NetComm N3G007W User manual

NetComm 3G Wireless Router
N3G007W
User Guide
NetComm
Copyright

The contents of this publication may not be reproduced in any part or as a whole, stored,
transcribed in an information retrieval system, translated into any language, or transmitted in any
form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or
otherwise, without the prior written permission.
Trademarks
All products, company, brand names are trademarks or registered trademarks of their respective
companies. They are used for identification purpose only. Specifications are subject to be changed
without prior notice.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against radio interference in a commercial environment. This equipment can generate, use and
radiate radio frequency energy and, if not installed and used in accordance with the instructions in
this manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause interference, in which case the user, at his own
expense, will be required to take whatever measures are necessary to correct the interference.
FCC COMPLIANCE STATEMENT

Table of Contents
FCC Interference Statement........................................................................................ 2
System Requirements for Configuration................................................................. 4
1. Introduction............................................................................................................. 5
1.1. Connections............................................................................................ 5
1.1.1. Wireless WAN Mobile Broadband Router (Rear View)......... 5
1.1.2. LEDs– Wireless WAN Mobile Broadband Router (Front View)
............................................................................................................................. 6
1.2. Features............................................................................................................ 7
2. Configuring Wireless WAN Mobile broadband Router.................................... 8
2.1. Installation Considerations ......................................................................... 8
2.1.1. Installation Instructions- Get Start Networking.......................... 8
2.1.2. Establish WiFi Connection............................................................. 11
2.2. Using the Configuration Menu.................................................................. 11
2.2.1. Wizard setting.................................................................................... 14
2.2.2. Advanced Setup > Basic Setting.................................................. 22
3. Troubleshooting....................................................................................................... 54
4. Technical Specifications ....................................................................................... 58

Package Contents
Importance: Check your product package contents FIRST.
The Wireless WAN Mobile Broadband Router package should contain the items listed
below. If any of the items are missing, please contact your reseller.
items Description Quantity
1 Wireless WAN Mobile
Broadband Router 1
2 RJ-45 Cable 1
3 Power adapter 5V 3.0A 1
4 Quick Installation Guide 1
5 CD 1
6 Cradle set 1
7 Rubber pad and Sponge 1
Caution: Using a power supply with a different voltage rating than the one included with
the Wireless WAN Mobile Broadband Router will cause damage and void the warranty for
this product.
System Requirements for Configuration
• A compatible USB 3G modem card with service
Note: Subject to services and service terms available from your carrier.
• Computers with Windows, Macintosh, or Linux-based operating systems with an installed
Ethernet adapter.
• Internet Explorer version 6.0 or Netscape Navigator version 7.0 and above.
WiFi System Requirements

• An 802.11b, 802.11g Adapter, or 802.11n later
1. Introduction
The Wireless WAN Mobile Broadband Router is a high-performance tool that supports wireless
networking at home, work, or in a public place. The Wireless WAN Mobile Broadband Router
supports uses a Type II PC card or USB 3G modem card, either WCDMA or EVDO and even
HSDPA as well, and supports wireless data transfers up to 54 Mbps, and wired data transfers up
to 100 Mbps.
The Wireless WAN Mobile Broadband Router is compatible with industry security features.
1.1. Connections: 3G modem interface depending on the
differenceofmodels
1.1.1.Wireless WAN Mobile Broadband Router (Rear View)
Note:
Contains a reset button to restore the setting back to original factory defaulted setting as if
your convenience of forgetting your applicable setting
Antenna
Auto MDI/MDIX RJ-45 Ports
Automatically sense the types of WAN
and LAN when connecting to Ethernet
Receptor for
Power adapter
Reset Button
Restore to Original
factory defaulted setting
USB port for connecting
with 3G USB modem

1.1.2. LEDs– 3G Wireless WAN Mobile Broadband Router
(Front View)
3G Status LED
A green light as
power is on and
read
y
LAN LED
A green light as connected
to local Ethernet and blinks
durin
g
data is transmission
WAN LED
A green light as
WAN is connected
WiFi LED
A green light as
connection on
WLAN available

1.2. Features
zAutomatic take over back up with 3G connection as Ethernet WAN failover.
zImplementation within 3 minutes allows the network to go where wires cannot go –
even outside the home or office.
zFully compatible with the 802.11g standard to provide a wireless data transfer rate of
up to 54Mbps.
zBackwards compatible with the 802.11b standard to provide a wireless data rate of up
to 11Mbps.
zUtilizes OFDM technology (Orthogonal Frequency Division Multiplexing).
zUser-friendly configuration and diagnostic utilities.
zOperates in the 2.4GHz frequency range.
zAdvanced Firewall features.
zSupports NAT with VPN pass-through, providing added security.
MAC Filtering
IP Filtering
Port Scheduling
zDHCP server enables all networked computers to automatically receive IP addresses.
zWeb-based interface for Managing and Configuring.
zAccess Control to manage users on the network.
zSupports special applications that require multiple connections.
zEquipped with 2*10/100 Ethernet ports, for LAN and WAN access, and USB port for
3G network connection.
zConnects multiple computers to a Broadband either WCDMA or EV-DO even
HSDPA modem to share the Internet connection.
Note: The Wireless WAN Mobile Broadband Router is designed to work with either EVDO
or WCDMA (UMTS) even up to 3.5G HSPA PC interface.
Please refer to your service provider for detailed feature information.

2. Configuring Wireless WAN Mobile broadband Router
2.1. Installation Considerations
The Wireless WAN Mobile Broadband Router allows you access your network using a
wireless connection, from virtually anywhere within its operating range. Keep in mind
however, that the number, thickness, and location of walls, ceilings, or other objects that the
wireless signals must pass through, may limit this range.
Typical ranges vary depending on the types of materials used, and background RF (radio
frequency) noise in your home or business.
To maximize your wireless range, please follow these guidelines:
1. Keep the number of walls and ceilings between the Wireless WAN Mobile Broadband
Router and other network devices to a minimum. Each wall or ceiling can reduce the
Wireless WAN Mobile Broadband Router’s range from 3-90 feet (1-30 meters).
Note: The same considerations apply to your broadband EVDO connection.
2. Keep your product aware from electrical devices (such as microwaves, air conditioners,
and televisions) that emit large quantities of RFI (Radio Frequency Interference).
2.1.1. Installation Instructions- Get Start Networking
Connect the Wireless Router to Your Network
Note: DO NOT connect Wireless WAN Mobile Broadband Router to power before
performing the installation steps below.
1. Attach the antenna.---picture 2.1
Picture 2.1
a. Remove the antenna from its plastic wrapper.
b. Screw the antenna in a clockwise direction to the back panel of the unit.
c. Once secured, position the antenna upward at its connecting joint. This will
ensure optimal reception.

2. Plug in USB modem with service to the Wireless WAN Mobile Broadband Router
---see Picture 2.2
Picture 2.2
Note: The Wireless WAN Mobile Broadband Router is designed to work with
either UMTS or EV-DO and even HSDPA 3G card that can be used as a modem
(support tethered data). Please refer to your service provider for detailed feature
information.
3. Insert the Ethernet patch cable into LAN Port on the back panel of the Wireless
WAN Mobile Broadband Router, and an available Ethernet port on the network
adapter in the computer you will use to configure the unit.-see Picture 2.3
Picture 2.3
Note: The Wireless WAN Mobile Broadband Router LAN Port is
“Auto-MDI/MDIX.” This provides patch Ethernet cable LAN Port access.
4. Connect the power adapter to the receptor on the back panel of your Wireless WAN

Mobile Broadband Router. Then plug the other end of the power adapter into a wall
outlet or power strip.---Picture 2.4
Picture 2.4
a. The Power LED will turn ON to indicate power has been applied.
b. Other LEDs will flash ON and OFF as the Wireless WAN Mobile Broadband
Router performs initialization and Internet connection processes. This will take a
few minutes.
c. When complete, the following LEDs will illuminate green: M1, WAN, LAN, and
WiFi