NCR 7772-K241 User manual

Kit Instructions
Solid State Drive (SSD)
7772-K241/K253/K255
Issue G

ii
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,
and firmware become available. NCR, therefore, reserves the right to change specifications without prior
notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,
consult with your NCR representative or NCR office for information that is applicable and current.
Copyright © 2019–2021
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved
Revision Record
Issue Date Remarks
AJun 2019 First Issue
BNov 2019 Added K255
CJun 2020 Added CX5 (7773) to introduction
Updated illustrations for steps 4 and 5
DAug 2020 Added installation procedure for CX8 (7736)
EJan 2021 Added K256
FAug 2021 Updated PNs for K253 and K255
Removed K256
GDec 2021 Added Warning statement

Solid State Drive (SSD)
This kit provides a Solid State Drive for:
• NCR CX7 All-in-One POS (7772) or NCRCX8 POS(7736)
•7772-K241 – 120GB SSD
•7772-K253 – 240GB SSD
•7772-K255 – 480GBSSD
• NCRCX5 All-in-One POS(7773)
•7772-K241 – 120GB SSD

2 Solid State Drive (SSD)
Kit Contents
Item Part Number Description
7772-K241 120GBSSD
1 006-8627556 Screw, M3x4mm Phillips, Low Profile, Black
2 006-8627411 Storage, Apacer, 120GB M.2 42mm SATA3D NAND
Module
7772-K253 240GBSSD
1 006-8627556 Screw, M3x4mm Phillips, Low Profile, Black
2 006-8628119 Apacer 240GB 4-channel BiCs4 NVMe M.2 Module
(PNPE1B3A)
7772-K255 480GBSSD
1 006-8627556 Screw, M3x4mm Phillips, Low Profile, Black
2 006-8628118 Apacer 480GB 4-channel BiCs4 NVMe M.2 Module
(PNPE1B3A)

Solid State Drive (SSD) 3
Installation Procedure
Warning: Disconnect the AC power cord from the AC outlet and wait 30 seconds
before servicing the terminal.
NCR CX7 All-in-One POS (7772)/NCRCX5 All-in-One POS(7773)
1. Lay the Display face down on a flat surface.
Note: Always use a soft material (cloth, foam) to protect the display screen when
placing the terminal face down.
2. Remove the Cable Cover.
a. Remove the two (2) screws that secure the Cable Cover to the Back Cover.
b. Rotate and unhook the Cable Cover from the Back Cover.

4 Solid State Drive (SSD)
3. Disconnect the Cables.
a. Loosen the thumbscrew of the 180-degree USB-C Cable then disconnect the
Cable.
b. Remove the Ethernet Cable from the Cable Management Hook then disconnect
the Cable.
4. Loosen the two (2) captive screws that secure the Back Cover to the Display.

Solid State Drive (SSD) 5
5. Rotate the Back Cover away from the Display and unhook the Back Cover Tabs.

6 Solid State Drive (SSD)
6. Insert the M.2 SSD at an angle and slide it into the connector.
Note: There are two M.2 Ports on the Motherboard. The primary M.2 SSD should be
installed in the M.2 Port 1, and the secondary M.2 SSD (for dual media) should be
installed in the M.2 Port 2.
7. Secure the M.2 SSD to the Motherboard with a screw.
Note: When installing the secondary M.2 SSD in M.2 Port 2, ensure cables are not
pinched by the SSDand the SSD’s mounting screw.
8. Reinstall the Display Back Cover.
9. Reconnect the 180-degree USB-CCable and Ethernet Cable.
10. Reinstall the Cable Cover.

Solid State Drive (SSD) 7
NCRCX8 POS(7736)
1. Remove the Top Cover. There are two types of Top Covers:
•Top Cover without Duct — Remove the four (4)screws securing the Top Cover
to the chassis.
•Top Cover with Duct
a. Remove the four (4)screws securing the Top Cover to the chassis.

8 Solid State Drive (SSD)
b. Slide the Top Cover in the direction shown.
2. Insert the M.2 SSD at an angle and slide it into the connector.
Note: There are two M.2 Ports on the Motherboard. The primary M.2 SSD should be
installed in the M.2 Port 1, and the secondary M.2 SSD (for dual media) should be
installed in the M.2 Port 2.

Solid State Drive (SSD) 9
3. Secure the M.2 SSD to the Motherboard with a screw.
4. Reinstall the Top Cover.
•Top Cover without Duct – Install the Top Cover on the chassis using four (4)
screws.

10 Solid State Drive (SSD)
•Top Cover with Duct
a. Set the Top Cover on the chassis.
b. Slide the Top Cover in the direction shown to align the screw holes of the Cover
with the screw holes of the chassis.
c. Secure the Top Cover with four (4)screws.