Naxa NCA-614 User manual

MP3 PLAYER
USB/SD /MMC /AUX SLOT
NCA-614
NCA-614
CAR MP3 PLAYER /U SB /S D

14
SPECIFICATION
General
Power Supply Requirements: DC 14.4V , Negative Ground
Maximum Output Power:
Chassis Dimensions: 178 x 130x 50mm (W x D x H)
Tone Controls
Bass (at 100Hz): +10dB / -10dB
Treble (at 10K): +10dB / -10dB
Current Drain: 5A
USB/SD MUSIC Player
Signal to Noise Ratio: More than 60dB
Channel Separation: More than 60dB
Frequency Response: 20Hz - 20KHz
FM Radio
Frequency Coverage (MHz): 87.5 - 107.9MHz
IF : 10.7MHz
Sensitivity (S/N-30dB): 12dBu
Stereo Separation: >30dB
AM Radio
Frequency Coverage (KHz):
530 - 1710 KHz
IF :
Sensitivity (S/N-20dB): 42dBu
7W x 4(CH)
450KHz
Load Impedance:4 ohms
Remarks:
Specifications subject to change without notice
Installation……………………………………………………………………………………………02
Additional information………………………………………………………………………04
General operations………………………………………………………………………………05
Radio operations …………………………………………………………………………………09
USB/SD operations ……………………………………………………………………………10
BLUETOOTH……………………………………………………………………………………………11
Remote control layout……… ……………………………………………………………………12
Specification……………………………………………………………………………………………14
01

13 02
REMOTE CONTROL LAYOUT
Replacing the Battery
When the operational range of the remote control becomes short or non functional while
operating. Replace a new CR2025 battery. Make sure the battery polarity before
replacement.
1.Pull out Battery Holder while pressing the stopper
2.Put the button type battery(+)mark upward into the Battery Holder.
3.Insert the Battery Holder into the Remote control
PRECAUTIONS
Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop. Like an emergency stop.
Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, form the heater, or where it would be
subject to dust, dirt or excessive vibration.
DIN FRONT-MOUNT (Method A)
Installing the unit
1. Dashboard
2. Holder
After inserting the holder into
the dashboard, select the
appropriate tab according to
the thickness of the dashboard
material and bend them
inwards to secure the holder in
(Fig. 1)
place.
3. Screw
INSTALLATION
(Fig. 1)
12
3
Do not expose the equipment to rain or moisture.

12
03
REMOTE CONTROL LAYOUTREMOTE CONTROL LAYOUT
INPUT THE SD CARD
The SD oblique angle keeps
Rightward exposure, put into
the SD slot and press it again
to eject.
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
2.Insert fingers into the groove in the
front of frame and pull out to remove
the frame. (When reattaching the
frame, point the side with a groove
downwards and attach it. )
3.Lever
Insert the levers supplied with the
unit into the grooves at both sides of
the unit and shown in figure until they
click. Pulling the levers makes possible
to remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
the sides of the unit
Fastening the unit to the factory
radio mounting bracket:
1. Select a position where the screw
holes of the bracket and the
screw holes of the main unit
become aligned (are fitted), and
tighten the screws at 2 places on
each side. Use either truss screws
(5 x 5mm) or flush surface screws
(4 x 5mm)
2. Screw
3. Dashboard or Console
INSTALLATION
6. Strap
Be sure to use the strap to
secure the back of the unit in
place. The strap can be bent by
hand to the desired angle.
7. Plain Washer
2
3
2
2
1
3
(Fig.3)
Removing the unit
1
2
3
4
5
6
7
(Fig.2)
1Power Button
Pause/play/ uttonPreset B 1
Intro/Preset Button2
Repeat Playing/Preset Button3
Random/Preset Button4
Preset Button5
Preset Button6
Mute/ Button
Volume Control
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Mode Switch
ST/MO Button
Loudness Button
Scan Button
Display Button
APS/AMS Button
LOC/DX Button
Band/ Switch
Tuning/Selecting Tracks/ F.F / F.R
Select Button
19
ST
LOUDLOC

11 04
ADDITIONAL INFORMATION
BLUETOOTH
1.Pairing connect.
Turn on car unit, put your mobile near the unit, activate your mobile bluetooth
function.Soon the phone will find the new bluetooth device "CAR AUDIO" .
Input the pairing password “8888” and click OK. The phone will prompt the
matching successful.When pairing connection is successful, the LCD will show
BT ON, and the bluetooth logo “ ”will stop flashing .Then you may perform the
bluetooth operation.
REMARK:depend on bluetooth mobile, the bluetooth system support “HSP” “HFP”
“A2DP” and AVRCP bluetooth profile.
2.Handsfree phone service
If your mobile phone has paried with the unit, you can dial calls out through your
mobile phone. The LCD screen will automatically display the caller's number when an
incoming call comes in.
-Press the “BAND” button lightly to accept the call .Then you can talk with the
other party through the mic on the panel.
-Press “MUTE” button lightly to reject the call when call comes in.
-Press “MUTE” button lightly to hang up after you are finished.
3.Advance Audio distributing profile(A2DP) playing.
Through mobile and unit A2DP connection, press “MODE” and turn to A2DP mode
at the same time, the music playing in mobile can turn to the unit audio system play.
“A2DP” will display on LCD.
-Press button “ ”and “ ” in the panel can select the music track.
-Press “ ” button shortly to pause the music playing.
-Press “BAND”(mode) longly to temporarily discommect the bluetooth.
-Press “BAND”(mode) button longly again to reconnect the bluetooth.
4.Phone number book.
This bluetooth system can automatically store incoming call numbers, up to
10 phone numbers.
-Press and hold “MUTE”(mode) button to enter the phone book and press
VOL button to look up the phone number.
-Press “BAND” button once can call out you desired phone number.
5. Interrupt bluetooth connection/reconnection.
Pressing the “BAND” button lightly to interrupt the bluetooth connection when
your are taking a call and the voice can turn to mobile speaker.
Press “BAND” button again to reconnect.
NOTE:Different mobile phone have different responses.We do not guarantee all the
operation of connectable devices.
6. How to delete stored phone number?
The unit can store ten number of missed ,rejected and ANS separately,
and the first number will auto deleted when the 11th number calls.
7.How to use “RECEIVED” “MISSED” “REJECTED” MANU
ANS/AUTO ANS” Functions.
Press MUTE” for 3 seconds to enter into “RECEIVED” “MISSED” “REJECTED” MANU
ANS/AUTO ANS”. Turn VOL button for choosing the telephone number.
“
“ “

10
05
GENERAL OPERATIONS
FRONT PANEL LAYOUT
1.Power Button
2.Volume/Sel Button
3.Mode switch
4.Display Button
5.LCD Display
6.Reset Button
7.Band/ switch
8.Tune Seek & Track forward Button
9.Tune Seek & Track reverse Button
10.Automatically memory storing
11.Play/pause & Preset Button 1
12.Intro & Preset Button 2
13.Repeat & Preset Button 3
14.Random & Preset Button 4
15.Preset Button 5
16.Preset Button 6
17.Release Button
18. Mute / Button
19. SCN Button
20. Remote Control sensor
21. AUX IN JACK
22. USB connecter
23. SD/MMC slot
24. Flashing LED
/ID3 select
2 3 2 4
2 3
4
2 0 2 2
1
5
7
1 01 7
1 8 1 1 1 2 1 3 1 4 1 5 1 6
1 9
21
8
9
SELECT TRACKS
During USB/SD operation, press SEEK " " button or " "
button to move to the previous track or the following track, Track number shows
on display. During /, hold to fast
reverse or fast forward. Music play starts from when you release the button.
Press preset button (15-16):
- MP3 MODE : 10 TRACK UP / DOWN is activated.
When the total track is 10 or less, KEY is inactivated.
(9) SEEK (8)
USB SD SEEK " " (9) button or SEEK " " (8)
RPT
Press preset button (13):Flash play mode : REPEAT ON / OFF is activated.
When REPEAT ON, RPT INDICATOR comes on and repeats
music track.
the current
RDM
During RANDOM ON, RDM INDICATOR is turned on
each track of disc is played in ramdom instead of normal order.
Press preset button (14): and
USB/SD OPERATIONS
USB/SD FLASH MP3 Playing：
PLAY / PAUSE
Press button (11) pause function Music track play time
flashes. Press it again to resume playback, press it more than 1 second is STOP function.
is activated. INDICATOR
INT
Press button (12): During INTRO ON, INT indicator comes on and begins
Playing the first 10sec of each song, until the last song is played. It begins
playing the entire track from where INT started.
Press (15) over 1 sec to previous folder, Press (16) over 1 sec to next folder.
NCA-614
CAR MP3 PLAYER/USB/SD

09 06
GENERAL OPERATIONS
GENERAL OPERATIONS
ON/OFF
SOUND ADJUSTMENT
Turn on (2) can adjust the desired volume quality.
Press SEL button (2) will change in the following order.
Option:
VOLUME
Adjust volume level by using (2) knob. Turn the VOL knob to left to
decrease the sound level, turn the VOL knob to right to increase the sound level.
VOL/SEL
Note: The unit is initially set to volume mode.
VOL BAS TRE BAL FAD
(Volume) (Bass) ( Treble) (Balance)(Fader)
Press VOL/SEL button shortly and turn VOL button to right or left to select different
menu mode.
Press POWER button (1) to turn on the unit. Press it more than 1 second to turn off.
BASS
Press VOL/SEL button(2) one time. Adjust bass level by using VOL/SEL(2) Knob.
TREBLE
Press VOL/SEL button(2) two times. Adjust treble level by using VOL/SEL(2)
Knob
BALANCE
Press VOL/SEL button(2) three times. Adjust sound balance between left and
right speakers by using VOL/SEL(2)Knob .
FADER (optional)
Press SEL button(2) four times. Adjust sound balance between front and rear
speakers by using VOL/SEL(2)Knob.
SELECT MENU
Press VOL/SEL button for several seconds, selecting menu is activated as cyclical
mode of following function for use's selection:
BAS
VOL TRE BAL
SUB ON/OFF
DSP OFFLOUD OFF/ON
STEREO/MONO DX/LOC MUTE OFF
FAD
RADIO OPERATIONS
- Program Scanning
Press AMS(MP3) button (10) shortly to scan preset station. When the field strength
level is more than the threshold level of stop level, the radio is holding at that preset
number for several seconds with releasing mute, then searches again.
STATION STORING
Press preset button (11~16)
RADIO MODE.
M1 ~ M6
- PRESET MEMORY is loaded when key is pressed for less than 1 second.
- PRESET MEMORY is saved when key is pressed for longer than 1 sec.
AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS(MP3) button (10) for several seconds, the radio searches from the
current frequency and checks the signal strength until one cycle search is finished.
And then 6 strongest stations are stored into the corresponding preset number
button.
BAND SELECTION
In tuner mode, press BAND button (7) to select the desired band. The
reception band will change in the following order:
STATION SELECTION
SCAN
Press scan button (19) to search radio station. When a station signal strength
level is more than the level to stop. The radio will playing the station for 5
seconds and the frequency blinking on the LCD at the same time.
Press and hold scan button (19) more than 3 seconds to select the station which
you desired. The radio will start play the station.
STATION SELECTION
During radio mode, Press “SEEK ” or “SEEK ”buttons to
automatically
search a station, Press “SEEK ” or “SEEK ” buttons shortly is operated as
manual turning mode.
more than 1 second

08
07
GENERALOPERATIONS
MUTE OFF/ON
Select “MUTE on ” mode to lower down the speakers output, return to “MUTE OFF”
mode to resume the speakers output.
In Radio mode. Press SEL button for several seconds. LCD will be show from
BEEP ON AREA USA/EUR. At AREA USA/EUR. You can use VOL +/- to select the
AREA frequency.
AREA SETUP
LOCAL RADIO STATION SEARCH
Press SEL button repeatedly to choose LOCAL(DX).Rotate VOL regulator or
press VOL+/- buttons on the RC to switch between LOCAL and DX.When the
LOCAL function is on the local stations.(stations with weak radio)
Press SEL button repeatedly until LOUD ON is displayed.Rotate VOL regulator
on the front panel or press VOL+/VOL- buttons on the RC to select loudness
ON or OFF.
Press SEL button repeatedly until the display shows STEREO (MONO).Rotate
VOL regulator or press VOL+/- buttons on the RC to switch between STEREO
reception and MONO reception.Improvement of reception of distant stations
can be done by selecting mono mode,which may cut down some reception noise.
GENERAL OPERATIONS
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display (5).
DISPLAY
Press DISP button (4) to operate as the conversion of each display mode as follow:
- Time is displayed for 5sec when DISP key is pressed, and it returns to its
previous display unless DISP key is pressed again.
3) From the clock mode, when DISP Key is pressed for longer than 1sec,
clock mode switches to clockAdjusting mode and the clock display
begins flashing.At this time clock or minute can be changed by pressing (+/-),
or the ENCODER VOLUME.
RESET
RESET button (6) is placed on the housing and must be activated with either
a ball point pen or thin metal object. (Do not use sharp object to avoid damaging
the unit.) The RESET button (6) is to be activated for the following reasons:
- Initial installation of the unit when all wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
SELECT MODE
By pressing this button(3) to go to different function mode:
- Tuner (radio)
- USB
To access this mode a USB device must be connected.
- Memory Card
To access this mode you must be have an SD Card inserted .
- AUX input
Mono/Stereo control (in FM radio mode)