Ness 101-090 User manual

101-090 101-076 101-080 101-079
Quick Guide
PROX READER / PIN KEYPAD

Hook-up Diagram for Ness Access Contro Modu e for the M1

Enter
Program
mode
Factory Defau t:
1234
Press the # key 4 times
(Transmit LED will turn o and Program LED will turn red.)
Enter your 4-digit installer code (De ault: 1234)
Exit
Program
mode
Press # at any time to exit programming mode
(or i no buttons are pressed it will exit programming mode)
Se ecting keypad transmission format
Note:
Only one
transmission
ormat can be
used at any one
time.
When Using M1:
Press 1 then
option 4.
Or
Press 1 then
option 5, and you
can have a 5 digit
pin or 4 digits
with # at the end.
Enter Programming mode
Press 1 - (the transmit LED will turn red)
Then you need to select a option rom below:
Option
Keypad transmission
format
1 Single Key, 6-Bit Wiegand (Rosslare Format)
2 Single Key, 6-Bit Wiegand with Nibble + Parity Bits
3 Single Key, 8-Bit Wiegand, Nibbles Complemented
4 4 Keys Binary + Facility Code, 26-Bit Wiegand
5 1 to 5 Keys + Facility Code, 26-Bit Wiegand
6 6 Keys BCD and Parity Bits, 26-Bit Wiegand
7 Single Key, 3x4 Matrix Keypad
8 1 to 8 Keys BCD, Clock & Data Single Key
A ter you have made your selection it will then exit programming mode
automatically. - (Transmit LED will turn red)
Examples
If you want to use a 4 digit number as the pin then do the following:
Set the transmission format to option 4 (4 Keys Binary + Fa ility Code, 26-Bit
Wiegand) you would do the following: # # # # 1234 1 4
Or
You may want to enter # at the end of the number then do the following:
Set the transmission format to option 5 (1 to 5 Keys + Fa ility Code, 26-Bit
Wiegand) you would do the following: # # # # 1234 1 5

Set a new
Program
code
Enter Program Mode
Press 3 - (the transmit LED will turn red)
Enter your new 4-Digit programming code
Once your programming code has been entered then it will exit programming
mode automatically. - (Transmit LED will turn red)
C
hanging the faci ity code
Note:
Facility code can
range between
000 - 255
Factory Defau t:
0
Enter Program Mode
Press 4 - (the transmit LED will turn red)
Enter the new 3 digit code you wish to set as the acility code.
Once you have entered the new acility code then it will exit programming mode
automatically. - (Transmit LED will turn red)
Factory Defau t Settings
Warning: This wi erase the entire memory, settings and codes to factory defau t.
Enter Program Mode
Press 0 - (the transmit LED and Program LED will lash red)
Enter Program code to con irm (de ault: 1234)
Entering the wrong program code will exit programming mode and will return to
normal mode and will not erase any memory.
Rep ace a ost
programming
code
Remove power rom the unit
Activate the tamper by removing the reader rom the wall or removing the readers
case.
Apply power to the reader.
You now have 10 seconds to enter programming mode by using the actory
de ault programming code o 1234.

101-090 101-076 101-080 101-079
Quick Guide
PROX READER / PIN KEYPAD

Hook-up Diagram for Ness Access Contro Modu e for the M1

Enter
Program
mode
Factory Defau t:
1234
Press the # key 4 times
(Transmit LED will turn o and Program LED will turn red.)
Enter your 4-digit installer code (De ault: 1234)
Exit
Program
mode
Press # at any time to exit programming mode
(or i no buttons are pressed it will exit programming mode)
Se ecting keypad transmission format
Note:
Only one
transmission
ormat can be
used at any one
time.
When Using M1:
Press 1 then
option 4.
Or
Press 1 then
option 5, and you
can have a 5 digit
pin or 4 digits
with # at the end.
Enter Programming mode
Press 1 - (the transmit LED will turn red)
Then you need to select a option rom below:
Option
Keypad transmission
format
1 Single Key, 6-Bit Wiegand (Rosslare Format)
2 Single Key, 6-Bit Wiegand with Nibble + Parity Bits
3 Single Key, 8-Bit Wiegand, Nibbles Complemented
4 4 Keys Binary + Facility Code, 26-Bit Wiegand
5 1 to 5 Keys + Facility Code, 26-Bit Wiegand
6 6 Keys BCD and Parity Bits, 26-Bit Wiegand
7 Single Key, 3x4 Matrix Keypad
8 1 to 8 Keys BCD, Clock & Data Single Key
A ter you have made your selection it will then exit programming mode
automatically. - (Transmit LED will turn red)
Examples
If you want to use a 4 digit number as the pin then do the following:
Set the transmission format to option 4 (4 Keys Binary + Fa ility Code, 26-Bit
Wiegand) you would do the following: # # # # 1234 1 4
Or
You may want to enter # at the end of the number then do the following:
Set the transmission format to option 5 (1 to 5 Keys + Fa ility Code, 26-Bit
Wiegand) you would do the following: # # # # 1234 1 5

Set a new
Program
code
Enter Program Mode
Press 3 - (the transmit LED will turn red)
Enter your new 4-Digit programming code
Once your programming code has been entered then it will exit programming
mode automatically. - (Transmit LED will turn red)
C
hanging the faci ity code
Note:
Facility code can
range between
000 - 255
Factory Defau t:
0
Enter Program Mode
Press 4 - (the transmit LED will turn red)
Enter the new 3 digit code you wish to set as the acility code.
Once you have entered the new acility code then it will exit programming mode
automatically. - (Transmit LED will turn red)
Factory Defau t Settings
Warning: This wi erase the entire memory, settings and codes to factory defau t.
Enter Program Mode
Press 0 - (the transmit LED and Program LED will lash red)
Enter Program code to con irm (de ault: 1234)
Entering the wrong program code will exit programming mode and will return to
normal mode and will not erase any memory.
Rep ace a ost
programming
code
Remove power rom the unit
Activate the tamper by removing the reader rom the wall or removing the readers
case.
Apply power to the reader.
You now have 10 seconds to enter programming mode by using the actory
de ault programming code o 1234.