netvox Z713 User manual

ZigBeeTM- Humidity/ Temperature/ Ultraviolet Sensor
User Manual
Humidity/ Temperature/ Ultraviolet Sensor
Outdoor Type
Model: Z713
20130816
FW V3.1
HW V7.1~V7.2

1
Table of Contents
1. Introduction.............................................................................................................................................................. 2
2. Product Appearance.................................................................................................................................................3
3. Specification.............................................................................................................................................................. 4
4. Installation.................................................................................................................................................................5
5. Setting up Z713......................................................................................................................................................... 6
5-1. Join the ZigBee Network................................................................................................................................ 6
5-2. Binding............................................................................................................................................................6
5-3. Sleeping Mode................................................................................................................................................ 6
5-4. Wake up Z713.................................................................................................................................................7
5-5. Battery............................................................................................................................................................. 7
5-6. Restore to Factory Setting...............................................................................................................................7
6. Home Automation Clusters for Z713..................................................................................................................... 8
7. Important Maintenance Instructions................................................................................................................... 10

2
1. Introduction
Netvox Z713, a humidity/ temperature/ ultraviolet sensor, acts as an End Device in ZigBee network. It does not
perform permit-join function as a coordinator or a router for other devices to join the network. It is used for
detecting ambient and sends the humidity/ temperature/ ultraviolet data to a control center wirelessly.
What is ZigBee?
ZigBee is a short range wireless transmission technology based on IEEE802.15.4 standard and supports multiple
network topologies such as point-to-point, point-to-multipoint, and mesh networks. It is defined for a
general-purpose, cost-effective, low-power-consumption, low-data-rate, and easy-to-install wireless solution for
industrial control, embedded sensing, medical data collection, smoke and intruder warning, building automation
and home automation, etc.

3
2. Product Appearance
Solar Panel Board
UV Sensor
Mount Holder
H/T Sensor
LED Indicator
Binding Key
UV Connector

4
3. Specification
Fully IEEE 802.15.4 compliant
Utilizes 2.4GHz ISM band; up to 16 channels
Power supply: Two 1.5V AA batteries
Operating voltage: 2.3V~3.6VDC
Operating consumption: Up to 40mA
Standby consumption: Up to 0.8uA
Sensing range- temperature: -10℃~50℃; humidity: 5%~95%
Waterproof and suitable for outdoor use
Up to 150 meters wireless transmission range in non-obstacle space
Easy installation and configuration

5
4. Installation
Front view
Remove the
battery
Insert the
batteries
The batteries
are installed
Install the
battery cover
The installation
is completed

6
5. Setting up Z713
5-1. Join the ZigBee Network
After Z713 is turned on, it will search for an existing ZigBee network and send a request to join the network
automatically. While Z713 is under the coverage from a coordinator or a router whose permit-join feature is
enabled, Z713 will be permitted to join the network.
Step1. Enable the permit-join function (valid for 60 seconds) of a coordinator or a router (please refer to
the user manual of the coordinator or the router to enable the permit-join feature).
Step2. Turn on Z713. It will start to search and join the network.
Step3. The indicator will flash 5 times after it is joined successfully. Otherwise, the indicator will not
flash.
5-2. Binding
To make Z713 work with the humidity/ temperature/ ultraviolet measurement device, users need to bind the
two devices:
Step1. Press and hold the Binding Key for 3 seconds to broadcast the binding request. The indicator will
flash once.
Step2. Enable the binding feature of the humidity/ temperature/ ultraviolet measurement device.
Step3. The indicator flashes 5 times after the binding is completed; otherwise, it flashes 10 times.
5-3. Sleeping Mode
Z713 is designed to go into sleeping mode for power-saving in some situations:
A. While the device is in the network → the sleeping period is 5 minutes; it will wake up every 5
minutes to keep online.
B. When it doesn’t find a network to join → Z713 will go to sleeping mode. It will wake up every 15
minutes to search a network to join.
C. Once Z713 was joined to a network and by any chance the network is no longer existed or the device
is out of the network → Z713 will wake up every 15 minutes to find the network it joined before.
It never keeps in sleeping mode and continues to find out a network every 15 minutes. This condition would
consume up to 30 times power spending compared to normal-operating status. To prevent this unwanted power
consumption, we recommend that users remove the batteries to power off the device.

7
5-4. Wake up Z713
When users would like to setup or acquire data from the device which is in sleeping mode, we have to wake
up the device as the following steps:
Step1. Press the Binding Key.
Step2. The indicator flashes 5 times when Z713 is online.
Step3. Z713 will broadcast the device data such as IP address or IEEE address to the ZigBee network.
5-5. Battery
After joining the network, Z713 checks the battery level every 60 minutes. When the operating voltage is
lower than 2.4V, the indicator will flash once. Z713 will send a low-power report to the ZigBee network.
5-6. Restore to Factory Setting
To restore it to factory setting, please follow the steps:
Step1. Remove the battery to power off Z713.
Step2. Press and hold the Binding Key, and then install the batteries to power on Z713.
Step3. Release the button. The indicator will show fast flashes, and the restore is completed.

8
6. Home Automation Clusters for Z713
A cluster is a set of related attributes and commands which are grouped together to provide a specific function. A
simple example of a cluster would be the On/Off cluster which defines how an on/off switch behaves. This table
lists the clusters which are supported by Z713.
Cluster ID for Z713
Server side Client side
EP 0x01 (Device ID: Temperature Sensor (0x0302) )
Basic(0x0000) None
Power Configuration(0x0001)
Identify(0x0003)
Commissioning(0x0015)
Hunidity Measurement(0x0405)
Temperature Measurement(0x0402)
ZCL_NETVOX_SPECIFIC_MIX_CLUSTE
R_ID(0xFE60)
This lists the attributes of the basic information.
Identifier Name Type Range Access Default Mandatory
/ Optional
0x0000 ZCLVersion Unsigned
8-bit integer
0x00 –
0xff
Read only 0x02 M
0x0001 ApplicationVersion Unsigned
8-bit integer
0x00 –
0xff
Read only O
0x0002 StackVersion Unsigned
8-bit integer
0x00 –
0xff
Read only 0x2A O
0x0003 HWVersion Unsigned
8-bit integer
0x00 –
0xff
Read only 0x47 O
0x0004 ManufacturerName Character
string
0 – 32
bytes
Read only netvox O
0x0005 ModelIdentifier Character
string
0 – 32
bytes
Read only Z711E0ED O
0x0006 DateCode Character
string
0 – 16
bytes
Read only 20130730 O

9
0x0007 PowerSource 8-bit
Enumeration
0x00 –
0xff
Read only 0x03 M
0x0010 LocationDescription Character
string
0 – 16
bytes
Read/write O
0x0011 PhysicalEnvironment 8-bit
Enumeration
0x00 –
0xff
Read/write 0x00 O
0x0012 DeviceEnabled Boolean 0x00 –
0x01
Read/write 0x01 M

10
7. Important Maintenance Instructions
In cases of accidental liquid spills to a device, please leave the device dry properly before storing or using.
Do not use or store the device in dusty or dirty areas.
Do not use or store the device in extremely hot temperatures. High temperatures may damage the device or
battery.
Do not use or store the device in extremely cold temperatures. When the device warms to its normal
temperature, moisture can form inside the device and damage the device or battery.
Do not drop, knock, or shake the device. Rough handling would break it.
Do not use strong chemicals or washing to clean the device.
Do not paint the device. Paint would cause improper operation.
Handle your device, battery, and accessories with care. The suggestions above help you keep your device
operational. For damaged device, please contact the authorized service center in your area.