New England Arbors Heartwood VA68897 User manual

Heartwood Arbor
VA68897
ASSEMBLY
GUIDE
VER 1.22 11/22/19

GETTING STARTED
First o, allow us to say thank you for the investment you have made in our fine Arbor. This Arbor is designed to be assembled
and installed ideally by two people with basic carpentry knowledge and tools. Do not attempt alone, especially during the
installation stage. When assembling components, place on a non-abrasive surface (ie: shipping box) to avoid scratching. We
recommend a 15’ x 15’ area for unobstructed assembling. You should not need to use excessive force when assembling any
components.
TOOLS YOU WILL NEED
TOOLS YOU MAY NEED
• Framing Square
CAUTION
PLEASE ACKNOWLEDGE THAT THERE SHOULD BE
NO OTHER MATERIALS OR OBJECTS HUNG ONTO
THE RAFTERS OR BEAMS!
Please take the time to read this instruction guide thoroughly prior to
the construction of your arbor. If you have any questions, feel free to
contact our technical dept by calling
North America: 1 800 282 9346 (Mon to Fri 8:00 A.M. to 4:00 P.M. EST).
UK TEL: [phone] - Mon. to Fri. 1:00 PM to 10:00 PM GMT.
WWW.NEWENGLANDARBORS.COM
WWW.NEWENGLANDARBORS.CO.UK

WWW.NEWENGLANDARBORS.COM
WWW.NEWENGLANDARBORS.CO.UK
MATERIALS OVERVIEW 4
MATERIALS BREAKDOWN 5
HAMMER TNUTS INTO ALL FOUR
POSTS
6
ATTACHING ONE RAIL, TWO POSTS
AND LATTICE TOGETHER
7
ATTACHING SECOND RAIL TO
LATTICE AND POST
ATTACHING SUPPORT BEAMS TO
POSTS
ATTACHING BRACES TO SUPPORT
BEAMS
ATTACHING FILTERS TO SUPPORT
BEAMS
ATTACHING METAL STAKES TO
POSTS
SECURING ARBOR INTO GROUND
OPTION 2 STEP 1: DISTANCE
BETWEEN WOOD POSTS
OPTION 2 STEP 3: SECURING
ARBOR INTO CONRETE FOOTINGS
8
9
10
11
12
13
14
15
IN THIS GUIDE

4 VER 1.22 11/22/19
MATERIALS OVERVIEW
1. 12022 - Filters (x6)
1 3/8” x 1” x 29 3/16” (3.50cm x 2.54cm x 75cm)
2. 12023 - Brace Right (x2)
2” x 3 1/8” x 17 7/16” (5cm x 8cm x 44.3cm)
3. 12039 - Brace Left (x2)
2” x 3 1/8” x 17 7/16” (5cm x 8cm x 44.3cm)
4. 12024 - Rail (x4)
1 3/8” x 2” x 15 7/8” (3.50cm x 5cm x 40.32cm)
5. 12025 - Latice (x2)
75 1/2” x 4” (191.76cm x 11cm)
6. 12026 - Post (x4)
2” x 2 3/4 x 85 1/4” (5cm x 7cm x 216.50cm)
7. 12027 - Support Beam (x2)
1” x 4” x 69 13/16” (2.5cm x 10cm x 177.3cm)
1
2
3
4
5
6
7
69 13/16”
(177.3cm)
51”
(129.54cm)
55”
(139.5cm)
88 3/16”
(224cm)
86 13/16”
(220.5cm)
15”
(38.1cm)
20 1/2”
(52.07cm)
29 9/16”
(75cm)
4 3/4”
(12.06cm)

VER 1.22 11/22/19 5
MATERIALS BREAK DOWN
14
23
67
5
12022
FILTERS
X6
12025 LATICE
X2 12026 
POST
X4
12027 SUPPORT
BEAM
X2
12023 BRACE
RIGHT
X2
12039 BRACE
LEFT
X2
12024
RAIL
X4
12028 METAL
STAKE
X4
9
10
11
12
13
20061  BOLT, WASHER, TNUT 2 3/4”
6.98CM X4
20056 SCREW B  2 3/8”6CM
X16
20062  SCREW A  3 1/2” 8.89M
X8
20063 SCREW C  1 3/4” 4.5CM
X12
20064 SCREW D  1 1/4” 3.18CM
X8
8

6 VER 1.22 11/22/19
Step 1
HAMMER TNUTS INTO ALL FOUR POSTS
X4
9

VER 1.22 11/22/19 7
Step 2
ATTACHING ONE RAIL, TWO POSTS AND
LATTICE TOGETHER
3 1/2” 8.89CM X2
1
2
10

8 VER 1.22 11/22/19
Step 3
ATTACHING SECOND RAIL TO LATTICE AND
POST
Repeat steps 2 and 3 for second arbor panel
3 1/2” 8.89CM X2
10

VER 1.22 11/22/19 9
Step 4
Repeat for second beam
ATTACHING SUPPORT BEAMS TO POSTS
2 3/4” 6.98CM X4
9

10 VER 1.22 11/22/19
Step 5
ATTACHING BRACES TO SUPPORT BEAMS
1 3/4” 4.5CM X12
2 3/8” 6CM X4
12
11
12 11
12

VER 1.22 11/22/19 11
Step 6
ATTACHING FILTERS TO SUPPORT BEAMS
2 3/8” 6CM X12
11

12 VER 1.22 11/22/19
Step 7
ATTACHING METAL STAKES TO POSTS
1 1/4”3.18 CM X8
4 3/4”
(12cm)
13

VER 1.22 11/22/19 13
Step 8
SECURING ARBOR INTO GROUND
With a helper and yourself placed on either side, raise the arbor over
desired area and press stakes into ground. This will keep your Arbor
from tipping over.
Depending on how hard your
ground soil is, you may use a mallet
to hammer down each top corner
of your arbor. Make sure to place a
piece of wood over the area where
you will hammer to avoid damage.
!

14 VER 1.22 11/22/19
Option 2
STEP 1: DISTANCE BETWEEN WOOD POSTS
20 1/2 ” (52.07 cm)
outside post to
outside post
17 3/4” (45.08 cm)
centre post to
centre post
55” (139.7 cm)
outside post to
outside post
53” (134.62 cm)
centre post to
centre post
Wood Stakes
String
Determine the area you want to start building your
arbor. At one end of the desired area, hammer one
wooden stake into the ground, tie a piece of string
around it and measure to a length of 55 (139.7cm).
This is where your second wood stake needs to
be hammered into the ground. You have now set
up your wood stakes and ready to dig your holes.
53” (134.62 cm)
Bricks x8 Roll of String Hammer Wood Stakes x4
MATERIALS NEEDED:

VER 1.22 11/22/19 15
Option 2
STEP 2: SECURING ARBOR INTO CONCRETE
FOOTINGS
18”
(48 cm)
6”
(15 cm)
Carefully move your arbor to the side. With
your desired area choosen, measure and
mark the location of posts and dig 4 holes,
18” deep and 6” in diameter.
Place your arbor now in the
excavated holes with a few bricks
or wood pieces under the bottom
rails to keep it level with the ground.
(Only your metal stakes should be
submerged into the ground).
With your arbor in place and secure,
pour concrete 3/4 of the way up in
each hole.
As your first pour of conrete is
almost set, backfill each of the
remaining holes with soil. Let
your concrete cure and set.
1
2
3
4

16 VER 1.22 11/22/19
We’re here
for you.
If you have any questions at all,
don’t hesitate to contact us.
NORTH AMERICA TOLL FREE
18002829346
UNITED KINGDOM
44 2038 687160
Visit our website to chat with a support technician.
WWW.NEWENGLANDARBORS.COM
WWW.NEWENGLANDARBORS.CO.UK