New England Arbors Nantucket Trellis User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 800 282 9346
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Keystone (1)
2. Arches ( 2)
3. Spindles - Short (2)
4. Spindles - Long (2)
5. Top Rail (1)
6. Posts (2)
7. Lattice Channels (2)
8. Diamond Lattice (1)
9. Slotted Half Couplers (4)
10. Bottom Rail (1)
11. 1 1/2”Self-Auguring Stainless Steel Screw (8)
12. 3 /4”Self-Auguring Stainless Steel Screw (18)
Tools You Will Need
• Cordless Drill
• Tape Measure
• Level
• Shovel
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e.shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling component.
Nantucket Trellis
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
V2.1/101815
Ground
5
1
4
2
6
www.newenglandarbors.com
7
3
9
8
10
11
Not to Scale
12
86.5 in
30 in
37 in
12 in
3.5 in

2
Take the arches and snap them onto either side of the
keystone.
Using four long screws,fasten the arches to the keystone on
both sides as illustrated.
Note: All screws are self-tapping and require nopre-drilling.
Set aside the assembledarch.
1
2
STEP ONE
Assemble the Top Arch
Nantucket Tr e llisI nstruction s
Lay out one of the posts and measure 4”from one end and put
a mark on the center of the post as shown.
Center the lattice channel onto the post at the 4” mark. Using
three short screws,fasten the channel to the post at both ends
and in the middle.
Center two of the slotted half couplers against each end of the
lattice channel. Using the pilot holes provided,fasten each
coupler to the post as illustrated.
Note: Make sure the slots in the couplers are facing the
channel.
Repeat steps 1 through 3 for the second post.
1
STEP T WO
Assemble the Trellis
Slot
1
2
3
2
4”
1
2
3

3
Insert the top and bottom rails into the couplers,making sure
the grooves in each rail are facing the lattice channel.
Note: the top rail goes into the couplerwhich isclosest to the
end of the post.
Hold the top rail firmly in place and fasten it to the coupler using
the short screw through the pilot hole provided. Repeat for the
bottom rail.
Slip the lattice into the grooves between the bottom and top
rail. Slide the lattice down towards the post and into the
lattice channel.
Flip the panel over onto the second post. Position the rail ends
over the couplers,and carefully guide the lattice into the lattice
channel. Make sure each rail end is pushedfirmly into the
couplers and secure inplace asshown.
4
5
STEP T WO
Assemble the Trellis
Nantucket Tr e llis Instruction s
6
7
89
4
Slot
5
6
7
Stand the completed panel up and position the arch over the
posts. Slip one of the short spokes into the closest hole in the
top rail asillustrated. Push the opposite end onto the nearest
arch socket.
Slip one of the long spokes into the next hole in the top rail
as illustrated. Again,push the opposite end onto the nextarch
socket. Repeat steps 8 and 9 for the remaining spokes.
Note: Pay close attention to the angled ends of each spoke to
ensure a proper fit.
8
9

4
Toll Free Phone: [phone] Toll Free Fax: [phone]
www.newenglandarbors.com
STEP T WO
10
Assemble the Trellis
www.newenglandarbors.com
C
A
3
5“
B
12”
Level
Concrete
10
Hold one of the arch down into the post and secure in place
using two long screws. Position the screws directly under the
arch cap to ensure proper attachment to the arch. Repeat
for opposite side.
STEP TH REE
A
B
Install Trellis into Ground
Move the trellis to its final location. When you are satisfied
with the location,mark the positions of the posts,then move
the trellis aside and carefully lay it on its side. Excavate the
two posts holes approximately 12” deep x 5” diameter.
Set the trellis into position,anduse a level to check the posts.
Once you are satisfied with the orientation, backfill the holes. Optional: for a sturdier installation,pour concrete into the
excavated holes to hold the posts inplace.
C