Networker TS790 User manual

TS790 / TS900
Intruder Alarm Control Panels
User Manual
_
~
Engineers menu 2
Select option :-
_
~
OPEN
_
~
Engineers menu 2
Select option :-
_
~
_
~
OPEN
1A
D
C
B
2 3
7
6
5
4
8 9
0
ENT ESC
_
~
SYSTEM OPEN
17:30 Wed 11 NOV
SILENTZONEOMIT
CHIMENEWCODE 24Hr OMIT
WALKTESTBELLTESTPart Set
PartSet
Part Set
RESET
1
A
B
C
D
2 3
456
7
ENT ESC
8
0
9
Sett ing th e System
Ent er y our pa s s code XXXX
th en lea ve th e p ro tec t ed a re a.
Unsetting the Syste m
Go dir e ctl y to t h e k e yp ad and
en ter you r p as sco d e XXXX.
Resetting
Ent er y our pa s s code XXXX fo ll ow ed
by EN T the n 3. Te leph o n e you r a l arm
com pan y and foll ow th ei r inst ruc t io ns.
!
See U ser Ma nual
FULLS ET

Quick Reference Guide
Full Set Enter your passcode ????
Part Set Enter your passcode ????
Press A, B or C as required Aor Bor C
Unset Enter your passcode ????
Silent Full Set Enter your passcode ????
Press 8 8
Silent Part Set Enter your passcode ????
Press A, B or C as required Aor Bor C
Press 8 8
Bell Test Enter your passcode ????
Press [ENT] within 5 secs. [
Press 1 (sounders on) 1
Press [ESC] when finished ]
Walk Test Enter your passcode ????
Press [ENT] within 5 secs. [
Press 2 2
Conduct Walk Test Conduct Walk Test
Press [ESC] when finished ]
Remote Reset Enter your passcode ????
Press [ENT] within 5 secs. [
Press 3 3
Contact your central station and quote 4 digit number
Enter reply number ????
Press [ENT] [
Press [ESC] when finished ]
Change Passcode Enter your passcode ????
Press [ENT] within 5 secs. [
Press 4 4
Enter new passcode ????
Press [ENT] to accept [
Press [ESC] when finished ]
Overview

CONTENTS
Quick Reference Guide
Overview Introduction............................................1
RemoteKeypads.......................................2
ArmingStation..........................................2
LEDKeypad ...........................................2
StarburstKeypad........................................3
LCDKeypad...........................................3
Operating The System
Introduction............................................4
UserMenus............................................4
EngineeronSiteMessage.................................4
FullSettingTheSystem ...................................5
UnsettingTheSystem.....................................6
Part-Setting Using The Part-Set Buttons . . . . . . . . . . . . . . . . . . . . . . . . 7
Part-Setting With Part Set Passcodes . . . . . . . . . . . . . . . . . . . . . . . . . 8
SilentSetting..........................................10
UnsettingAfterAnAlarm.................................11
ResettingAfterAnAlarm.................................11
User Reset...........................................11
Engineer Reset ......................................12
Remote Reset .......................................12
Setting individual Wards with Standard User Passcodes. . . . . . . . . . 13
Unsetting individual Wards with Standard User Passcodes. . . . . . . . 14
Setting & Unsetting Wards with the Code Set Group Passcodes . . . 16
User Menu 1
Introduction...........................................17
BellTest-[1.1].........................................18
WalkTest-[1.2]........................................18
RemoteReset-[1.3]....................................19
ChangePasscode-[1.4]................................19
EnableChime-[1.5]....................................19
Omit24HourGroup-[1.6]...............................20
OmittingCircuits-[1.7]..................................20
SilentSet-[1.8]........................................22
ViewActivityCount-[1.9]................................22
Full Set and Part-set - [1.0,A,B,C]. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
User Menu 2
Introduction...........................................23
ViewCircuits-[2.1].....................................24
SetClock-[2.2]........................................24

SetDate-[2.3]........................................25
SetupUsers-[2.4]......................................25
AlterChimeCircuits-[2.5]................................28
Alter24HrGroup-[2.6]..................................28
PrintSystemLog-[2.7]..................................29
ConfigureWards-[2.8]..................................30
Viewing the System Log with an LCD Remote Keypad - [2.9] . . . . . 31
Viewing The Log With an LED or Starburst Remote Keypad - [2.9] . . 31
RemoteCallBack-[2.0].................................33
Initiate Remote Service Call - [2.A] . . . . . . . . . . . . . . . . . . . . . . . . . 34
User Menu 3
Introduction...........................................35
TimeSwitchA,B&C-[3.1]...............................36
SelectingTimeSwitches..........................36
SettingTheOnTimes............................36
SettingTheOffTimes............................37
Setting The Days Of Operation . . . . . . . . . . . . . . . . . . . . 37
SettingTheDay................................38
Manually Switching The Output . . . . . . . . . . . . . . . . . . . . 38
PartSetGroups-[3.2]...................................39
CodeSetGroups-[3.3].................................40
User Names (TS900 Remote Keypads Only) - [3.4] . . . . . . . . . . . . . 41
Edit Text For Part Set Groups (TS900 Remote Keypads Only) - [3.5] . 41
Edit Circuit Text (TS900 Remote Keypad Only) - [3.6]. . . . . . . . . . . . 42
ViewInactiveCircuits-[3.0] ..............................43
TextKeypad..........................................44
Fault Finding
DisplayMessages......................................45
DisplayMessages(Cont.)................................46
GlossaryofTerms......................................47

Introduction
The TS790 and TS900 are advanced security alarm control systems using state of the art
electronics to provide comprehensive but flexible protection for both domestic and
commercial premises. The system comprises of a number of components linked to a central
control unit which is concealed from view but accessible for maintenance. The TS790 can
monitor from 10 to 16 detection circuits whereas the TS900 can monitor a maximum of 56.
Both systems can be operated from up to four remote keypads which may be one of four types.
Detection devices such as door contacts or movement sensors are allocated to detection
circuits which are identified on the remote keypad displays. All detection circuits may then be
allocated to the whole system or grouped into “Wards” (areas) so that access to certain areas
can be controlled independently.
A modem can also be connected to the alarm system via the telephone line to allow remote
interrogation,programmingandresettingofalarms.Thisfeature isknownas“Downloading”and
is normally performed by the installation company or central station.
Each alarm installation is specific to the site and its occupier and may differ from other
TS790/TS900 installations. This manual describes in detail all the functions and procedures
available to the user, however, not all these may be relevant to the way your system is set up. To
avoid unnecessary operating errors please discuss the details of the alarm system with your
installation company before attempting to use it. Also ensure that installation company
complete the system record sheets at the back of this manual and fill in the details required
within the section called “Operating The System”.
1
TS790/TS900 User Manual Overview

Remote Keypads
Your alarm system can be operated from one or more remote keypads, which will have been
strategically located within the protected premises. The remote keypads may be one of four
types.
Arming Station
The remote arming station can only be used to full set, part set and unset your alarm system.
Green Power Indicator - Flashes if no
mains power is present. Steady when
mains power is present.
Red Function Indicator - Can be
programmed by the alarm company,
to indicate a fault, set or part-set etc.
Keyboard - Used for operating your
alarm system.
Cover - Fold-down cover with quick
guide operating instructions.
LED Keypad
The LED remote keypad can be used to full set, part set and unset the alarm system. It also can
be used for limited programming functions.
LED Display - Used to show the system
time along with other system
messages.
Green Power Indicator - Flashes if no
mains power is present. Steady when
mains power is present.
Red Function Indicator - Can be
programmed by the alarm company,
to indicate a fault, set or part-set etc.
Keyboard - Used for operating your
alarm system.
Cover - Fold-down cover with quick
guide operating instructions.
2
Overview TS790/TS900 User Manual
1A
D
C
B
23
7
6
5
4
8 9
0
ENT ESC
_
~
SILENTZONE OMIT
CH IMENE W CODE 24 Hr OMIT
WALK TESTB ELL TES TPar t Set
Part Set
Part Set
RE SET
1
A
B
C
D
2 3
456
7
ENT ESC
8
0
9
Sett ing the Syst em
Ent er your pa ss c ode XXXX
th en le a ve th e p ro tec t ed a re a.
Unse tting the System
Go di re ct ly to t he k e yp ad and
en ter you r p a ssc od e XXXX .
Rese tting
Ent er your pa ss c ode XXXX f ol low e d
by EN T the n 3. Te l eph on e y ou r a l arm
co m pan y and fol low th ei r ins tr uct io ns.
!
See User Manual
FULL S ET




1A
D
C
B
23
7
6
5
4
8 9
0
ENT ESC
_
~
OPEN
SILENTZONE OM IT
CH IMENE W CODE 24 Hr OMIT
WALK TESTB ELL TES TPar t Set
Part Set
Part Set
RE SET
1
A
B
C
D
2 3
456
7
ENT ESC
8
0
9
Sett ing the Syst em
Ent er your pa ss c ode XXXX
th en le a ve th e p ro tec t ed a re a.
Unse tting the System
Go di re ct ly to t he k e yp ad and
en ter you r p a ssc od e XXXX .
Rese tting
Ent er your pa ss c ode XXXX f ol low e d
by EN T the n 3. Te l eph on e y ou r a l arm
co m pan y and fol low th ei r ins tr uct io ns.
!
See User Manual
FULL S ET





Starburst Keypad
The Starburst remote keypad can be used to full set, part set and unset the alarm system. It also
can be used for limited programming functions.
Starburst Display - Used to show the
system time along with other system
messages.
Green Power Indicator - Flashes if no
mains power is present. Steady when
mains power is present.
Red Function Indicator - Can be
programmed by the alarm company,
to indicate a fault, set or part-set etc.
Keyboard - Used for operating your
alarm system.
Cover - Fold-down cover with quick
guide operating instructions.
LCD Keypad
The LCD remote keypad is a full function keypad and can be used to program, test, set and
unset the alarm system.
LCD Display - Used to show the system
time along with other system
messages.
Green Power Indicator - Flashes if no
mains power is present. Steady when
mains power is present.
Red Function Indicator - Can be
programmed by the alarm company,
to indicate a fault, set or part-set etc.
Keyboard - Used for operating your
alarm system.
Cover - Fold-down cover with quick
guide operating instructions.
3
TS790/TS900 User Manual Overview
1A
D
C
B
2 3
7
6
5
4
8 9
0
ENT ESC
_
~
SYSTEM OPEN
17:30 Mon 01 JAN
SILENTZONE OMIT
CHIMENEW CODE 24Hr OMIT
WALK TESTBELL TES TPart Set
Part Set
Part Set
RE SET
1
A
B
C
D
2 3
4 5 6
7
ENT ESC
8
0
9
Setting the System
Ent e r y our pa s sc ode XXX X
th en l ea ve th e pr o tec t ed a re a.
Unsetting the System
Go d ir e ct ly to t h e k e yp ad and
en ter you r p ass cod e X XX X .
Resetting
Ent e r y our pa s sc ode XXX X f ol low ed
by EN T the n 3. Tel eph on e y ou r a l arm
co m pan y an d fo llo w th ei r i nstr uc t io ns .
!
See Use r Manual
FULL SET




1A
D
C
B
23
7
6
5
4
8 9
0
ENT ESC
_
~
OPEN
SILENTZONE OM IT
CH IMENE W CODE 24 Hr OMIT
WALK TESTB ELL TES TPar t Set
Part Set
Part Set
RE SET
1
A
B
C
D
2 3
456
7
ENT ESC
8
0
9
Sett ing the Syst em
Ent er your pa ss c ode XXXX
th en le a ve th e p ro tec t ed a re a.
Unse tting the System
Go di re ct ly to t he k e yp ad and
en ter you r p a ssc od e XXXX .
Rese tting
Ent er your pa ss c ode XXXX f ol low e d
by EN T the n 3. Te l eph on e y ou r a l arm
co m pan y and fol low th ei r ins tr uct io ns.
!
See User Manual
FULL S ET





Operating The System
Introduction
Initial access to the system is gained by entering a 4 digit passcode. Every time you wish to use
the system your passcode must be entered correctly. If a passcode is repeatedly entered
incorrectly a code tamper alarm will be generated.
Up to 31 separate user passcodes are available for operating the system. The master user (user
01) is the person responsible for allocating other users to the system.
Each user (02-31) may be defined for different authorisation levels. See page 25 for full details,
the table below shows the code levels and their menu access:
Code level User Menu 1 User Menu 2 User Menu 3
Master 44*4*
Standard 4
Holiday 4
Set Only 4
Reset Only Options 1-9 only
PA Code 4
Access Used for access control
Full Set Group Only allows setting and unsetting of selected wards
Code Set Group A
Code Set Group B
Code Set Group C
*Iftheinstallationcompanyhasprogrammedthemasteruserforlimitedaccess,heorshewillNOThaveaccessto
“User menu 2" options 6 and 8, and all options in ”User menu 3".
User Menus
In general when ever a user passcode is entered the system will enter into a 5 second function
mode,ifthe[buttonispressed duringthistime “Usermenu1"isselected,asareminder,abrief
descriptionofeach menuoption within”User menu1“isprinted underneath eachbuttononthe
the remote keypads, e.g., button 1 selects the ”Bell Test" option. If the [button is not pressed
within 5 seconds the system will attempt to full set.
When any of the menu options are selected the user may abandon the function by pressing the
]button. If the ]button is repeatedly pressed whilst one of the user menus is selected, the
alarm system will return to the normal “OPEN” condition.
Engineer on Site Message
When the installation engineer attends the site for routine maintenance etc. the remote
keypads may show “Engineer on site” (ENG ON SITE), whilst this message is displayed the
alarm system remains fully operational. However, before the engineer leaves the site he should
ask one of the users to enter their passcode followed by ], this will clear the "Engineer on site”
message and return the system to the normal “OPEN” condition.
4
Operating The System TS790/TS900 User Manual

Full Setting The System
The full setting procedure may be initiated from any remote keypad (if more than one is fitted).
Before attempting to full set the alarm system ensure that all movement detectors are
unobstructed and all doors, and windows are secure.
Theinstallationcompanywillhaveset-upyouralarm systemtofullsetbyoneofthefollowing:
Timed Exit -After entering your passcode the alarm system will be full set after the
pre-programmed exit timer has expired. The display at step (2) will
count down the remaining exit time.
Final Exit -After entering your passcode the alarm system will be full set after the
Final Exit door is opened and closed. The display at step (2) will show a
count of 9999.
Exit Terminator -After entering your passcode the alarm system will be full set after the
Final Exit door is opened and closed, and after pressing the Exit
Terminator button (a push button normally mounted outside of the
premises). The display at step (2) will show a count of 9999.
Instant -After entering your passcode the alarm system will be full set after 5
seconds.
+If an attempt is made to full set the system whilst any circuits are active (such as a door
being open) the display at step (2) will indicate the circuit(s) that are in fault and internal
sounder generates an interrupted tone. The fault must be cleared before the setting
procedure can be completed. If the system is set by "Timed Exit" or "Instant", and the fault
is still present at the end of the exit time an internal alarm will be generated. If fitted, the
external strobe light will flash indicating that the system has “Failed to set”. To prevent this
alarm simply re-enter your passcode before the exit timer expires.
»To full set the system proceed as follows:
1. Enter your passcode ????. The
display will show:
2. After 5 seconds the exit sounder will start
and the display will show:
3. Leave via the prescribed exit route.
4. The system is set when the exit time has
expired, on activation of the Final Exit circuit
or pressing the Exit Terminator button, as
appropriate. The exit sounder will stop and
the display will show:
5. After 5 seconds the “SYSTEM SET”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
Setting Mode: Timed oFinal Exit oExit Terminator oInstant o
Exit Time: ________________________
5
TS790 & TS900 User Manual Operating The System
Press ENT to
Select Functions
LCD
FUNCTION
Starburst
Func.
LED
Please Exit Now.
Time left > 9999 9999 9999
SYSTEM SET
05:30 Sun 28 APR SET SET
ABC SECURITY
05:30 Sun 28 APR 05:30 05.30

Unsetting The System
The unsetting of the alarm system can be performed from any remote keypad.
»To unset your alarm system, proceed as follows:
1. Enter the premises via the prescribed
entry route and proceed directly to the
remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time, e.g.,
2. Enteryourpasscode ????before
theentry timerexpires.The internalsounders
will stop and the display will show:
3. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
+If the entry time is exceeded an alarm is generated from the internal sounders and the
“Second Entry” timer is started. If at the end of the “Second Entry” timer the alarm system
hasnotbeenunsetafullalarm conditionwilloccur.Iftheinstallationcompanyhassetthe
“Second Entry” timer to zero the full alarm will occur when the first entry timer expires.
+If during the entry procedure the user strays from the prescribed entry route and activates
a detection circuit a full alarm will occur (internal sounders and external sounders). If the
alarm system is fitted with a remote signalling device such as a digicom this will also be
triggered and police action will be taken. However, the alarm system may be
programmed with an “Entry Abort” feature which will allow a further preset time delay to
occur if a detection circuit is accidentally triggered during the entry procedure. This will
delay the triggering of the remote signalling device and allow the user time to unset the
system. The delay is normally set to 90 seconds by your installation company.
Full Set Entry Time: __________________
Second Entry Time: __________________
Part-set Entry Time: __________________
Entry Abort Delay: __________________
6
Operating The System TS790 & TS900 User Manual
Enter Your Code
Time left > 0025
LCD
0025
Starburst
0025
LED
SYSTEM OPEN
08:30 Sun 28 APR OPEN OPEN
ABC SECURITY
08:30 Sun 28 APR 08:30 08.30

Part-Setting Using The Part-Set Buttons
The TS790 & TS900 can have up to three predefined part-set configurations. Each configuration
allows the alarm system to set with one or more wards isolated. Each configuration is then
assigned to a part-set button A, B or C, normally this will be done by the installation company at
the time of commissioning. However the master user may also configure the part-set buttons,
providing the installation company has programmed the alarm system to allow this facility (see
“Part Set Groups on page 39).
»To part-set the alarm system, proceed as follows:
1. Enter your passcode ????. The
display will show:
2. Within 5 seconds press the required
part-set button A,Bor C, e.g., press “A”
for part-set A. The display will show:
3. The exit sounder will start. If necessary
leave the area via the prescribed exit route.
Thedisplaywillshow theremaining exittime,
e.g.,
4. The system will be part-set when the exit
time has expired, on activation of the Final
Exit circuit or by pressing the Exit Terminator
button, as appropriate. When the system is
part-set the display will show the wards that
are set and the time, e.g.,
+The text shown on the LCD remote keypads at step (2) may be programmed by the
master user (see “Edit Text for Part-Set Groups” on page 41). If the text is not programmed
the display will read the default “Part Set group A” for the above example.
+If the alarm system has LED remote keypads fitted, the installation company may have
programmed the system so that the alternating displays shown at step (4) only show the
time.
Part-Set A: _________________________________________________________
Setting Mode: Timed oFinal Exit oExit Terminator oInstant o
Part-Set B: _________________________________________________________
Setting Mode: Timed oFinal Exit oExit Terminator oInstant o
Part-Set C: _________________________________________________________
Setting Mode: Timed oFinal Exit oExit Terminator oInstant o
7
TS790 & TS900 User Manual Operating The System
Press ENT to
Select Function
LCD
FUNCTION
Starburst
Func.
LED
Setting the
Office Area Only P. SET A PS.A
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ A ]
05:30 Sun 28 APR PART SET P.SET
AA
05.30 05.30

Part-Setting With Part Set Passcodes
Passcode types “Code Set Group A”, “Code Set Group B”, “Code Set Group C”, and the “Full Set
Group” enable the user to set and unset only the wards assigned to their “Code Set Group”. The
“Code Set Groups” are configured by the master user or installation company (see “Code Set
Groups” on page 40).
The following example shows how to set and unset wards A and B using the passcode type
“Code Set Group A”. The example first assumes that the alarm system is initially unset.
»To set your area(s) using a “Code Set Group” passcode, proceed as follows:
1. Enter your “Code Set Group” passcode
????. The exit sounder will start. If
necessaryleavetheareaviatheprescribed
exit route. The display will show the
remaining exit time, e.g.,
2. The system is part-set when the exit time
has expired, on activation of the Final Exit
circuit or by pressing the Exit Terminator
button, as appropriate. When the system
has part-set the display will show the wards
that are set and the time e.g.,
»To unset your area(s), proceed as follows:
1. Enter the area or premises via the
prescribed entryroute and proceeddirectly
tothe remotekeypad.The internalsounders
generate an interrupted tone. The display
will show the remaining entry time, e.g.,
2. Enter your “Code Set Group” passcode
????within the entry time. The
internal sounders will stop and the display
will show:
3. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
The “Code Set Group” passcodes may be used when the system is fully set. When the passcode
is entered only those wards assigned to the “Code Set Group” will be unset.
The following example shows how to unset wards A and B using the passcode type “Code Set
Group A”. The example first assumes that the alarm system is initially full set.
8
Operating The System TS790 & TS900 User Manual
Wards set [ AB ]
05:30 Sun 28 APR PART SET P.SET
AB AB
05.30 05.30
Please Exit Now.
Time left > 0025
LCD
0025
Starburst
0025
LED
Enter Your Code
Time left > 0025
LCD
0025
Starburst
0025
LED
SYSTEM OPEN
08:30 Sun 28 APR OPEN OPEN
ABC SECURITY
08:30 Sun 28 APR 08:30 08.30

Part-Setting With Part Set Passcodes (Cont.)
»To unset your area(s), proceed as follows:
1. Enter the area or premises via the
prescribed entryroute and proceeddirectly
tothe remotekeypad.The internalsounders
generate an interrupted tone. The display
willshowhowmuchtimeyouhavelefte.g.,
2. Enter your “Code Set Group” passcode
????within the entry time. The
internal sounders will stop and the display
will show the wards that have remained set
and the time, e.g.,
The system may be returned to the full set condition by re-entering the “Code Set Group”
passcode and leaving the area or premises via the prescribed exit route. The system may also
be fully unset at any time by entering a valid passcode (Master, Standard or Holiday).
Code Set Group A: Sets/unsets wards S: oA: oB: oC: o
Code Set Group B: Sets/unsets wards S: oA: oB: oC: o
Code Set Group C: Sets/unsets wards S: oA: oB: oC: o
Full Set Group: Sets/unsets wards S: oA: oB: oC: o
9
TS790 & TS900 User Manual Operating The System
Wards set [S C]
09:30 Sun 28 APR PART SET P.SET
S C S C
09.30 09.30
Enter Your Code
Time left > 0025
LCD
0025
Starburst
0025
LED

Silent Setting
The alarm system may be full or part-set such that the internal sounders are switched off during
the exit procedure. However the system will give a short tone at the end of the exit procedure to
indicate that the system has successfully set.
»To full set the alarm system silently, proceed as follows:
1. Enter your passcode ????. The
display will show:
2. Within 5 seconds press 8. The display
will show:
3. Leave via the prescribed exit route.
4. The system is full set when the exit time
has expired, on activation of the Final Exit
circuit or by pressing the Exit Terminator
button, as appropriate.
»To part-set the alarm system silently, proceed as follows:
1. Enter your passcode ????. The
display will show:
2. Within 5 seconds press the required
part-set button A,Bor C, e.g., press “A”
for part-set A then press 8. The display will
show:
3. Leave the area or premises via the
prescribed exit route.
4. The system is part-set when the exit time
has expired, on activation of the Final Exit
circuit or by pressing the Exit Terminator
button, as appropriate.
10
Operating The System TS790 & TS900 User Manual
Press ENT to
Select Functions
LCD
FUNCTION
Starburst
Func.
LED
Please Exit Now.
Time left > 9999 9999 9999
Press ENT to
Select Function
LCD
FUNCTION
Starburst
Func.
LED
Setting the
Office Area Only P. SET A PS.A

Unsetting After An Alarm
If an alarm has occurred whilst the alarm system is full or part-set, the display will indicate the
detection circuit that was triggered when the system is unset. Once the cause of the alarm has
been established the system must be reset (see “Resetting after an alarm”).
1. Enter the premises or area via the
prescribed entryroute and proceeddirectly
tothe remotekeypad.The internalsounders
will generate an interrupted tone. The
display will show how much time you have
left, e.g.,
2. Enter your passcode ????within
theentry time.Theinternalsounders willstop
and the display will show the detection
circuit that caused the alarm, e.g.,
3. Refer to “Resetting after an Alarm”
+If “Circuit Text” has been programmed then the display on the LCD and Starburst remote
keypads will alternate between the “Circuit number” and the “Circuit Text” at step (2).
Resetting After An Alarm
The installation company will have programmed the system to be either “User Reset”,“Engineer
Reset” or “Remote Reset”, consult your installation company if you are not sure.
User Reset
From step (3) of “Unsetting After An Alarm” proceed follows:
1. Enter your passcode ????. The
display will show:
2. Within 5 seconds press ]. The display
will show:
3. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
Your alarm system is reset by: User: oEngineer: oRemote Reset: o
(Continued Over)
11
TS790 & TS900 User Manual Operating The System
ALARM 03
09:45.59 28/04 ALARM 03 CA.03
Enter Your Code
Time left > 0025
LCD
0025
Starburst
0025
LED
Office Detector
09:45.59 28/04 OFFICE
Press ENT to
Select Functions
LCD
FUNCTION
Starburst
Func.
LED
SYSTEM OPEN
08:30 Sun 28 APR OPEN OPEN
ABC Security
08:30 Sun 28 APR 08.30 08.30

Engineer Reset
From step (3) of “Unsetting After An Alarm” proceed as follows:
1. The display will cycle between the
detectioncircuitthatcaused thealarmand
the “CALL ENGINEER TO RESET SYSTEM”. The
system will also “beep” every minute to
indicate the system requires an engineer to
reset the system. To silence the “beeps”
simply enter your passcode ????.
2. Call the installation company to attend
and reset your system.
Tel No._____________________________
+The display shown at step 2 is programmable and may show something different.
Remote Reset
From step (3) of “Unsetting After An Alarm” proceed as follows:
1. Follow Step (1) of the “Engineer Reset”
procedure.
2. Enter your passcode ????. The
display will show:
3. Within 5 seconds press [. “User Menu 1"
is selected, the display will show:
4. Press 3to select the Remote Reset
option. The display will show a random four
digit “Seed Code” e.g.,
5. Write downthe “Seed Code”.Telephone
your central station and quote the “Seed
Code”. You will be asked to report the
circumstances of the alarm. If an engineer
is not required to attend site you will be
given a unique four digit “Remote Reset”
code.
6. Enter the four digit “Remote Reset” code
???? then press [. A muti-tone beep
willconfirmacceptanceand thedisplay will
return to “User Menu 1":
7. Press ]to return to the Unset condition,
the display will show:
8. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
12
Operating The System TS790 & TS900 User Manual
ALARM 03
09:45.55 28/04
LCD
ALARM 03
Starburst
CA.03
LED
Office Detector
09:45.55 28/04 OFFICE
CALL ENGINEER TO
RESET SYSTEM CALL CALL
ENGINEER ENG.
Press ENT to
Select Functions
LCD
FUNCTION
Starburst
Func.
LED
User menu 1
Select Option :- USER 1 - 1 -
Remote Reset
Quote > 6846 6846 6846
User menu 1
Select Option :- USER 1 - 1 -
SYSTEM OPEN
08:30 Sun 28 APR OPEN OPEN
ABC Security
08:30 Sun 28 APR 08.30 08.30
Remote Reset
Reply > ---- ---- ----
Tel No._____________________________

Setting individual Wards with Standard User Passcodes
The installation company can enable certain standard users to have access to the “Ward
Selection Menu”. This feature allows the user to select the wards that they require to set at the
time of setting the alarm system.
»The following example shows how to set wards B and C.
1. Enter your passcode ????. The
display will show:
2. Select the setting option as follows:
APart-set A
BPart-set B
CPart-set C
0Ward Selection Menu
NOTE: If an option is not selected after
5 seconds the system will attempt to
full set.
3. Press 0to select the “Ward Selection
Menu”. The display will show:
4. Select/deselectthewardsbypressing:
Afor “Ward A”
Bfor “Ward B”
Cfor “Ward C”
0for “Ward S”
e.g., to set wards B and C, deselect
wards S and A. The display will show:
5. When the display shows the required
wards, press [. The exit sounder will start, if
required leave via the prescribed exit route.
Thedisplaywillshowtheremainingexittime:
6. Whenexittonestopsthedisplaywillshow
the wards that are set and the e.g.,
+The “Ward Selection Menu” is displayed for a pre-programmed amount of time, which is
programmed by the installation company. If no wards are deselected at the end of the
pre-programmed time the alarm system will attempt to full set.
13
TS790 & TS900 User Manual Operating The System
Press ENT to
Select Functions
LCD
FUNCTION
Starburst
Func.
LED
Please Confirm
Set-:SABC SABC SABC
Please Confirm
Set-:**BC --BC --BC
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ BC]
05:30 Sun 28 APR PART SET P.SET
BC BC
05.30 05.30

Unsetting individual Wards with Standard User Passcodes
If the installation company has configured the alarm system as described on the previous page
the standard and master users will be given access to the “Ward Selection Menu” when
unsetting the alarm system.
»The following example shows how to unset wards A and B.
1. Enter the premises via the prescribed
entry route and proceed directly to the
remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time:
2. Enteryourpasscode ????before
theentrytimerexpires.Thedisplaywillshow:
3. Deselect the wards by pressing:
Afor “Ward A”
Bfor “Ward B”
Cfor “Ward C”
0for “Ward S”
e.g., to unset wards A and B, deselect
wards S and C. The display will show:
4. When the display shows the required
wards, press [. The entry sounder will stop
and the display will show the wards that are
set:
»To unset further wards (assuming wards S and C are set)
1. To unset another ward enter your
passcode ????. The display will
show:
2. Select the ward(s) you require to unset,
e.g., to unset ward C, deselect ward S. The
display will show:
3. When the display shows the required
ward(s) press [. The display will show the
wards that are set:
14
Operating The System TS790 & TS900 User Manual
Please Confirm
Unset -: S A B C SABC SABC
Please Confirm
Unset -: * A B * -AB- -AB-
Wards set [S C]
05:40 Sun 28 APR PART SET P.SET
S--C S--C
05.40 05.40
Please Confirm
Unset -: S * * C S--C S--C
Please Confirm
Unset -: * * * C ---C ---C
Wards set [S ]
05:50 Sun 28 APR PART SET P.SET
SS
05.50 05.50
Enter Your Code
Time left > 0025
LCD
0025
Starburst
0025
LED

»To Set further Wards (assuming ward A is set)
1. To set other wards enter your passcode
????. The display will show:
2. Deselect all wards so that the display
shows:
3. Press [and the display will show:
NOTE: Ward A is not displayed as it is
already set.
4. Select the ward(s) you require to set,
e.g., to set wards B and C, press 0 to
deselect ward S. The display will show:
5. When the display shows the required
wards, press [. The exit sounder will start, if
required leave via the prescribed exit route.
Thedisplaywillshowtheremainingexittime:
6. When the system has set the display will
show the wards that are set and the time:
+If the system is part-set, entry of a valid passcode is assumed to unset rather than set
further wards. To set further wards, it is necessary to unset nothing, the system will then
assume that you require to set further wards.
15
TS790 & TS900 User Manual Operating The System
Please Confirm
Unset -: * A * *
LCD
-A--
Starburst
-A--
LED
Please Confirm
Unset -: * * * * ---- ----
Please Confirm
Set-:S*BC S-BC S-BC
Please Confirm
Set-:**BC --BC --BC
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ ABC]
06:00 Sun 28 APR PART SET P.SET
ABC ABC
06.00 06.00

Setting & Unsetting Wards with the Code Set Group Passcodes
If the installation company has enabled the "Ward Selection Menu" for your alarm system, all
users defined as "Code Set Group" users will also have access to the "Ward Selection Menu".
Howeverthe userscanonlyselectordeselectthe wardsthathavebeenassigned to their“Code
SetGroup”,e.g.,if“CodeSetGroupA”isconfiguredtohaveaccesstowardsAandB,thenwhen
the “Ward Selection Menu” is displayed the user can only select or de-select wards A and B.
The following example uses "Code Set Group A" which is configured to have access to wards A
and B.
»Setting ward B with "Code Set Group A" passcode (system initially unset)
1. Enter your passcode ????, the
display will show:
2. Select the wards you require to set, e.g.,
to set ward B, deselect ward A:
3. When the display shows the required
ward(s) press [. The exit sounder will start, if
required leave via the prescribed exit route.
Thedisplaywillshowtheremainingexittime:
4. When the system has set the display will
show the wards that are set and the time:
»Unsetting ward B with "Code Set Group A" passcode (System initially full set)
1. Enter the premises via the prescribed
entry route and proceed directly to the
remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time:
2. Enteryourpasscode ????before
theentrytimerexpires.Thedisplaywillshow:
3. Select the wards you require to unset,
e.g., to unset ward B, deselect ward A:
4. When the display shows the required
wards, press [. The entry sounder will stop
and the display will show the wards that are
set:
16
Operating The System TS790 & TS900 User Manual
Please Confirm
Set-:*AB*
LCD
-AB-
Starburst
-AB-
LED
Please Confirm
Set-:**B* --B- --B-
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ B ]
06:00 Sun 28 APR PART SET P.SET
BB
06.00 06.00
Please Confirm
Unset -:* A B * -AB- -AB-
Please Confirm
Unset -: * * B * --B- --B-
Wards set [SA C]
06:30 Sun 28 APR PART SET P.SET
SA-C SA-C
06.30 06.30
Enter Your Code
Time left > 0025
LCD
0025
Starburst
0025
LED