NCR 7606-K261 Manual

7606‐K261
2ndHardDiskDrive
(250GB)
KitInstructions
IssueA

Revision Record
Issue Date Remarks
A May 2012 First Issue

1
Introduction
Thiskitcontainsa250GBSATA3GB/sharddiskdrive,HDDbrackets,SATA
BackplaneBoard,andSATAHarnesstoaddasecondHDDtothe7606terminal.
Kit Contents
31250a
SATA HDD
006-8616862 (250 GB)
HDD Bracket
497-0465040
SATA Backplane Board
497-0445542
HDD SATA Harness
497-0446106

2
Installation Procedures
Caution: StaticElectricityDischargemaypermanentlydamageyoursystem.
Dischargeanystaticelectricitybuildupinyourbodybytouchingyourcomputerʹs
caseforafewseconds.Avoidanycontactwithinternalpartsandhandlecardsonly
bytheirexternaledges.
1. TurnOffthepowertotheterminalanddisconnectanyperipheraldevices.
2. Unplugtheterminalʹspowercord.
3. RemovetheBezel.
a. TurntheKeylocktotheunlockedposition.
b. PullthetopedgeoftheBezelawayfromthechassisandthenremoveit.
a. Loosenthethumbscrews(2)thatsecuretheTopCover.
30629
30634
Thumbscrews

3
b. Slidethecovertowardtherearoftheterminaltoremoveit.
4. RemovetheprimaryHDD.SqueezetheReleaseTabsontheHardDriveBracket
andthenslidetheHDDassemblyoutofthechassis.
31260
31261
Primary HDD
Release Tabs

4
5. RemovetheMediaBracketAssembly.
a. PressontheMediaBracketTabonthesideofthechassis.
b. Lifttheassemblypartiallyoutoftheterminal,guidingtheCDROM/DVD
Driveoutoftheopeninginthefrontofthechassis.
30636
Media Bracket Tab
24103a
Media Drive Bracket

5
6. Removetheknockoutforthe2ndHDDfromthechassis.Insertaflatscrewdriver
intotheslotandprytheitupanddowntobreaktheknockoutloose.
7. ConnecttheSecondarySATAHarnesstotheSATA1connectoronthe
Motherboard.
31262
Knockout
30638
SATA5
(Not Used)
SATA4
(CDROM/DVD, Blue Cable)
SATA1
(Secondary HDD/SSD, Red Cable)
SATA0
(Primary HDD, Red Cable)

6
8. Securethecablesinthetiewraplocatedinthebottomofthechassis.
9. InstallthenewSATABackplaneBoardontheMediaBracket(2screws).
10. ConnecttheHDDpoweranddataharnessestotheSATABoard.

24417
SATA Backplane Board
24418
CDROM/DVD Data
(Blue, no metal latch) CDROM/DVD Power
HDD0 Data (Red) HDD0 Power HDD1 PowerHDD1 Data (Red)

7
11. InstalltheMediaBracketAssemblyintothechassis.
Note: BesuretohookthefrontedgeoftheMediaBracketontothemetalcatchon
thefrontofthechassis.
12. PivotthebackoftheMediaBracketdownintothechassisuntilitlatches.

24422
Metal Catch
Turned Over Hook
CD-ROM/DVD Opening

8
13. InstalltheSecondaryHDDintheHDDBrackets.Aligntheextensionsonthe
bracketswiththescrewholesinthenewdriveandslidethebracketstogether.

14. InstalltheHDDsintotheirrespectiveslotsintheterminal.

15. ReplacetheTopCover.
16. ReplacetheBezel.
Note: IfthesecondaryHDDisgoingtobeusedasaRAIDvolumeseetheNCR
RealPOS82xrtUserGuideforinformationaboutinstallingRAID.
30633a
Align the HDD Screw Holes with the Studs in the Bracket
and Snap the New HDD into the Bracket
24420
HDD0
HDD1