NETGEAR ReadyNAS Series User manual

Installation
ReadyNAS OS 6 Desktop Storage

2
Contents
Package Contents ....................................................................................................... 3
Basic Setup.................................................................................................................... 4
Reformat Disks............................................................................................................. 9
Additional Information .............................................................................................12

3
Package Contents
Important: Read all safety warnings in the hardware manual for your
system before connecting the system to the power supply.
ReadyNAS system
Ethernet cable Power adapter and power cord
(varies by model)
Bluetooth adapter
(only some models)
See the hardware manual for
your system for installation
and use

4
Basic Setup
Aer you follow these instructions, your ReadyNAS is ready to use in a
production environment. Setup takes approximately 15 minutes.
¾To set up your storage system:
1. Install all available disks that you want to use in your ReadyNAS
system.
Note: If you are using previously formatted disks that contain data,
you must reformat these disks before continuing. See Reformat Disks
on page 9.
For a list of supported disks, see the Hardware Compatibility List at
netgear.com/readynas-hcl.
For information about installing disks, see the hardware manual for
your system or visit
https://www.youtube.com/watch?v=hLiu0VeXd-Y.
2. Place your system in a location that provides adequate ventilation.
High-capacity disks can produce considerable heat. It is important to
ensure that the fan exhausts are unobstructed.
For a complete list of placement considerations, see the hardware
manual for your system.

5
3. Connect the power adapter to the power cord.
4. Connect the power adapter to the back of the system and plug the
power cord into a wall outlet or power strip.
5. Use an Ethernet cable to connect an Ethernet port on the storage
system to your network.
6. If necessary, press the Power button to turn on the system.
7. Wait for the Power LED to turn solid blue or for the status display
screen to display the system’s IP address.
8. Visit readycloud.netgear.com on a computer that uses the same local
area network (LAN) and Internet connection as your ReadyNAS
system.

6
Note: If your computer cannot access the Internet, download and run
the RAIDar utility instead. Download RAIDar to a computer connected
to the Internet and transfer the downloaded file to the computer
on the same LAN as your ReadyNAS system. You can find the latest
version of RAIDar at netgear.com/raidar.
9. Click the Start button for setting up a new ReadyNAS.
10. Click the Discover button.
ReadyCLOUD detects your ReadyNAS system on the network and
displays the New ReadyNAS Discovered page.
11. Click the Setup button.

7
12. Select the mode that you want to use to set up your system:
• Option 1. Select the Setup with ReadyCLOUD (Default) radio
button and do the following:
a. Complete the Create a MyNETGEAR Account fields and
click the Next button, or click the Sign in to an Existing
Account button and sign in to your account.
b. Follow the prompts to configure your ReadyNAS system.

8
• Option 2. Select the Oine Installation (Advanced):
a. Enter admin for the user name, enter password for the
password, and click the OK button.
Note: You can change these credentials when you configure
your system. We recommend that you change your password
as soon as possible.
The ReadyNAS local admin page displays in your browser and
launches a setup wizard.
b. Follow the prompts of the setup wizard to configure your
ReadyNAS system.
The setup process is complete. You can begin using your ReadyNAS
storage system.

9
Reformat Disks
If you are using previously formatted disks that contain data, you must
reformat the disks before you can use them with your ReadyNAS system.
WARNING: This process erases all data and reformats all disks into a
single X-RAID volume. If you want to preserve the data on the disks, you
must back up the data to an external drive before using the disks in your
ReadyNAS storage system.
Note that his procedure returns the storage system to factory default
condition and is not necessary if you are adding or replacing individual
disks, even if the disks were previously formatted. See the ReadyNAS OS
manual, available at netgear.com/support/product/ReadyNAS_OS_6, for
information about formatted disks and already configured systems.
¾To reformat previously formatted disks:
1. If your system is powered on, gracefully power o the system.
See Additional Information on page 12.
2. Install the previously formatted disks.
For a list of supported disks, see the Hardware Compatibility List at
netgear.com/readynas-hcl.

10
For information about installing disks, see the hardware manual for
your system.
3. Using a straightened paper clip, press and hold the Reset button.
4. Press the Power button.
The system powers on.
5. Continue pressing the Reset button until the system enters boot
mode:
• If you are using a 2-bay storage system, the Power, Disk 1, Disk
2, and Backup LEDs light when the system is in boot mode.
• If you are using a 4-bay or 6-bay storage system, the status
display screen indicates that the system is in boot mode.
6. Select the factory default option from the boot menu:
• If you are using a 2-bay storage system, do the following:
a. Scroll through the boot menu options by pressing the
Backup button.
b. When only the Disk 1 LED is lit, press and release the Reset
button.
• If you are using a 4-bay storage system, do the following:
a. Scroll through the boot menu options by pressing the
Backup button.