Neat Bar Pro User manual

Neat Bar Pro & Neat Pad
User Manual

Neat Bar Pro
Video conferencing device
Neat Bar Pro packs a stack of tech
into a simple and elegant slimline
device.
It’s capable of driving three large
screens, has two extreme resolution
cameras, a multiple microphone array
and three full-range speakers.
Ideal for delivering superior-quality
audio, video, and other unique
capabilities to your huddle, focus,
meeting, and conference rooms,
Neat Bar Pro comes with a
dedicated Neat Pad controller and
integrated environmental sensors.

Simple
setup
All you need is in the box,
including mounts, cables
and clear instructions. So
it’s easy for anyone to
install and set-up, above or
below one, two or three
screens.
Wall mount
Screen mount
Table stand

Neat Bar Pro
Neat Bar comes with
everything you need to get
started, including cables,
wall mount, screen mount
and table stand.
In the box
Neat Bar Pro: Video conferencing
device
HDMI cable: 6.5t (2m)
Ethernet cable: 9.8t (3m)
Power cord: 9.8t (3m)
Mount adapter, wall mount, screen
mount and table stand
Screws for mounting to the wall are not included. Mounting on a wall should only be performed
by qualified personnel in line with applicable facility and state regulations. The wall and the
mounting equipment must safely withstand the load of the product.
Neat Bar ProMount adapterTable standScreen
mount
Wall mount
Slide the selected
bracket onto the
mount adapter
and secure with
the hex wrench.
4 × M screw (0.94 in / 24 mm) for VESA mount
4 × M screw (0.94 in / 24 mm) for VESA mount
2 × spacer (to secure parallel TV mount)
1 × 5 mm hex key for the screen mount
1 × 2 mm hex key for the mount adapter
2 additional screw bags for dual or triple screen setup
4 × M screw (0.94 in / 24 mm) for VESA mount
2 × 4 × M screw (0.94 in / 24 mm) for VESA mount
4 × spacer (to secure alignment of all screens)

Neat Pad
Screws for mounting to the wall are not included. Mounting on a wall should only be performed
by qualified personnel in line with applicable facility and state regulations. The wall and the
mounting equipment must safely withstand the load of the product.
Neat Pad works as a Controller for Neat
Bar and can also be configured as a
Scheduling Display for the Meeting
Room. It comes with everything you need
to get started, including cables and
mounting options.
In the box
Hook the mount
adapter onto the
wall mount and
secure with the
hex wrench.
Wall mountSide mount Mount adapter Neat Pad
Neat Pad: 8-inch touch screen
2 × Ethernet cable: 9.8t (3m) + 16.4t (5m)
PoE power adapter
Mount adapter, side mount and wall mount
4 × M screw (0.30 in / 7.5 mm)
for the wall mount
3 × M screw (0.19 in / 4.7 mm)
for the side mount
1 × 2.5 mm hex key for the adapters
1 × 2 mm hex key to secure Neat Pad
to the wall mount

Mounting & releasing
Mounting
Slide Neat Bar onto the
selected mounting
option (1). When fully
inserted tilt Neat Bar
back to horizontal and
check if it is secure by
carefully pulling it
towards you.
Releasing
Tilt Neat Bar fully
forward (1). Pull towards
you (2) until the unit
stops and the red
release lever appears
(3). Push the release
lever up and pull Neat
Bar gently of the
mount adapter.

Size & weight
Neat Bar Pro
Neat Pad
35.04 in (890 mm)
3.15 in
(80 mm)
3.15 in
(80 mm)
7.8 in (198 mm)
5 in
(127 mm)
1.7 in
(42 mm)
Width: 35.04 in (890 mm)
Height: 3.15 in (80 mm)
Depth: 3.15 in (80 mm)
Weight: 6.83 pounds (3.1 kg)
Width: 7.8 in (198 mm)
Height: 1.7 in (42 mm)
Depth: 5 in (127 mm)
Weight: 1.15 pounds (520 g)

Setup & connectivity
Setup
Use the provided cables to set up Neat Bar.
Connect the cables according to the illustration.
Cables marked are included. Cables marked
are optional and not required for basic use of
the system.
Requirements for
a complete setup
Display
Internet connection
Video service
Environmental Requirements
Ambient operating temperature:
32° to 95° F (0° - 35° C)
Storage temperature: -4° - 140° F (-20° - 60° C)
Relative humidity: 10% to 90%
Network standby: <W (ater 20 minutes)
Additional Product
Information
htps://neat.no/bar-pro
Neat Bar Pro and Neat Pad - User Manual rev06
AC power
9.8t (3m) Cable
Auxillary port (RJ)
USB-C Debug
Ethernet port
16.4t (5m) Cable
Factory reset buton
Power over Ethernet
(PoE)
Power adapter for AC
Factory reset buton
USB-C
HDMI-out for external screen
The 16.4t (5m) Ethernet
Cable provided is not to
be used for in-wall
installation. In-wall cable
routing should only be
performed by qualified
personnel using
appropriate equipment.
Security lock slot
WiFi
WiFi
HDMI-out for external screen
Ethernet port
9.8t (3m) Cable
HDMI-in for screen sharing
HDMI-out for external screen
6.5t (2m) Cable