New England Arbors Hanover Trellis VA54230 User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 800 282 9346
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Keystone (1) - 10047
2. Arches ( 2) - 10046
3. Spindles - Short (2) - 10040
4. Spindles - Long (2) - 10041
5. Top Rail (1) - 10580-1
6. Posts (2) - 10583-1
7. Middle Rails (3) - 10582-1
8. Vertical Spindles (5) - 10581-1
9. Bottom Rail (1) - 10584-1
10. 1 1/2”(38 mm) Self-Auguring Stainless Steel Screw (8) - 20016
Tools You Will Need
• Cordless Drill
• Tape Measure
• Level
• Shovel
General Information
•Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ (1.5 m x 2.4 m) for unobstructed assembling.
•You should not need to use excessive force when assembling component.
Hanover Trellis
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
10
Not to Scale
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
V2.2/080117
Ground
5
1
4
2
6
www.newenglandarbors.com
7
3
9
8
77.375 in
197 cm
30 in
76 cm
37 in
94 cm
3.5 in
9 cm

2
Take the arches and snap them onto either side of the
keystone.
Using four screws,fasten the arches to the keystone on both
sides as illustrated.
Note: All screws are self-tapping and require nopre-drilling.
Set aside the assembled arch.
1
2
STEP ONE
Assemble the Top Arch
Hanover Trellis Instructions
Lay out the bottom rail. Insert the verticalspindles into the
precut holes until they “bottom out”.
Slide the three middle rails onto the vertical spindles.
Space the rails approximately 9” (23 cm) apart.
Finish the “ladder” by placing the top rail onto the vertical
spindles.
The top rail has holes on both sides, but the spindles will
not go through it.
1
STEP T WO
Assemble the Trellis
Bottom Rail
(Holes only on top of rail)
1
1
2
3
Middle Rails
(Identical holes on top and bottom of rails)
2
3
2

3
Lay out one post as shown. Align the rails with the pre-routed
holes in the post and push in past the locking tabs. Flip over
and do the same for the other post.
Note: Make sure the long end of each post is facing the same
direction. Once pushed in,the rails will lock into place.
The top rail faces the short end as shown.
Standthe completed panel up and position the arch over
the posts. Slip one of the short spindle into the closest hole
in the top rail as shown. Push the opposite end onto the
nearest arch socket.
Slip one of the long spindles into the next hole in the top rail
as shown. Again,push the opposite end onto the next arch
socket.
Repeat steps 5 and 6 forthe other two spindles.
Note: Pay close attention to the angled ends of each spoke to
ensure a proper fit.
Hold one end of the arch down into the post and secure inplace
with two screws on two sides of the post. Position the screws
directly under the arch cap to ensure proper attachment to the
arch. Repeat for the opposite side.
4
5
STEP T WO
Assemble the Trellis
Hanover Trellis I n structions
6
4
7
75 6

4
TollFree Phone: [phone]
www.newenglandarbors.com
STEP THREE
A
B
C
Install Trellis into Ground
Move the trellisto its final location. When you are satisfied with
the location,mark the positions of the posts,then move the trellis
aside and carefully lay it on its side. Excavate the two postsholes
approximately 12” (30 cm) deep x 5”
(13 cm) diameter.
Insert pressure treated wood into the trellis post. Set the trellis
into position,and use alevel to check the posts. Once you are
satisfied with the orientation, backfill the holes.
Optional: for a sturdier installation,pour concrete into the
excavated holes to hold the posts in place.
www.newenglandarbors.com
C
A
3
5“
(13 cm)
B
12” (30 cm)
Level
24" (61 cm) long Pressure Treated 2x4
(5 cm x 10 cm) or 4x4 (10 cm x 10 cm)
ripped to 3” (7.6 cm) wide
Concrete