NCR Blk7 Manual

Kit Instructions
Peripheral Integration, Blk7, XR6
7603-K507
Issue A

The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR RealPOS is a trademark of NCR Corporation in
the United States and/or other countries. Other product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.
EMail: [e-mail]
Copyright © 2020
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved

iii
Revision Record
Issue Date Remarks
AMay2021 First Issue

iv

7603-K507 Peripheral Integration, Blk7, XR6
The Peripheral Integration kit provides the necessary components for integrating the
keyboard, display, printer, and cash drawer with the NCRRealPOSXR6(7603). This kit
supports NCRUSBBigTicket Keyboard, NCRCompact Alphanumeric POS Keyboard,
or no keyboard configuration.
The Peripheral Integration kit include all the parts needed for integrating most NCR
peripherals with the XR6terminal, with the following important exceptions:
• For a 64-key POS Keyboard, order tray insert 7459-K325 (available in beige only)
• For 719x Thermal Printers, order tray insert or 7606-K323 (Black)
• For a 7199 Thermal Printer, order tray insert 7607-K324 (Black)
• For DynaKey, Touch, and LCD Operator Displays, order swivel mount or 5968-K024
(Black)
• For 597x Customer Displays, order short or long post options (required for remote
or integrated configuration)
Note: For additional configuration guidelines, refer to Installing Peripherals on page12

2 7603-K507 Peripheral Integration, Blk7, XR6
Kit Contents

7603-K507 Peripheral Integration, Blk7, XR6 3
Part Number Description
497-0510707 Kit, Peripheral Integration, Blk7, XR6
1 497-0510492 Chassis, Integration, Blk7, XR8/6
2 497-0509536 Bracket, Integration Mount, XR8/6
3 497-0450626 Cable Cover, 7606, Blk7
4 497-0503922 Tray, Integration, Blk7, 7606
5 497-0503923 Skirt, Swing Arm, Left, Blk7, 7606
6 497-0503924 Skirt, Swing Arm, Right, Blk7, 7606
7 497-0509618 Assembly, Bezel, Integration, Blk7, XR6
8 497-0511268 Bracket, Tray Support, XR8 Integration
9 497-0427333 Customer Display Post, Blk7, 7606
10 497-0427258 Filler Cap For No Customer Display, Blk7, 7606
11 497-0526168 Rubber Foot (6pcs)
12 006-8611339 Screw-Ph Phillips (8-32X.375) (14pcs)
13 006-8624432 Screw, M4X6, Black, Pan, Sems (4pcs)
14 497-0503925 Filler, Compact Alpha With MSR, Blk7, 7606
15 497-0503926 Filler, Compact Alpha Without MSR, Blk7, 7606
16 497-0503927 Plug, Integration Tray, Blk7, 7606
17 497-0509544 Bracket, Power Supply Mount, XR6
18* 006-8623359 Bag, 2X2 Zip Lock (5pcs)
19 497-0457746 Key, 7403
20* 497-0475090 Cbl, 24Vdc Pwr Supply, DC Extension
21 497-0505336 Switching Power Supply External 24V Adapter For 7649 (150W)
22* 497-0511876 Assy Pack- For 7603/7607 Integration Kit
23* 497-0423108 Instructions-Kit (Reference Sheet)

4 7603-K507 Peripheral Integration, Blk7, XR6
Installation Procedures
Installing and using the Peripheral Integration kit involves the following procedures:
1. Assemble the Integration kit. For more information, refer to Assembling the Integration
Kit on the facing page.
2. Install the XR6terminal into the Integration Chassis. For more information, refer to
Installing the Terminal on page8
3. Install the Bezel. For more information, refer to Installing the Bezel on page11
4. Install the peripherals into the Integration Tray. For more information, refer to
Installing Peripherals on page12
5. Install the Cash Drawer. For more information, refer to Installing the Cash Drawer on
page36
6. Install the Swing Arm Skirts. For more information, refer to Installing the Swing Arm
Skirts on page39
7. Install the CableCover. For more information, refer to Installing the CableCover on
page41.

7603-K507 Peripheral Integration, Blk7, XR6 5
Assembling the Integration Kit
1. Attach the six rubber feet to the bottom of the chassis.

6 7603-K507 Peripheral Integration, Blk7, XR6
2. Install the Tray Support Bracket. The side with more Display Pole mounting holes
must be near the back of the chassis.
a. Position the Tray Support Bracket onto the chassis.
b. Align the mounting holes on the bracket with the mounting holes on the chassis,
and secure the bracket using four #8Phillips screws.

7603-K507 Peripheral Integration, Blk7, XR6 7
3. Install the Integration Tray.
a. Position the Integration Tray on top of the chassis and bracket assembly.
b. Align the mounting holes on the tray with the mounting holes on the chassis and
the bracket, and secure the tray using six #8Phillips screws.
Note: To insure proper alignment of the Integration Tray Top, do not fully
tighten the screws until all of them are in place. This allows the Tray Top to be
shifted easily so all screws can be properly seated.

8 7603-K507 Peripheral Integration, Blk7, XR6
Installing the Terminal
1. Assemble the Integration Mount Bracket and the Power Supply Mount Bracket.
2. Mount the XR6terminal onto its mounting bracket.
a. Place the terminal upside down on a flat surface.
b. Position the mounting brackets assembly on top of the terminal.
c. Align the mounting holes on the terminal bracket with the mounting holes on
the bottom of the terminal, and secure using four M4X6 screws.

7603-K507 Peripheral Integration, Blk7, XR6 9
3. Turn the assembly back into its upright position and install the Power Supply Unit
(PSU).
a. Insert the PSU into its mounting bracket.
b. Connect the DC Extension Cable.
• Connect the Molex connector or the extension cable to the Molex connector
of the PSU.
• Connect the DIN connector of the extension cable to the 24V DC-In port of
the terminal.

10 7603-K507 Peripheral Integration, Blk7, XR6
c. Connect the AC Power Cord to the PSU and use a cable tie to secure the cable to
the mounting bracket.
4. Slide the terminal and PSU assembly into the chassis, and tighten the two
thumbscrews to secure the assembly to the chassis.
Caution: Ensure that no cables are pinched.
5. Route the AC Power Cord towards the back and out of the chassis.

7603-K507 Peripheral Integration, Blk7, XR6 11
Installing the Bezel
1. Turn the Key to the unlocked position.
2. Insert the Bezel hooks into their slots on the front of the chassis.
3. Pivot the Bezel upward until it snaps into position.
4. Turn the Key to the locked position.

12 7603-K507 Peripheral Integration, Blk7, XR6
Installing Peripherals
Note: Take note of the following configuration guidelines when installing peripherals:
• When configuring integrated peripherals, always select the shorter option for power
cable and communication cable for the device where available.
• The keyboard well within the Integration Tray is designed so that no special filler
piece or insert is required for configurations with a PC keyboard or no keyboard at
all.
• For configurations without a customer display, a filler cap is included for the
customer display mount in the standard Peripheral Integration kit.
• A keyboard well filler is available (7459-K318 Charcoal Gray) in order to provide a
flush surface for large third-party keyboards that exceed the width of the Integration
Tray.
• The NCR peripherals listed below are physically NOT supported within an
integrated XR6 configuration:
• PS/2 Big Ticket Keyboard
• 5982 6.5" Color LCD VGA Customer Display
• 7162 Impact Printer (no printer, or other third-party printer configurations)
• 2189, 2186, or other cash drawers

7603-K507 Peripheral Integration, Blk7, XR6 13
Installing the Keyboard
Keyboard installation varies depending on the type of keyboard used.
Note: For configurations without a keyboard, refer to No Keyboard on page16
1. Insert the Keyboard Cable into the cable access hole on the front of the Integration
Tray and route it under the Integration Tray.

14 7603-K507 Peripheral Integration, Blk7, XR6
2. Place the Keyboard on the tray and install the appropriate filler.
• For NCR Big Ticket USB Keyboard, no filler is required.
• For NCRCompact Alphanumeric Keyboard with MSR, use the narrow filler
(item #14 on the Kit Contents).
• For NCR Compact Alphanumeric Keyboard without MSR, use the wide filler
(item #15 on the Kit Contents).
• For NCR 64-Key POS Keyboard, use kit 7459-K325.
• For a third-party keyboard, use kit 7459-K318.
3. Connect the Keyboard Cable to the terminal. For more information, refer to
Connecting the Keyboard Cable on the facing page

7603-K507 Peripheral Integration, Blk7, XR6 15
Connecting the Keyboard Cable
The 7603 supports USB and PS/2 type keyboards. See the following examples of
supported configurations.
USB Keyboard and USB Mouse
PS/2 Keyboard and USB Mouse
Note: PS/2 Extension Cables cannot be used on PS/2 Keyboards with a Glide Pad.

16 7603-K507 Peripheral Integration, Blk7, XR6
USB Keyboard w/Glide Pad
No Keyboard
If a keyboard is not used, install the Integration Tray Plug onto the cable access hole on
the front of the Integration Tray.