Netvue NI-3250 User manual

Sentry Camera Quick Guide
NI-3250

FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that
this device does not cause harmful interference (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used by the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure conditions without restriction.
The antennas used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located for operating in conjunction with any
other antenna or transmitter.
FCC ID 2AO8RNI-3250
CE RED
This product can be used across EU member states.
Warning

Catalogue
1. What’s In The Box
2. Camera Structure
3. Insert Micro SD Card
4. Read Before Installing
5. Set Up With Netvue App
6. Sentry Camera Installation
7. Status Light
8. Netvue Protect Plan
P. 1
P. 2
P. 3
P. 4
P. 5
P. 6-12
P. 13
P. 14

Quick Guide
X 4
Anchors
Sentry Camera
Power Adapter
Weatherproof Tube
What’s In The Box
X 4
Mounting Screws
Sentry Camera Quick Guide
Drilling Template
UP
1

Camera Structure
Infrared LEDs
Light Sensor
Lens
Wi-Fi
Configuration
Button
Ethernet Cable Port
Power Port
Status Light
Microphone
Micro SD Card Slot
Speaker
Antenna
TF
2

Micro SD Card Slot
1
2
Sentry Camera comes with a built-in card slot which supports up to 128GB
Micro SD card. Once you insert the storage card, the camera will automati-
cally start to record and store videos in the storage card. You can view those
videos on the ‘Replay’ page by clicking the ‘Replay’ button in the ‘Homepage’.
Step 1: Make sure your Sentry Camera is power off. Loosen the screws and then take
off the cover.
Step 2: Insert Micro SD card. Make sure you insert it in the correct direction. The
Front of the card should face up.
Step 3: Put the cover back and tighten the screws.
Insert Micro SD Card
RESET TF
3

1. Keep the Sentry Camera and all accessories out of reach of children and pets.
2. The Sentry Camera comes with a power adapter. If you prefer other
power adapter, please make sure that it allows a DC12V (≥1000mA)
power supply voltage.
3. The product can only be used at normal temperature and humidity:
Working temperature: -10°C - 50°C (14°F-122°F)
Working relative humidity: 0-95%.
4. Please do not expose the camera lens to direct sunlight.
5. Please do not install the camera where is likely struck by lightning.
4
Read Before Installing
Note:
1. Netvue Sentry Camera only works with 2.4GHz Wi-Fi.
2. Strong lights may interfere with the ability to scan the QR code.
3. Avoid placing the device behind furniture or near microwaves.
Try to keep it within range of your Wi-Fi signal.

Set Up with Netvue App
Download the Netvue App from App Store or Google
Play. Follow the in-app instruction to complete the entire
set up process.
5

Check the following things before you start to drill holes on your wall:
1. Sentry Camera has been successfully added to your Netvue
App and is able to stream video.
2. Have planned the cable route. Measured the length of the
power cable and Ethernet cable (if you plan to use Ethernet
connection) you will need.
Sentry Camera Installation
Step 1:
Find a good installation spot.
We recommend installing the Sentry camera just 7-10 feet (2-3
meters) above the ground for a better two-way audio experience.
There is a power outlet nearby.
Test whether Sentry camera can stream video smoothly at the spot.
Make sure the camera’s sight is not blocked.
6

7
7-10 feet (2-3 meters)
11'
10'
9'
8'
7'
6'
5'
4'
3'
2'
1'

Step 2:
If you are going to install camera on wood, just skip this step.
If you are going to install camera on concrete or brick:
Before you start to drill, make sure you know the locations of wall-in
pipes and electrical wires. (If you are not comfortable with drilling holes,
please consult with a licensed electrician.)
Use the provided drilling template to mark the position of holes on your
wall. Use drill bit (15/64", 6mm) to drill four holes, and then install
anchors to hold screws.
1
2
8

Step 3:
Loosen the security screw and take off the backplate, then install it on
the wall by provided mounting screws.
1
2
9

3
10

1
2
Step 4:
Hang Sentry Camera on the backplate, then tighten the security screw.
11

1
Step 5 (Wired Connection):
Read this step if you are using wired connection, otherwise skip this step.
Aweatherproof tube is needed for Ethernet cable to avoid leaking water
into Ethernet cable port. Insert the cable into the weatherproof tube, and
then connect it to the Ethernet cable port of Sentry Camera. Make sure the
cable works before installing.
Things you need:
Ethernet cable
3
2
Ethernet cable portEthernet cableweatherproof tube
12

DescriptionStatus Light
Solid Green
Rapidly Flashing Green
None
Online
Wi-Fi Configuration Mode
Offline
Netvue Sentry Camera uses status light to indicate the device status.
Status Light
13

Netvue Protect Plan
Visit my.netvue.com to learn more.
Netvue Protect Plan provides optional advanced features for those with
higher security needs, and each plan supports multiple devices.
Connuous Video Recording: It allows for non-stop recording of all the action,
and captures everything in the background, you can rewind to catch anything
you missed.
Event Video Recording: It automatically records a video clip, not just several
still pictures, and push it to your phone instantly, keeping you always stay in
the know anywhere, anytime.
Human Detecon: It uses machine learning to accurately identify people
within your Netvue video, sending you specific human alerts when a human is
detected, while still sending regular motion alerts for non-human activity.
14


Manufacturer's Name: NetvueTechnologiesCo.,Ltd.
Address:RoomA501‐502,AcademyofAerospaceTechnology,10KejinanRoad,
NanshanDistrict,Shenzhen,China,518057
Product Name: SentryCamera
Trade Mark: Netvue
Model number: NI‐3250,NI‐3251,NI‐3252,NI‐3253,NI‐3254,NI‐3255,
NI‐3256,NI‐3257,NI‐3258,NI‐3259
Operating Temperature: -10° C to 50° C
This device is in compliance with the essential requirements and other relevant provisions of Directive
2014/53/EU. All essential radio test suites have been carried out.
The device complies with RF specifications when the device used at 20cm from your
body.
. Adapter shall be installed near the equipment and shall be easily accessible.
. The plug considered as disconnect device of adapter.
Model: DS012A1200100HU
Input: Input: 100-240V~, 50/60Hz,300mA
Output: DC 12V/1A
Care for the environment! Must not be discarded with household waste!
RF Secification:
Function Operation Frequency
Max RF output
power: Limit
2.4G WIFI
802.11b/g/n
(HT20,HT40)
802.11b/g/n(20MHz): 2412~2472MHz;
802.11n(40MHz):2422~2462MHz 14.10dBm 20 dBm.
This product can be used across EU member states.


DECLARATION OF CONFORMITY

I hereby declare that the product

Product name: SentryCamera
Model name: NI-3250,
Series model : NI-3251,NI-3252,NI-3253,NI-3254,NI-3255,
NI-3256,NI-3257,NI-3258,NI-3259
HW: J14IP
SW: 5.10.7(75843)

(Name of product, type or model, batch or serial number)

satisfies all the technical regulations applicable to the product within the scope of Council Directives
2014/53/EU, 2014/35/EU and 2014/30/EU: and declare that the same application has not been
lodged with any other notified body.
ETSI EN 300 328 V2.2.2 (2019-07)

ETSI EN 301 489-1 V2.2.3 (2019-11)
Draft ETSI EN 301 489-17 V3.2.2 (2019-12)
EN 55032:2015
EN 55035:2017
EN 61000-3-2:2014
EN 61000-3-3:2013

EN 62311: 2008
EN 60950-1:2006 + A11:2009 + A1:2010+A12:2011+A2:2013

(Title(s) of regulations, standards, etc.)
All essential radio test suites have been carried out.

Adapter information：

Adapter 1:
Model: DS012A1200100HU
Input: 100-240V~50/60Hz 300mA
Output:12.0V 1000mA
Adapter 2:
Model: DS012A1200100HE
Input: 100-240V~50/60Hz 300mA
Output:12.0V 1000mA
Adapter 3:
Model: DS012A1200100HK
Input: 100-240V~50/60Hz 300mA
Output:12.0V 1000mA
Adapter 4:
Model: XS-1201000HAU
Input: 100-240V~47/63Hz 300mA
Output:12.0V 1000mA

MANUFACTURER or AUTHORISED REPRESENTATIVE:

−Address:
Netvue Technologies Co.,Ltd.

Room A501-502,Academy of Aerospace Technology,10 Kejinan Road,Nanshan
District,Shenzhen,China,518057

This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised
representative.


Point of contact:

Netvue Technologies Co.,Ltd.
Telephone : [phone]
Tax number: [phone]


(Name, telephone and fax number)


RoomA501‐502,AcademyofAerospaceTechnology,10KejinanRoad,Nanshan
District,Shenzhen,China,518057