Networker TS790 User manual

TS790 / TS900
10-56 Zone Intruder Alarm Control
Panels
User Manual
123
456
789
ENT 0ESC
ABC
OMIT AREA
POWER BUSY
123
456
789
ENT 0ESC
ABC
OMIT AREA
Engineers menu 1
Select Option :-
123
456
789
ENT 0ESC
ABC
OMIT AREA
POWER BUSY
123
456
789
ENT 0ESC
ABC
OMIT AREA
POWER FUNCTION
Intelligent Security & Fire Ltd

Quick Reference Guide
Full Set Enter your passcode XXXX
Part Set Enter your passcode XXXX
Press A, B or C as required Aor Bor C
Unset Enter your passcode XXXX
Silent Full Set Enter your passcode XXXX
Press 8 8
Silent Part Set Enter your passcode XXXX
Press A, B or C as required Aor Bor C
Press 8 8
Bell Test Enter your passcode XXXX
Press [ENT] within 5 secs. [
Press 1 (sounders on) 1
Press [ESC] when finished ]
Walk Test Enter your passcode XXXX
Press [ENT] within 5 secs. [
Press 2 2
Conduct Walk Test Conduct Walk Test
Press [ESC] when finished ]
Remote Reset Enter your passcode XXXX
Press [ENT] within 5 secs. [
Press 3 3
Contact your central station and quote 4 digit number
Enter reply number XXXX
Press [ENT] [
Change Passcode Enter your passcode XXXX
Press [ENT] within 5 secs. [
Press 4 4
Enter new passcode XXXX
Press [ENT]to accept [
Press [ESC] when finished ]
Intelligent Security & Fire Ltd

Contents
Overview
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
TS700 Remote Arming Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
TS700 LED Remote Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
TS790 Starburst Remote Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TS900 LCD Remote Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating The System
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
User Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Engineer on Site Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Full Setting The System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unsetting The System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Part-Setting Using The Part-Set Buttons . . . . . . . . . . . . . . . . . . . . . . . . 7
Part-Setting With Part Set Passcodes . . . . . . . . . . . . . . . . . . . . . . . . . 8
Silent Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unsetting After An Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Resetting After An Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
User Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Engineer Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting individual Wards with Standard User Passcodes. . . . . . . . . . 13
Unsetting individual Wards with Standard User Passcodes. . . . . . . . 14
Setting & Unsetting Wards with the Code Set Group Passcodes . . . 16
User Menu 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Bell Test - 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Walk Test - 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Remote Reset - 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Change Passcode - 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Enable Chime - 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Omit 24 Hour Group - 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Omitting Circuits - 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Silent Set - 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
View Activity Count - 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Full Set and Part-set - 0ABC . . . . . . . . . . . . . . . . . . . . . . . . . . 22
User Menu 2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
View Circuits - 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Set Clock - 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Set Date - 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setup Users - 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Alter Chime Circuits - 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Intelligent Security & Fire Ltd

Alter 24Hr Group - 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Print System Log -7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configure Wards - 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Viewing the System Log with an LCD Remote Keypad - 9. . . . . . . 31
Viewing The Log With an LED or Starburst Remote Keypad -9. . . . 31
Remote Call Back - 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Initiate Remote Service Call -A. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
User Menu 3
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Time Switch A, B & C - 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ABC. . . . . . . . . . . . . . . . . . . . . . 36
Setting The On Times - 123. . . . . . . . . . . . . . . . . . . . . 36
Setting The Off Times - 456. . . . . . . . . . . . . . . . . . . . . 37
Setting The Days Of Operation -789. . . . . . . . . . . . . . 37
Setting The Day -[. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Manually Switching The Output -0. . . . . . . . . . . . . . . . . 38
Part Set Groups - 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Code Set Groups - 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
User Names (TS900 Remote Keypads Only) -4. . . . . . . . . . . . . . . 41
Edit Text For Part Set Groups (TS900 Remote Keypads Only) -5. . . 41
Edit Circuit Text (TS900 Remote Keypad Only) -6. . . . . . . . . . . . . . 42
View Inactive Circuits - 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Text Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Fault Finding
Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Display Messages (Cont.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Intelligent Security & Fire Ltd

Overview
Introduction
The TS790 and TS900 are advanced security alarm control systems using state of the art
electronics to provide comprehensive but flexible protection for both domestic and
commercial premises. The system comprises of a number of components linked to a central
control unit which is concealed from view but accessible for maintenance. The TS790 can
monitor from 10 to 16 detection circuits where as the TS900 can monitor a maximum of 56.
Both systems can be operated from up to four remote keypads which may be one of four types.
Detection devices such as door contacts or movement sensors are allocated to detection
circuits which are identified on the remote keypad displays. All detection circuits may then be
allocated to the whole system or grouped into “Wards” (areas) so that access to certain areas
can be controlled independently.
A modem can also be connected to the alarm system via the telephone line to allow remote
interrogation, programming and resetting of alarms. This feature is known as “Downloading” and
is normally performed by the installation company or central station.
Each alarm installation is specific to the site and its occupier and may differ from other
TS790/TS900 installations. This manual describes in detail all the functions and procedures
available to the user, however, not all these may be relevant to the way your system is set up. To
avoid unnecessary operating errors please discuss the details of the alarm system with your
installation company before attempting to use it. Also make sure that your installation company
completes the system record sheets at the back of this manual and fills in the details required
within the section called “Operating The System”.
1
TS790/TS900 User Manual Overview
Intelligent Security & Fire Ltd

TS700 Remote Arming Station
The TS700 Remote Arming Station only allows setting and unsetting. The unit has two indicator
LED’s (Light Emitting Diodes), “POWER” and “FUNCTION”. The “FUNCTION” LED may be
programmed by the installation company to indicate faults or area set etc.
TS700 LED Remote Keypad
The TS700 Remote Keypad hasa4x7segment green Light Emitting Diode (LED) display and
back-lit tactile rubber keypad. With LED Remote Keypads text cannot be programmed but all
other system functions are available.
2
Overview TS790/TS900 User Manual
BC
Func.
A
ENT 0ESC
789
56
4
123
WALK TEST
BELL TEST RESET
NEW CODE CHIME 24hr OMIT
ZONE OMIT SILENT
FULL SET
OMIT AREA
POWER
Power LED
On = Mains On
Flashing = Mains Off
4 character LED Display
Part-set buttons Escape buttonEnter button
Figure 2 TS700 LED Remote Keypad
BCA
ENT 0ESC
789
56
4
123
WALK TEST
BELL TEST RESET
NEW CODE CHIME 24hr OMIT
ZONE OMIT SILENT
FULL SET
OMIT AREA
POWER FUNCTION
Power LED
On = Mains On
Flashing = Mains Off
Function LED
Part-set buttons Escape buttonEnter button
Figure 1 TS700 Remote Arming Station
Intelligent Security & Fire Ltd

TS790 Starburst Remote Keypad
The TS790 Starburst Remote Keypad has a back-lit 8 character Starburst display and back-lit
tactile rubber keypad. With Starburst Remote Keypads, text can be programmed but you are
limited to 8 characters.
TS900 LCD Remote Keypad
The TS900 Remote Keypad has a back-lit Liquid Crystal Display (LCD) and a back-lit tactile rubber
keypad. With LCD keypads the circuit text, user names and part-setting information may be
custom programmed to make the system easier to operate.
3
TS790/TS900 User Manual Overview
BCA
ENT 0ESC
789
56
4
123
WALK TEST
BELL TEST RESET
NEW CODE CHIME 24hr OMIT
ZONE OMIT SILENT
FULL SET
OMIT AREA
32 character LCD
Part-set buttons Escape buttonEnter button
Press ENT to
Select Functions
Figure 4 TS900 LCD Remote Keypad
BCA
ENT 0ESC
789
56
4
123
WALK TEST
BELL TEST RESET
NEW CODE CHIME 24hr OMIT
ZONE OMIT SILENT
FULL SET
OMIT AREA
POWER
Power LED
On = Mains On
Flashing = Mains Off
8 character Starburst LCD
Part-set buttons Escape buttonEnter button
FUNCTION
Figure 3 TS790 Starburst Remote Keypad
Intelligent Security & Fire Ltd

Operating The System
Introduction
Initial access to the system is gained by entering a 4 digit passcode. Every time you wish to use
the the system your passcode must be entered correctly. If a passcode is repeatedly entered
incorrectly a code tamper alarm will be generated.
Up to 31 separate user passcodes are available for operating the system. The master user (user
01) is the person responsible for allocating other users to the system.
Each user (02-31) may be defined for different authorisation levels. See page 25 for full details,
the table below shows the code levels and their menu access:
Code level User Menu 1 User Menu 2 User Menu 3
Master
44
* 4 *
Standard
4
Holiday
4
Set Only
4
Reset Only Options 1-9 only
PA Code
4
Access Used for access control
Full Set Group Only allows setting and unsetting of selected wards
Code Set Group A
Code Set Group B
Code Set Group C
* If the installation company has programmed the master user for limited access, he or she will NOT have access to
“User menu 2" options 6 and 8, or any options in ”User menu 3".
User Menus
In general when ever a user passcode is entered the system will enter into a 5 second function
mode, if the [button is pressed during this time “User menu 1" is selected, as a reminder, a brief
description of each menu option within ”User menu1“isprinted underneath each button on the
the remote keypads, e.g., button 1 selects the ”Bell Test" option. If the [button is not pressed
within 5 seconds the system will attempt to full set.
When any of the menu options are selected the user may abandon the function by pressing the
]button. If the ]button is repeatedly pressed whilst one of the user menus is selected, the
alarm system will return to the normal “OPEN” condition.
Engineer on Site Message
When the installation engineer attends the site for routine maintenance etc. the remote
keypads may show “Engineer on site” (ENG ON SITE), whilst this message is displayed the
alarm system remains fully operational. However, before the engineer leaves the site he should
ask one of the users to enter their passcode followed by ], this will clear the "Engineer on site”
message and return the system to the normal “OPEN” condition.
4
Operating The System TS790/TS900 User Manual
Intelligent Security & Fire Ltd

Full Setting The System
The full setting procedure may be initiated from any remote keypad (if more than one is fitted).
Before attempting to full set the alarm system ensure that all movement detectors are
unobstructed and all doors, and windows are secure.
The installation company will have set-up your alarm system to full set by one of the following:
-After entering your passcode the alarm system will be full set after the
pre-programmed exit timer has expired. The display at step (2) will
count down the remaining exit time.
-After entering your passcode the alarm system will be full set after the
Final Exit door is opened and closed. The display at step (2) will show a
count of 9999.
-After entering your passcode the alarm system will be full set after the
Final Exit door is opened and closed, and after pressing the Exit
Terminator button (a push button normally mounted outside of the
premises). The display at step (2) will show a count of 9999.
Instant -After entering your passcode the alarm system will be full set after 5
seconds.
+
If an attempt is made to full set the system whilst any circuits are active (such as a door
being open) the display at step (2) will indicate the circuit(s) that are in fault and internal
sounder generates an interrupted tone. The fault must be cleared before the setting
procedure can be completed. If the system is set by "Timed Exit" or "Instant", and the fault
is still present at the end of the exit time an internal alarm will be generated. If fitted, the
external strobe light will flash indicating that the system has “Failed to set”. To prevent this
alarm simply re-enter your passcode before the exit timer expires.
»To full set the system proceed as follows:
1. Enter your passcode XXXX. The
display will show:
2. After 5 seconds the exit sounder will start
and the display will show:
3. Leave via the prescribed exit route.
4. The system is set when the exit time has
expired, on activation of the Final Exit circuit
or pressing the Exit Terminator button, as
appropriate. The exit sounder will stop and
the display will show:
5. After 5 seconds the “SYSTEM SET”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
Setting Mode: Timed o Final Exit o Exit Terminator o Instant o
Exit Time: ________________________
5
TS790 & TS900 User Manual Operating The System
Press ENT to
Select Functions FUNCTION Func.
Please Exit Now.
Time left > 9999 9999 9999
SYSTEM SET
05:30 Sun 28 Apr SET SET
ABC SECURITY
05:30 Sun 28 Apr 05:30 05.30
Intelligent Security & Fire Ltd

Unsetting The System
You can unset the alarm system from any remote keypad.
»To unset your alarm system, proceed as follows:
1. Enter the premises via the prescribed
entry route and proceed directly to the
remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time, e.g.,
2. Enter your passcode XXXXbefore
the entry timer expires. The internal sounders
will stop and the display will show:
3. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
+
If you exceed the entry time the alarm system generates a warning from the internal
sounders and starts the “Second Entry” timer. If you do not unset the alarm system before
the end of the “Second Entry” timer a full alarm condition will occur. If the installation
company has set the “Second Entry” timer to zero the full alarm will occur when the first
entry timer expires.
+
If during the entry procedure the user strays from the prescribed entry route and activates
a detection circuit a full alarm will occur (internal sounders and external sounders). If the
alarm system is fitted with a remote signalling device such as a digicom this will also be
triggered and police action will be taken. However, the alarm system may be
programmed with an “Entry Abort” feature which will allow a further pre-set time delay to
occur if a detection circuit is accidentally triggered during the entry procedure. This will
delay the triggering of the remote signalling device and allow the user time to unset the
system. The delay is normally set to 90 seconds by your installation company.
Full Set Entry Time: __________________
Second Entry Time: __________________
Part-set Entry Time: __________________
Entry Abort Delay: __________________
6
Operating The System TS790 & TS900 User Manual
Enter Your Code
Time left > 0025 0025 0025
SYSTEM OPEN
08:30 Sun 28 Apr OPEN OPEN
ABC SECURITY
08:30 Sun 28 Apr 08:30 08.30
Intelligent Security & Fire Ltd

Part-Setting Using The Part-Set Buttons
The TS790 & TS900 can have up to three pre-defined part-set configurations. Each configuration
allows the alarm system to set with one or more wards isolated. Each configuration is then
assigned to a part-set button A, B or C, normally this will be done by the installation company at
the time of commissioning. However the master user may also configure the part-set buttons,
providing the installation company has programmed the alarm system to allow this facility (see
“Part Set Groups on page 39).
»To part-set the alarm system, proceed as follows:
1. Enter your passcode XXXX. The
display will show:
2. Within 5 seconds press the required
part-set button A,Bor C, e.g., press Afor
part-set A. The display will show:
3. The exit sounder will start. If necessary
leave the area via the prescribed exit route.
The display will show the remaining exit time,
e.g.,
4. The system will be part-set when the exit
time has expired, on activation of the Final
Exit circuit or by pressing the Exit Terminator
button, as appropriate. When the system is
part-set the display will show the wards that
are set and the time, e.g.,
+
The text shown on the LCD remote keypads at step (2) may be programmed by the
master user (see “Edit Text for Part-Set Groups” on page 41). If the text is not programmed
the display will read the default “Part Set group A” for the above example.
+
If the alarm system has LED remote keypads fitted, the installation company may have
programmed the the system so that the alternating displays shown at step (4) only show
the time.
Part-Set A: _________________________________________________________
Setting Mode: Timed o Final Exit o Exit Terminator o Instant o
Part-Set B: _________________________________________________________
Setting Mode: Timed o Final Exit o Exit Terminator o Instant o
Part-Set C: _________________________________________________________
Setting Mode: Timed o Final Exit o Exit Terminator o Instant o
7
TS790 & TS900 User Manual Operating The System
Press ENT to
Select Function FUNCTION Func.
Setting the
Office Area Only P. SET A PS.A
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ A ]
05:30 Sun 28 Apr PART SET P.SET
AA
05.30 05.30
Intelligent Security & Fire Ltd

Part-Setting With Part Set Passcodes
Passcode types “Code Set Group A”, “Code Set Group B”, “Code Set Group C”, and the “Full Set
Group” enable the user to set and unset only the wards assigned to their “Code Set Group”. The
“Code Set Groups” are configured by the master user or installation company (see “Code Set
Groups” on page 40).
The following example shows how to set and unset wards A and B using the passcode type
“Code Set Group A”. The example first assumes that the alarm system is initially unset.
»To set your area(s) using a “Code Set Group” passcode, proceed as follows:
1. Enter your “Code Set Group” passcode
XXXX. The exit sounder will start. If
necessary leave the area via the prescribed
exit route. The display will show the
remaining exit time, e.g.,
2. The system is part-set when the exit time
has expired, on activation of the Final Exit
circuit or by pressing the Exit Terminator
button, as appropriate. When the system
has part-set the display will show the wards
that are set and the time e.g.,
»To unset your area(s), proceed as follows:
1. Enter the area or premises via the
prescribed entry route and proceed directly
to the remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time, e.g.,
2. Enter your “Code Set Group” passcode
XXXXwithin the entry time. The internal
sounders will stop and the display will show:
3. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
The “Code Set Group” passcodes may be used when the system is fully set. When the passcode
is entered only those wards assigned to the “Code Set Group” will be unset.
The following example shows how to unset wards A and B using the passcode type “Code Set
Group A”. The example first assumes that the alarm system is initially full set.
8
Operating The System TS790 & TS900 User Manual
Wards set [ AB ]
05:30 Sun 28 Apr PART SET P.SET
AB AB
05.30 05.30
Please Exit Now.
Time left > 0025 0025 0025
Enter Your Code
Time left > 0025 0025 0025
SYSTEM OPEN
08:30 Sun 28 Apr OPEN OPEN
ABC SECURITY
08:30 Sun 28 Apr 08:30 08.30
Intelligent Security & Fire Ltd

Part-Setting With Part Set Passcodes (Cont.)
»To unset your area(s), proceed as follows:
1. Enter the area or premises via the
prescribed entry route and proceed directly
to the remote keypad. The internal sounders
generate an interrupted tone. The display
will show how much time you have left e.g.,
2. Enter your “Code Set Group” passcode
XXXXwithin the entry time. The internal
sounders will stop and the display will show
the wards that have remained set and the
time, e.g.,
The system may be returned to the full set condition by re-entering the “Code Set Group”
passcode and leaving the area or premises via the prescribed exit route. The system may also
be fully unset at any time by entering a valid passcode (Master, Standard or Holiday).
Code Set Group A: Sets/unsets wards S: o A: o B: o C: o
Code Set Group B: Sets/unsets wards S: o A: o B: o C: o
Code Set Group C: Sets/unsets wards S: o A: o B: o C: o
Full Set Group: Sets/unsets wards S: o A: o B: o C: o
9
TS790 & TS900 User Manual Operating The System
Wards set [S C]
09:30 Sun 28 Apr PART SET P.SET
SC SC
09.30 09.30
Enter Your Code
Time left > 0025 0025 0025
Intelligent Security & Fire Ltd

Silent Setting
The alarm system may be full or part-set such that the internal sounders are switched off during
the exit procedure. However the system will give a short tone at the end of the exit procedure to
indicate that the system has successfully set.
»To full set the alarm system silently, proceed as follows:
1. Enter your passcode XXXX. The
display will show:
2. Within 5 seconds press 8. The display
will show:
3. Leave via the prescribed exit route.
4. The system is full set when the exit time
has expired, on activation of the Final Exit
circuit or by pressing the Exit Terminator
button, as appropriate.
»To part-set the alarm system silently, proceed as follows:
1. Enter your passcode XXXX. The
display will show:
2. Within 5 seconds press the required
part-set button A,Bor C, e.g., press Afor
part-set A then press 8. The display will
show:
3. Leave the area or premises via the
prescribed exit route.
4. The system is part-set when the exit time
has expired, on activation of the Final Exit
circuit or by pressing the Exit Terminator
button, as appropriate.
10
Operating The System TS790 & TS900 User Manual
Press ENT to
Select Functions FUNCTION Func.
Please Exit Now.
Time left > 9999 9999 9999
Press ENT to
Select Function FUNCTION Func.
Setting the
Office Area Only P. SET A PS.A
Intelligent Security & Fire Ltd

Unsetting After An Alarm
If an alarm has occurred whilst the alarm system is full or part-set, the display will indicate the
detection circuit that was triggered when the system is unset. Once the cause of the alarm has
been established the system must be reset (see “Resetting after an alarm”).
1. Enter the premises or area via the
prescribed entry route and proceed directly
to the remote keypad. The internal sounders
will generate an interrupted tone. The
display will show how much time you have
left, e.g.,
2. Enter your passcode XXXXwithin
the entry time. The internal sounders will stop
and the display will show the detection
circuit that caused the alarm, e.g.,
3. Refer to “Resetting after an Alarm”
+
If “Circuit Text” has been programmed then the display on the LCD and Starburst remote
keypads will alternate between the “Circuit number” and the “Circuit Text” at step (2).
Resetting After An Alarm
The installation company will have programmed the system to be either “User Reset”,“Engineer
Reset” or “Remote Reset”, consult your installation company if you are not sure.
User Reset
From step (3) of “Unsetting After An Alarm” proceed follows:
1. Enter your passcode XXXX. The
display will show:
2. Within 5 seconds press ]. The display
will show:
3. After 5 seconds the “SYSTEM OPEN”
message will disappear and the display will
show the time, (date and banner text, LCD
only) e.g.,
Your alarm system is reset by: User: o Engineer: o Remote Reset: o
(Continued Over)
11
TS790 & TS900 User Manual Operating The System
ALARM 03
09:45.59 28/04 ALARM 03 CA.03
Enter Your Code
Time left > 0025 0025 0025
Office Detector
09:45.59 28/04 OFFICE
Press ENT to
Select Functions FUNCTION Func.
SYSTEM OPEN
08:30 Sun 28 Apr OPEN OPEN
ABC Security
08:30 Sun 28 Apr 08.30 08.30
Intelligent Security & Fire Ltd

Engineer Reset
From step (3) of “Unsetting After An Alarm” proceed as follows:
1. The display will cycle between the
detection circuit that caused the alarm and
the “CALL ENGINEER TO RESET SYSTEM”. The
system will also “beep” every minute to
indicate the system requires an engineer to
reset the system. To silence the “beeps”
simply enter your passcode XXXX.
2. Call the installation company to attend
and reset your system.
Tel No._____________________________
+
The display shown at step 2 is programmable and may show something different.
Remote Reset
From step (3) of “Unsetting After An Alarm” proceed as follows:
1. Follow Step (1) of the “Engineer Reset”
procedure.
2. Enter your passcode XXXX.The
display will show:
3. Within 5 seconds press [. “User Menu 1"
is selected, the display will show:
4. Press 3to select the Remote Reset
option. The display will show a random four
digit “Seed Code” e.g.,
5. Write down the “Seed Code”. Telephone
your central station and quote the “Seed
Code”. You will be asked to report the
circumstances of the alarm. If an engineer
is not required to attend site you will be
given a unique four digit “Remote Reset”
code.
Tel No._____________________________
6. Enter the four digit “Remote Reset” code
XXXXthen press [. A muti-tone beep
will confirm acceptance and the display will
return to “User Menu 1":
7. Press ]to return to the Unset condition,
the display will show:
8. After 5 seconds the “SYSTEM OPEN” message will
disappear and the display will show the time, (date
and banner text, LCD only) e.g.,
12
Operating The System TS790 & TS900 User Manual
ALARM 03
09:45.55 28/04 ALARM 03 CA.03
Office Detector
09:45.55 28/04 OFFICE
CALL ENGINEER TO
RESET SYSTEM CALL CALL
ENGINEER ENG.
Press ENT to
Select Functions FUNCTION Func.
User menu 1
Select Option :- USER 1 - 1-
Remote Reset
Quote > 6846 6846 6846
User menu 1
Select Option :- USER 1 - 1-
SYSTEM OPEN
08:30 Sun 28 Apr OPEN OPEN
ABC Security
08:30 Sun 28 Apr 08.30 08.30
Remote Reset
Reply>---- ---- ----
Intelligent Security & Fire Ltd

Setting individual Wards with Standard User Passcodes
The installation company can enable certain standard users to have access to the “Ward
Selection Menu”. This feature allows the user to set individual wards.
»The following example shows how to set wards B and C.
1. Enter your passcode XXXX. The
display will show:
2. Select the setting option as follows:
APart-set A
BPart-set B
CPart-set C
0Ward Selection Menu
NOTE: If an option is not selected after
5 seconds the system will attempt to
full set.
3. Press 0to select the “Ward Selection
Menu”. The display will show:
4. Select / de-select the wards by pressing:
Afor “Ward A”
Bfor “Ward B”
Cfor “Ward C”
0for “Ward S”
e.g., to set wards B and C, de-select
wards S and A. The display will show:
5. When the display shows the required
wards, press [. The exit sounder will start, if
required leave via the prescribed exit route.
The display will show the remaining exit time:
6. When exit tone stops the display will show
the wards that are set and the e.g.,
+
The “Ward Selection Menu” is displayed for a pre-programmed amount of time, which is
programmed by the installation company. If no wards are de-selected at the end of the
pre-programmed time the alarm system will attempt to full set.
13
TS790 & TS900 User Manual Operating The System
Press ENT to
Select Functions FUNCTION Func.
Please Confirm
Set-:SABC SABC SABC
Please Confirm
Set-:**BC --BC --BC
Please Exit Now.
Time left > 0025 0025 0025
Wards set[BC ]
05:30 Sun 28 Apr PART SET P.SET
BC BC
05.30 05.30
Intelligent Security & Fire Ltd

Unsetting individual Wards with Standard User Passcodes
If the installation company has configured the alarm system as described on the previous page
the standard and master users will be given access to the “Ward Selection Menu” when
unsetting the alarm system.
»The following example shows how to unset wards A and B.
1. Enter the premises via the prescribed
entry route and proceed directly to the
remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time:
2. Enter your passcode XXXXbefore
the entry timer expires. The display will show:
3. De-select the wards by pressing:
Afor “Ward A”
Bfor “Ward B”
Cfor “Ward C”
0for “Ward S”
e.g., to unset wards A and B, de-select
wards S and C. The display will show:
4. When the display shows the required
wards, press [. The entry sounder will stop
and the display will show the wards that are
set:
»To unset further wards (assuming wards S and C are set)
1. To unset another ward enter your
passcode XXXX. The display will show:
2. Select the ward(s) you require to unset,
e.g., to unset ward C, de-select ward S. The
display will show:
3. When the display shows the required
ward(s) press [. The display will show the
wards that are set:
14
Operating The System TS790 & TS900 User Manual
Please Confirm
Unset -:SABC SABC SABC
Please Confirm
Unset -:*AB* -AB- -AB-
Wards se t[S C]
05:40 Sun 28 Apr PART SET P.SET
S--C S--C
05.40 05.40
Please Confirm
Unset -:S**C S--C S--C
Please Confirm
Unset -:S*** S--- S---
Wards set [S ]
05:50 Sun 28 Apr PART SET P.SET
SS
05.50 05.50
Enter Your Code
Time left > 0025 0025 0025
Intelligent Security & Fire Ltd

»To Set further Wards (assuming ward S is set)
1. To set other wards enter your passcode
XXXX. The display will show:
2. De-select all wards so that the display
shows:
3. Press [and the display will show:
NOTE: Ward A is not displayed as it is
already set.
4. Select the ward(s) you require to set,
e.g., to set wards B and C, press 0 to
de-select ward S. The display will show:
5. When the display shows the required
wards, press [. The exit sounder will start, if
required leave via the prescribed exit route.
The display will show the remaining exit time:
6. When the system has set the display will
show the wards that are set and the time:
+
If the system is part-set, entry of a valid passcode is assumed to unset rather than set
further wards. To set further wards, it is necessary to unset nothing, the system will then
assume that you require to set further wards.
15
TS790 & TS900 User Manual Operating The System
Please Confirm
Unset -:S*** S--- S---
Please Confirm
Unset -:**** ---- ----
Please Confirm
Set-:S*BC S-BC S-BC
Please Confirm
Set-:**BC --BC --BC
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ ABC]
06:00 Sun 28 Apr PART SET P.SET
ABC ABC
06.00 06.00
Intelligent Security & Fire Ltd

Setting & Unsetting Wards with the Code Set Group Passcodes
If the installation company has enabled the "Ward Selection Menu" for your alarm system, all
users defined as "Code Set Group" users will also have access to the "Ward Selection Menu".
However the users can only select or de-select the wards that have been assigned to their
"Code Set Group", e.g., if "Code Set Group A" is configured to have access to wards A and B,
then when the "Ward Selection Menu" is displayed the user can only select or de-select wards A
and B.
The following example uses "Code Set Group A" which is configured to have access to wards A
and B.
»Setting ward B with "Code Set Group A" passcode (system initially unset)
1. Enter your passcode XXXX, the
display will show:
2. Select the wards you require to set, e.g.,
to set ward B, de-select ward A:
3. When the display shows the required
ward(s) press [. The exit sounder will start, if
required leave via the prescribed exit route.
The display will show the remaining exit time:
4. When the system has set the display will
show the wards that are set and the time:
»Unsetting ward B with "Code Set Group A" passcode (System initially full set)
1. Enter the premises via the prescribed
entry route and proceed directly to the
remote keypad. The internal sounders
generate an interrupted tone. The display
will show the remaining entry time:
2. Enter your passcode XXXXbefore
the entry timer expires. The display will show:
3. Select the wards you require to unset,
e.g., to unset ward B, de-select ward A:
4. When the display shows the required
wards, press [. The entry sounder will stop
and the display will show the wards that are
set:
16
Operating The System TS790 & TS900 User Manual
Please Confirm
Set-:*AB* -AB- -AB-
Please Confirm
Set-:**B* --B- --B-
Please Exit Now.
Time left > 0025 0025 0025
Wards set [ B ]
06:00 Sun 28 Apr PART SET P.SET
BB
06.00 06.00
Please Confirm
Unset -:* A B* -AB- -AB-
Please Confirm
Unset -:**B* --B- --B-
Wards set [SA C]
06:30 Sun 28 Apr PART SET P.SET
SA-C SA-C
06.30 06.30
Enter Your Code
Time left > 0025 0025 0025
Intelligent Security & Fire Ltd