NEC N8551-29F User manual

4-651-174-11(1)
N8551-29F
Built-In AIT Auto-Loader Unit
Instruction Manual
Make sure you read this manual before using the product.
After reading this manual carefully, store it in a safe place.

ii
Safety Indications
To use the N8551-29F Built-In AIT Auto-Loader Unit safely, operate the Built-In AIT Auto-
Loader Unit in accordance with the instructions of this manual.
The instruction manual explains which parts of the Built-In AIT Auto-Loader Unit are dangerous,
the types of dangerous situations which may occur if you ignore the instructions, and how to avoid
dangerous situations.
The instruction manual uses the words “WARNING” and “CAUTION” to indicate the degree of
the danger. Each word is defined as below:
WARNING
This symbol indicates the presence of a hazard that may result in
death or severe personal damage if the given instructions are not
strictly followed.
CAUTION This symbol indicates the presence of a hazard that may result in
burn or injury, and property damage if the given instructions are
not followed.
The following three types of symbols (signal marks) are used as indicators of caution and danger.
Each symbol is defined as follows:

iii
Indicates that a dangerous situation may occur
if you ignore the instruction. The symbol
illustration indicates the kind of prohibited
danger.
Indicates that the corresponding action is
prohibited. A picture in the symbol illustrates
the inhibited action.
Indicates enforcement of action. The symbol
illustration indicates the kind of enforced
action. The given action is required to avoid
danger.
Awareness of
caution
Prohibited
Enforcement
(Example)
(Electric shock)
(Example)
(Do not touch.)
(Example)
(Pull plug.)
The marks used in this manual and their meaning are shown below.
Awareness of caution
Indicates that you may receive an
electric shock if this instruction is
ignored.
Indicates that the unit may generate
smoke or catch fire if you ignore
the instruction.
Prohibited
Do not disassemble, repair or
remodel the Built-In AIT Auto-
Loader Unit, as it may cause an
electric shock or fire.
Indicates general things you
should not do.
Enforcement
Pull the Built-In AIT Auto-Loader
Unit power plug from the outlet.
Otherwise, a fire may occur or you
may receive an electric shock.
Operate the Built-In AIT Auto-
Loader Unit in accordance with the
instructions. Otherwise, a fire may
occur or you may receive an
electric shock.

iv
Precautions during Use
- Please read this chapter -
The information required to use the Built-In AITAuto-Loader Unit correctly is described below.
Safety Considerations
To use the Built-In AIT Auto-Loader Unit safely, please read the considerations listed in this
section and fully understand them. For explanations on the symbols, refer to “Safety Indications”
described at the beginning of this manual.
Important
See the instruction manual provided with the basic processing unit on which the N8551-29F Built-
In AIT Auto-Loader Unit is mounted, in addition to the considerations given herein. The basic
processing unit instruction manual describes the precautions to be taken during mounting/
dismounting the options.
WARNING
■Do not disassemble or modify the Built-In AIT Auto-Loader Unit.
Do not disassemble or modify the N8551-29F Built-In AIT Auto-Loader Unit.
If you do so, a fire or you may receive an electric shock.
■Do not use the Built-In AIT Auto-Loader Unit if it emits smoke or a bad, odor
or makes an abnormal noise.
If smoke, odor or abnormal noise is detected, immediately turn off the basic
processing unit and unplug the power cable from the AC outlet. Then, contact
your dealer or the NEC maintenance service company. If a faulty unit is used
continuously, it may cause a fire.
■Do not use the damaged Built-In AIT Auto-Loader Unit continuously.
If the N8551-29F Built-In AIT Auto-Loader Unit is damaged, immediately
turn off the basic processing unit and unplug the power cable from the AC
outlet. Then, contact your dealer or the NEC maintenance service company.
Using such a faulty unit continuously may cause a fire.

v
WARNING
■Do not insert a wire or a metal chip into the Built-In AIT Auto-Loader Unit.
Do not insert a foreign material such as a metal chip or wire into the ventila-
tion port or the cartridge slot, as this may cause an electric shock.
■Do not use the Built-In AIT Auto-Loader Unit at an unsuitable site.
Refer to the instruction manual provided with the basic processing unit and
check that the Built-In AIT Auto-Loader Unit is installed at a suitable site.
Otherwise, a fire and electric shock as well as operational malfunction may be
caused.
■Do not touch the driver with wet hands.
Do not mount/dismount the Built-In AIT Auto-Loader Unit with wet hands, as
this may cause an electric shock.
CAUTION
■Connect the cable correctly.
Connect the cable as explained in "Mounting on the basic processing unit" on
page 7 of this manual.
■Do not bend the cable.
Do not bend, twist, or bind the power and connection cables. Also, do not put
a load on the cable or catch the cable between things. The cable could be
damaged, and this may cause a fire or electric shock.
■Do not connect or disconnect the cable without removing the plug
When connecting or installing the basic processing unit and peripheral
devices, make sure you unplug the power cord that is connected to the basic
processing unit. To avoid electric shock, do not connect or disconnect the
cable while the power cord is plugged in.
■Do not used damaged cables
Before connecting cables, check that the connector is not damaged, the
connector pins are not bent, and that the connector is not dirty. If the connec-
tor is damaged, the pins are bent, or the connector is dirty, the connector may
short and cause a fire.

vi
CAUTION
■Plug-in the connector up to the end.
Plug-in the cable connector firmly up to the end. If you plug-in the connector
halfway, the poor contact causes the Built-In AIT Auto-Loader Unit to be
heated up and may result in a fire. If dust collects on the outlet, it may be
heated when it comes in contact with water drops and cause a fire.
■Do not hold the cable when unplugging it.
Hold the connector head when plugging or unplugging the power cable and
connection cables. The cable may be damaged if it is pulled, which may cause
a fire or electric shock.
■Do not short circuit the connector pins.
This may cause a fire or electric shock.
■Do not mount the Built-In AIT Auto-Loader Unit on a unit other than the
specified one.
If you mount it on an unauthorized unit, a malfunction, fire and electric shock
may be caused.
■Do not block the fan.
Do not block the fan on the rear of the Built-InAIT Auto-Loader Unit. The
inner temperature will rise and may cause a malfunction, fire and electric
shock.
■Do not put water or foreign materials in the Built-In AIT Auto-Loader Unit.
Do not put water/other liquids or foreign materials such as pins and clips in
the Built-In AIT Auto-Loader Unit. This may cause a fire, electric shock or
failure. If such an object is inserted by mistake into the Built-In AIT Auto-
Loader Unit, immediately turn off the power and unplug the power cable from
the outlet. Leave the Built-InAIT Auto-Loader Unit as it is (do not disassem-
ble it) and contact your dealer or the NEC maintenance service company.
■Do not touch the Built-In AIT Auto-Loader Unit during lightning.
If lightning is likely to occur, unplug the power cable from the outlet. If
lightning starts before you have unplugged the power cable, do not touch the
entire unit including the cables. Otherwise, a fire or electric shock may be
caused.

vii
CAUTION
■Do not store the Built-In AIT Auto-Loader Unit in a dusty, humid place.
Do not store the Built-In AIT Auto-Loader Unit in a humid place, for example,
near a hot water supply. If you reinstall the Built-In AIT Auto-Loader Unit, a
fire may be caused.
■Do not use cellular phones or pagers near the unit
Do not use cellular phones or pagers near this unit. Doing so may cause a
machine malfunction.

viii
For Correct Operation
To operate the N8551-29F Built-In AIT Auto-Loader Unit correctly, observe the following points.
For considerations on handling the AIT data cartridge, refer to the chapter “AIT Data Cartridge”.
Main unit
• Set the SCSI ID of the N8551-29F Built-In AIT Auto-Loader Unit so that it is not similar to the
SCSI IDs of other SCSI equipment.
→Otherwise, an operation error will occur.
• Before setting the magazine on the N8551-29F Built-In AIT Auto-Loader Unit, check that four
AIT cartridges are set in the magazine.
→If the magazine in which only three or less cartridges are contained is set, a machine failure
or damage of the backup data may be caused.
• Do not turn off the power to the basic processing unit when the BUSY lamp on the front of the
Built-In AIT Auto-Loader Unit is ON or blinking.
→This may cause a machine failure or damage of the backup data.
• Do not store the Built-In AIT Auto-Loader Unit in a place exposed to direct sunlight.
→The Built-In AIT Auto-Loader Unit may not be able to operate correctly.
• Do not store the Built-In AIT Auto-Loader Unit in a place subject to corrosive gas, chemicals or
splashing of chemicals.
→The Built-In AIT Auto-Loader Unit may get deformed or damaged and may not operate
correctly.
• Do not store the Built-In AIT Auto-Loader Unit in a place subject to strong vibrations.
→This may cause machine failure.
• Do not put a load on the Built-In AIT Auto-Loader Unit when using or storing it.
→ This may cause machine failure.
• Do not store the Built-In AIT Auto-Loader Unit in a place subject to drastic temperature
fluctuations.
→ This may cause machine failure.
• Use the “AIT Data Cartridge (model: AIT2, AIT1)” as the Built-In AIT Auto-Loader Unit data
cartridge.
→ If you use a data cartridge of another make, a read/write error may occur.
• Use the “AIT Cleaning Cartridge” for cleaning the Built-In AIT Auto-Loader Unit.
→ If you use a cleaner of another make, a machine failure may occur.

ix
• Do not move the unit with the cartridges and magazine set.
→If the unit is subject to shock, the unit and cartridges may be damaged.
• Remove the cartridges from this unit when not using it, or before turning off the power.
→Not doing so may shorten the life of your cartridges and cause a machine malfunction.
When using the Built-In AIT Auto-Loader Unit, remove the magazine, or make sure the
cartridge is returned to the magazine before turning off the power.
• Do not leave the cartridges and magazine protruding from the unit’s magazine slot for extended
periods of time.
→This may shorten the life of your cartridges and cause a machine malfunction.
Magazine
• Do not insert the magazine in the Built-In AIT Auto-Loader Unit when a cartridge is ejected
from the magazine slot.
→This will cause machine failure or operation error.
• Do not store the magazine in a dusty, humid place or in a place subject to direct sunlight.
→Data within the data cartridge set in the magazine may be damaged.
• Do not store the magazine in a place subject to drastic temperature fluctuations.
→Data within the data cartridge set in the magazine may be damaged.
• Do not store the magazine in a place subject to strong vibrations.
→The magazine may be damaged and data within the data cartridge set in the magazine may
be damaged.
• Do not store the magazine in a place subject to corrosive gas, chemicals or splashing of chemi-
cals.
→The magazine may get deformed or damaged and may not operate correctly. Data within
the data cartridge set in the magazine may be damaged.
• Store the magazine in the provided case.
→Data within the data cartridge set in the magazine may be damaged.
• Store the magazine in the special magazine case.
→Not doing so may damage the magazine.
• Do not put a load on the magazine when using or storing it.
→Data within the data cartridge set in the magazine may be damaged.

x
• If the magazine write protect plug is set to Write Disabled, data cannot accidentally be written to
the data cartridges inserted in the magazine. (Even if the data cartridge write protect plug is set
to Write Enabled, data cannot be written to the data cartridge if the magazine’s write protect
plug is set to Write Disabled.)
REC
• It is recommended that you should label the magazine so that you can check the contents of the
data cartridge set in the magazine.
• Use the magazine specially designed for the N8551-29F Built-In AIT Auto-Loader Unit.
→If you use a magazine of another make, a read/write error may occur. In addition, data may
be damaged and Built-In AIT Auto-Loader Unit and magazine failure may occur.
Write Enabled Write Disabled
Magazine Case