Netbiter WS200 User manual

SP1601 rev.4.30
HMS Industrial Networks AB
Box 4126
300 04 Halmstad
Sweden
Phone +46 (0)35 - 17 29 00
Fax +46 (0)35 - 17 29 09
E-mail inf[email protected]
Web www.hms.se
Netbiter® WS200
Installaon Guide
About the Netbiter Cong ulity
The Netbiter Cong ulity is a PC-based conguraon ulity to set TCP/IP network sengs in the Netbiter. The ulity
scans the Ethernet network for connected Netbiter devices and allows the user to set the IP address, net mask,
gateway, DNS and hostname for each unit.
Installaon Procedure
Download and run the self-extracng installaon package Netbiter Cong from hp://support.netbiter.com
Scanning for connected devices
First ensure that the Netbiter units to be installed
are connected on the same Ethernet network
as the PC running Netbiter Cong. Use standard
Ethernet cables, straight-through or crossover.
When the Netbiter Cong ulity is started it will
scan the Ethernet network for Netbiter devices.
All detected devices will be presented in a list in
the main window. To start a new scan for devices,
click the Scan buon.
Changing IP sengs
To change the IP sengs for a detected device, double-click the
device in the list. This opens a dialog in which the required IP
conguraon can be made.
The default password for authencaon of the new sengs is
admin. Clicking Set will cause the Netbiter to reboot, aer which
the new sengs will be enabled.
The new sengs can be tested by opening a web browser and entering the IP address as
congured above. To discover the device’s IP address when using DHCP - start a new scan with
the Netbiter Cong ulity to view the new network conguraon informaon.
IMPORTANT! Do not select the DHCP opon if
there is no DHCP server available on the network.
Conguraon
Technical Data
Power Supply
9-24 V DC (3 W)
Temperature range
Operang: -30°C to +65°C
Storage: -40°C to +85°C
Humidity range
5-95% RH, non-condensing
Mounng opon
DIN rail (EN 50022)
Dimensions (HxWxD)
57,7mm x 70.0mm x 86,0mm
UL 508

LED Name Color Funcon
Module Status OFF No power
Green Steady –Module is running in normal mode
Serial Status Green Flashing – Serial Packet receive
Red Flashing – Serial Packet transmit
Ethernet Acvity Green Flashing – Packet receive
Ethernet Link Green Steady – Ethernet network detected, 10Mbps
Orange Steady – Ethernet network detected, 100Mbps
SNAP ON SNAP OFF
Field wiring terminals shall be connected with minimum wire size 24 AWG.
Pin Descripon
1CD (Carrier Detect)
2Rx (Receive)
3 Tx (Transmit)
4DTR (Data Terminal Ready)
5GND
6DSR
7RTS (Request To Send)
8CTS (Clear To Send)
9RI (Ring Indicator)
Pin Descripon
TD(B) RS-485 Line B/ RS-422 Transmit B
TD(A) RS-485 Line A / RS-422 Transmit A
RD(B) RS-422 Receive B
RD(A) RS-422 Receive A
COM Common
Tx RS-232 Transmit
Rx RS-232 Receive
DI 2 Digital Input 2 + (10-24VDC)
DI 1 Digital Input 1 + (10-24VDC)
COM Digital Input Common
GND 0V / GND
V+ 9 – 24 VDC
Power / IO / Communicaon
Serial Port
DIN Rail Mounng
LED Descripons
Insert SIM card
The SIM card should be pushed into
the slot on the side of the unit, with
the gold plated side oriented as shown
here.
When fully inserted the SIM card will
lock into place.
To extract the SIM card, press again to
release.