller should inform the end-user of proper use and compliance with the proper
instructions and all states and federal laws.
Before beginning your installation, familiarize yourself with the installation instructions
and the Navigation system components.
CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes
before beginning installation, to avoid unintended air bag deployment. Note and record
any anti-theft radio codes prior to disconnecting.
This is a general installation guide for navigation system. There will not be any
instruction on dash / radio removal. Please refer to Honda factory service manual
for removing radio from dash.
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
2 | P a g e
1. Carefully remove factory radio from dash
2. Carefully separate the radio front panel from radio chassis
3. Carefully disconnect (2) ribbon cables as shown above
4. Remove (3) screws from factory PCB board as shown above
Insert the supplied ribbon cable to factory PCB board as shown (Noted the metal contact should
face downward)
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
3 | P a g e
1. Route the wide ribbon cables thru the slots of the new supplied PCB board and connect to
new PCB board accordingly as shown
2. Connect the new small ribbon cables from the new PCB board to the factory PCB board as
shown on the right side of image above
3. Re-use the factory screws to secure the new PCB board to the radio panel
Correct orientation of wide ribbon cables Orientation of small ribbon cable connection
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
4 | P a g e
Reuse (3) screws to secure the board Connect the factory small ribbon cable to
the new board
1. Recheck all connections and secure of the board
2. Tape on the supplied plastic protection sheet on top of the PCB board as shown
3. Notice the extension board at the bottom before reinstall the radio chassis
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
5 | P a g e
Carefully reinstall the radio chassis and use the factory screws and tape to secure the
extension board outside of the radio
Refer to the following diagram for wiring connections
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
6 | P a g e
Honda_C wiring schematic
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
7 | P a g e
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
8 | P a g e
Honda_C System with Factory Premium Sound External Amplifier
Please refer to the following modification if vehicle is equipped with factory premium
sound external amplifier
Unwrap the navigation main harness to access the wires illustrated above
Cut and Connect the Gray(+), Gray/Blk(-) and White(+), White/Blk(-) wires as shown
Extend the wires as indicated above to the factory amp location
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
9 | P a g e
Locate factory premium sound external amplifier
Locate driver side door speaker output wires from external amplifier
Connect Audio-IN wires (+pos and –neg) to audio output from factory amplifier
Connect Audio-OUT wires (+pos and –neg) to speaker wires
NTV-DOC224

Honda Civic / Fit 2014-2015 Installation
10 | P a g e
Trouble Shooting
Please follow all the steps in this installation manual, failure to do so might
void the product warranty and damage the factory radio
Power
Navigation system should have (2) led lights on the module box for
indication of power and data connections.
Display
No Display
1. There are two led lights at the GPS module to indicate data
and power. If led lights are OFF and radio is ON, check the
power fuse inside the black box from the main harness
2. Check all wiring connectors for any loose connection
3. Check all wiring shielding for any damage during the
installation process
4. Check all wiring for any type of damage
5. Check display Y cables for loose, misalignment, or damage
No Touch Response
1. Check NAV mode ONLY for touch responses
2. Check led lights for power and data indications
3. Check Display Switch Box connections for any loose
connection, or damage
No GPS software loaded, touch screen alignment screen occurred
1. Check map SD card at GPS module, see any sign of missing,
loose, pop-out, misalignment, or damage
2. Turn on DIP switch 6 to activate touch panel calibration and
check for improvement
Sound
1. Check all cable for connections to Audio Box for loose, or damage
2. Check software volume settings, ensure volume is not muted
3. Check connections at radio for loose, damaged wires
NTV-DOC224