NETGEAR VEVG2660-1TKSAS User manual

350 East Plumeria Drive
San Jose, CA 95134
USA
October 2014
202-11428-01
VDSL Voice Gateway
Model VEVG2660-1TKSAS
User Manual

2
VDSL Voice Gateway
Support
Contact your Internet service provider for technical support.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc.
and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice.
© NETGEAR, Inc. All rights reserved.

3
Contents
Chapter 1 Hardware Setup
Unpack Your Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Position Your Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cable Your Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2 Connect to the Network and Access the Gateway
Connect to the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wired Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
WiFi Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Types of Logins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Log In to the Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 3 Internet Setup
Use the Internet Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Static IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Manually Specify an Internet Connection with a Login. . . . . . . . . . . . . . . . . . . . 18
Manually Specify an Internet Connection Without a Login . . . . . . . . . . . . . . . . 19
Manually Specify DSL Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specify When to Use DSL and Mobile Broadband Internet Connections . . . . . 22
Change to 3G Broadband Connection Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specify Mobile Broadband Connection Settings . . . . . . . . . . . . . . . . . . . . . . . . . 24
Specify IPv6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 4 Control Access to the Internet
Use Keywords to Block Internet Sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Delete Keywords from the List to Be Blocked . . . . . . . . . . . . . . . . . . . . . . . . . 28
Schedule When to Block Internet Sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Avoid Blocking on a Trusted Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Set Up Security Event Email Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Outbound Firewall Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Add a Custom Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Add Outbound Firewall Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Edit an Outbound Firewall Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Delete an Outbound Firewall Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Set Up a Custom Port Forwarding Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Application Example: Make a Local Web Server Public . . . . . . . . . . . . . . . . . . 36

4
Product Name
How the Gateway Implements the Port Forwarding Rule. . . . . . . . . . . . . . . . . . 37
Port Triggering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Add a Port Triggering Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Specify the Port Triggering Time-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Application Example: Port Triggering for Internet Relay Chat . . . . . . . . . . . . 40
Chapter 5 Share a USB Drive Attached to the Gateway
USB Drive Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Access a USB Drive on the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Map the USB Device to a Windows Network Drive. . . . . . . . . . . . . . . . . . . . . 44
Control Access to the USB Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Use FTP Within the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
View or Change Network Folders on a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . 47
Add a Network Folder on a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Edit a Network Folder on a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Approve USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Safely Remove a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Change the Media Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Chapter 6 Specify Network Settings
View or Change the WAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Default DMZ Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Set Up a Default DMZ Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Change the Gateway’s Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Change the LAN TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Specify the IP Addresses That the Gateway Assigns . . . . . . . . . . . . . . . . . . . . . . 58
Reserved LAN IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Reserve an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Edit a Reserved LAN IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Delete a Reserved LAN IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Use the WPS Wizard for WiFi Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Specify Basic WiFi Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Change the WiFi Security Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Set Up a WiFi Guest Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Control the WiFi Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Use the WiFi On/Off Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Enable or Disable the Wireless Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Specify WPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Set Up a Wireless Card Access List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Set up Dynamic DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
View Devices Currently on the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Custom Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Set Up a Static Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Edit a Static Route. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Delete a Static Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

5
Product Name
Improve Network Connections with Universal Plug and Play. . . . . . . . . . . . . . . 75
Chapter 7 Voice Settings
Specify VoIP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
View the VoIP Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
View the Call Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Chapter 8 Manage Your Network
View Gateway Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
View WAN Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
View WAN Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
View WAN Connection Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Update the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Reboot the Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
View Logs of Gateway Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Control the Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Manage the Gateway Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Back Up the Gateway’s Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . 88
Restore Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Erase the Current Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Change the admin Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Set Up Password Recovery for admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Recover the admin Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Look Up the IP Address for a DNS URL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Display the Gateway’s Routing Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Run the Ping Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Set Up Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Use Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Monitor Internet Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Chapter 9 VPN Lite
VPN Lite Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Configure VPN Lite Sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Chapter 10 Troubleshooting
Access a Forgotten WiFi Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
WiFi Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Changes Not Saved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Troubleshoot with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Apply Power to the Gateway and Check the LEDs . . . . . . . . . . . . . . . . . . . . 104
All LEDs Remain Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Power LED Is Off or Blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Power LED Stays Amber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
DSL LED Is Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
2.4 GHz LED Is Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

6
Product Name
LAN LED Is Off and Ethernet Devices Are Connected . . . . . . . . . . . . . . . . . 106
Cannot Log In to the Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
The Gateway Cannot Access the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Troubleshoot Internet Browsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Troubleshoot a PPPoE Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Troubleshoot Your Network Using the Ping Utility . . . . . . . . . . . . . . . . . . . . . . . 109
Test the LAN Path to Your Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Test the Path from Your Computer to a Remote Device . . . . . . . . . . . . . . . . 110
Troubleshoot IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Problems with Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Appendix A Supplemental Information
Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

7
1
1. Hardware Setup
If you have not already set up your new router using the installation guide that comes in the box,
this chapter walks you through the hardware setup.
This chapter covers the following topics:
•Unpack Your Gateway
•Front Panel
•Rear Panel
•Position Your Gateway
•Cable Your Gateway

Hardware Setup
8
VDSL Voice Gateway
Unpack Your Gateway
Your package contains the following items.
Ethernet cable
Surge protected
Gateway Phone cable
Phone-only filter
You can use the phone-only
filter for any other phone
plugged into the same line
as the DSL modem.
Phone cable
(green port) Splitter/filter
(red and green ports)
power adapter
(white) (grey)
Figure 1. Package contents
Front Panel
The gateway has status LEDs and buttons on the front.
Power LED
Ethernet LAN LED
USB LED
2.4 GHz WiFi LED
Voice LEDs (2)
DSL LED
Internet LED
WPS button
WiFi On/Off
WPS LED
button
Figure 2. Gateway front view

Hardware Setup
9
VDSL Voice Gateway
You can use the LEDs to verify status and connections. The following table lists and
describes each LED and button on the front panel of the gateway.
LEDs and
Buttons Description
Power • Solid green. The gateway has power.
• Blinking green. The gateway is powering on.
• Solid red. The gateway is performing a self-test or the thermal cutoff circuit has been
triggered.
• Off. The gateway is not receiving power or is powered off.
LAN ports • Solid green. The gateway detects an Ethernet connection on one or more LAN ports.
• Blinking green. The gateway is sending data over one or more LAN ports.
• Off. The gateway does not detect Ethernet links on the LAN ports.
USB port • Solid green. The gateway detects an active link on the USB port.
• Blinking green. The gateway is sending or receiving data over the USB port.
• Off. The gateway does not detect a USB device connected to the USB port.
2.4 GHz • Solid green. The gateway detects a 2.4 GHz WiFi connection.
• Blinking green. The gateway is sending data over the WiFi link.
• Off. The wireless radio is turned off and you cannot connect to the gateway with WiFi.
DSL • Solid green. The gateway detects an active link on this port.
• Blinking green. The DSL WAN port is synchronizing with the DSL line.
• Off. The gateway does not detect a link on this port.
Voice 1 and 2 • Solid green. The gateway detects links with telephones on this port.
• Blinking green. At least one telephone is off the hook.
• Off. The gateway does not detect a link on this port.
Internet • Solid green. The gateway is connected to the Internet.
• Blinking green. The gateway is sending or receiving data from the Internet.
• Off. The gateway is not connected to the Internet.
WiFi button Pressing and holding this button for two seconds turns the wireless radio on and off.
WPS button Pressing this button opens a two-minute window when you can use WPS on computers or
wireless devices to connect to the gateway’s WiFi network without typing the WiFi
password. The LED blinks during the two-minute window.

Hardware Setup
10
VDSL Voice Gateway
Rear Panel
The rear panel has the connections and button shown the following figure.
Power adapter input
Ethernet LAN ports
Voice ports (2)
USB port
Power On/Off button
DSL port
Ethernet WAN port
Figure 3. Gateway rear view
Position Your Gateway
The gateway lets you access your network anywhere within the operating range of your
wireless network. However, the operating distance or range of your wireless connection can
vary significantly depending on the physical placement of your gateway. For example, the
thickness and number of walls the wireless signal passes through can limit the range.
Additionally, other wireless access points in and around your home might affect your
gateway’s signal. Wireless access points are gateways, repeaters, WiFi range extenders,
and any other device that emits a wireless signal for network access.
Position your gateway according to the following guidelines:
•Place your gateway near the center of the area where your computers and other devices
operate, and within line of sight to your wireless devices.
•Make sure that the gateway is within reach of an AC power outlet and near Ethernet
cables for wired computers.
•Place the gateway in an elevated location, minimizing the number walls and ceilings
between the gateway and your other devices.

Hardware Setup
11
VDSL Voice Gateway
•Place the gateway away from electrical devices such as these:
-Ceiling fans
-Home security systems
-Microwaves
-Computers
-Base of a cordless phone
-2.4 GHz cordless phone
•Place the gateway away from large metal surfaces, large glass surfaces, and insulated
walls such as these:
-Solid metal doors
-Aluminum studs
-Fish tanks
-Mirrors
-Brick
-Concrete
Cable Your Gateway
You can cable the gateway to a DSL line or to a cable modem.
VDSL
Phone
Line
Figure 4. Gateway cabling diagram
For information about installation, see the installation guide that came in the package with the
product.

12
2
2. Connect to the Network and
Access the Gateway
You can connect to the gateway’s WiFi network or LAN and you can use a web browser to log in
to the gateway to view or change its settings.
This chapter contains the following sections:
•Connect to the Network
•Types of Logins
•Log In to the Gateway

Connect to the Network and Access the Gateway
13
VDSL Voice Gateway
Connect to the Network
You can connect to the gateway’s network through a wired or WiFi connection. If you set up
your computer to use a static IP address, change the settings so that it uses Dynamic Host
Configuration Protocol (DHCP).
Wired Connection
You can connect your computer to the gateway using an Ethernet cable and join the
gateway’s local area network (LAN).
To connect your computer to the gateway with an Ethernet cable:
1. Make sure that the gateway has power (its Power LED is lit).
2. Connect an Ethernet cable to an Ethernet port on your computer.
3. Connect the other end of the Ethernet cable to one of the numbered Ethernet ports on the
rear panel of the gateway.
Your computer connects to the local area network (LAN). A message might display on
your computer screen to notify you that an Ethernet cable is connected.
WiFi Connection
You can connect to the gateway’s WiFi network with Wi-Fi Protected Setup (WPS) or you can
find and select the WiFi network.
To use WPS to connect to the WiFi network:
1. Make sure that the gateway has power (its Power LED is lit).
2. Check the WPS instructions for your computer or wireless device.
3. Press the WPS button on the gateway.
4. Within two minutes, on your computer or WiFi device, press its WPS button or follow its
instructions for WPS connections.
Your computer or wireless device connects to the WiFi network.
To find and select the WiFi network:
1. Make sure that the gateway has power (its Power LED is lit).
2. On your computer or wireless device, find and select the WiFi network.
The WiFi network name is on the product label.
3. Join the WiFi network and enter the WiFi password.
The password is on the product label.
Your wireless device connects to the WiFi network.

Connect to the Network and Access the Gateway
14
VDSL Voice Gateway
Types of Logins
Separate types of logins have different purposes. It is important that you understand the
difference so that you know which login to use when.
These types of logins are associated with the gateway:
•Internet service login. The login that your Internet service provider gave you logs you in
to your Internet service. Your service provider gave you this login information in a letter or
some other way. If you cannot find this login information, contact your service provider.
•WiFi network key or password. Your gateway is preset with a unique wireless network
name (SSID) and password for wireless access. This information is on the gateway label.
•Gateway login.This logs you in to the gateway interface from a web browser as admin.
Log In to the Gateway
When you connect to the network (either with WiFi or with an Ethernet cable), you can use a
web browser to access the gateway to view or change its settings. The first time you access
the gateway, NETGEAR genie automatically checks to see if your gateway can connect to
your Internet service. The next time you access the gateway with a browser, you are
prompted to log in.
To log in to the gateway:
1. Launch a web browser from a computer or wireless device that is connected to the
network.
2. Type http://routerlogin.net or http://10.0.0.2.
A login screen displays.
3. Enter the gateway user name and password.
The user name is admin. The default password is admin. The user name and password
are case-sensitive.

15
3
3. Internet Setup
Usually, the quickest way to set up the router to use your Internet connection is to allow the genie
to detect the Internet connection when you first access the router with a web browser. You can
also customize or specify your Internet settings.
This chapter covers the following topics:
•Use the Internet Setup Wizard
•Static IP Address
•Manually Specify an Internet Connection with a Login
•Manually Specify DSL Settings
•Manually Specify DSL Settings
•Specify When to Use DSL and Mobile Broadband Internet Connections
•Change to 3G Broadband Connection Mode
•Specify Mobile Broadband Connection Settings
•Specify IPv6 Settings

Internet Setup
16
VDSL Voice Gateway
Use the Internet Setup Wizard
The Internet Setup Wizard detects the type of Internet connection and helps you configure
the gateway.
Note: If your Internet service provider assigned you a static IP address (this
is uncommon), see Static IP Address on page 18.
To use the Internet Setup Wizard:
1. Launch a web browser from a computer or wireless device that is connected to the
network.
2. Type http://routerlogin.net or http://10.0.0.2.
A login screen displays.
3. Enter the gateway user name and password.
The user name is admin. The default password is admin. The user name and password
are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup Wizard.

Internet Setup
17
VDSL Voice Gateway
5. Click the Next button.
6. In the Internet Connection Mode drop-down list, select one of the following:
•Use DSL connection first and if fail 3G Mobile Broadband connection
•Always use Mobile Broadband connection
•Always use DSL connection
7. Click the Next button.
8. In the Select Country list, select your country.
9. Leave the Yesradio button selected and click the Next button.
A connection detection progress screen displays. When the gateway detects the
connection, more screens display.
10. When prompted, select your Internet service provider.
11. If your ISP requires login credentials, enter your user name and password and click the Next
button.
The Setup Wizard detects the connection type and displays relevant prompts.
12. Complete the fields for your connection type:
•For a PPPoE or PPoA connection, type the user name and password.
Both are case-sensitive.
•For IP over ATM Classical IP assignment (RFC1577), enter the assigned IP address,
the subnet mask, and the IP address of the primary DNS server for your ISP.
DNS servers translate an Internet name such as www.netgear.com to a numeric IP
address.
13. Click the Test button.
The Setup Wizard checks your Internet connection.
Note: If you have trouble connecting to the Internet, see Chapter 10,
Troubleshooting, for help.
14. After the test succeeds, click the Apply button.
Your settings are saved.

Internet Setup
18
VDSL Voice Gateway
Static IP Address
Internet service with a static IP address is uncommon. If the Setup Wizard detects this type of
Internet connection, you are prompted to enter the following information:
•The Internet service provider’s recommendation for one of these settings:
-Use Static IP Address
-Use IP Over ATM (IPoA — RFC1483 Routed)
•Your assigned IP address, subnet mask, and the IP address of your ISP gateway
•The IP address of your ISP primary DNS server and a secondary DNS server address if
one is available
Your Internet service provider can provide this information to you.
Manually Specify an Internet Connection with a Login
To configure an Internet connection with a login:
1. Launch a web browser from a computer or wireless device that is connected to the
network.
2. Type http://routerlogin.net or http://10.0.0.2.
A login screen displays.
3. Enter the gateway user name and password.
The user name is admin. The default password is admin. The user name and password
are case-sensitive.
The BASIC Home screen displays.

Internet Setup
19
VDSL Voice Gateway
4. Select Internet Setup.
5. In the WAN drop-down list, select a WAN.
6. For the Does your Internet connection require a login? setting, leave the Yesradio
button selected.
7. Complete the fields to specify your Internet connection.
For more information about the settings, see the online help.
8. Click the Apply button.
Your settings are saved.
Manually Specify an Internet Connection Without a Login
To configure an Internet connection without a login:
1. Launch a web browser from a computer or wireless device that is connected to the
network.
2. Type http://routerlogin.net or http://10.0.0.2.
A login screen displays.
3. Enter the gateway user name and password.
The user name is admin. The default password is admin. The user name and password
are case-sensitive.
The BASIC Home screen displays.

Internet Setup
20
VDSL Voice Gateway
4. Select Internet.
5. In the WAN drop-down list, select a WAN.
6. For the Does your Internet connection require a login? setting, select the No radio
button.
7. If your Internet connection requires an account name or host name, type it in the Account
Name (If Required) field.
8. If your Internet connection requires a domain name, type it in the Domain Name (If
Required) field.
For the other sections in this screen, the default settings usually work, but you can
change them. For more information about the settings, see the online help.
9. Complete the fields to specify your Internet connection settings.
10. Click the Apply button.
Your settings are saved.
Note: If you can access websites, but you get errors, it is likely that your
DNS servers are not set up correctly. Contact your Internet service
provider to get the DNS server addresses.
Manually Specify DSL Settings
You can view or change the gateway’s DSL settings.