New England Arbors Urbanscape Raised Planter Box User manual

General Information
•Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 4’x 8’ (1.2 m x 2.4 m) for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Urbanscape Raised Planter Box
ASSEMBLY INSTRUCTIONS
8
1
Not to Scale
1
2
Ver 1.1/072517
7
www.newenglandarbors.com
www.newenglandarbors.co.uk
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
(UK Tel: [phone] (Mon. to Fri. 1:00 PM to 10:00 PM GMT).
Please read through before starting assembly.
1. Pre-Assembled Side Wall Panels with Posts Connected (2) - 10946
2. Floor Panels (6) - 10947
3. Pre-Assembled Front and Back Wall Panels (2) - 10948
4. Floor Supports (2) - 10949
5. Shelf Boards (7) - 10950
6. Shelf Rails (2) - 10951
7. Post Caps (4) - 10611
4
3
5
6
8.
9.
5/8 (16 mm) Stainless Steel Screws (4) - 20016
1 1/2 (38 mm) Stainless Steel Screws (8) - 20005
9
53.38" (136 cm)
36"
(91 cm)
5.75"
(15 cm)
24"
(61 cm)

Carefully stand the planter box on it’s legs and insert the two floor
supports into place as shown.
The Urbanscape Raised Planter Box
4
Lay down one of the pre-assembled side panel with post down
and insert the bottom shelft as well as the two front and back
panels. Push the bottom shelf until the tabs lock into place.
Align and insert the second pre-assembled side panel as shown.
Push down until the bottom shelf rail tabs lock into place.
3
2
2
STEP ONE
Insert the seven Shelf Boards into the Shelf Rails as shown aside
Note that there are tabs located at the ends of the Shelf Boards.
Push Shelf Boards until tabs are locked into place.
1
The Urbanscape Raised Planter Box
www.newenglandarbors.com
www.newenglandarbors.co.uk
4
2
3
1

The Urbanscape Raised Planter Box
Layout and arrange the floor boards as shown and insert them
one by one starting with either of the shorter floor board.
The boards will be labelled A through F.
Pressure fit the post caps into place. Push until the caps lock into
place.
3
3
2
STEP T WO
Fasten the Pre-assembled side panels to the front and back walls
using two 1 1/2” (38 mm) screws for the bottom rails and one of
the 5/8” (16 mm) screw for the top rail. Repeat for all four corners.
1
1
3
2
B
C
D
E
F
A
AAA

The Urbanscape Raised Planter Box
North America Toll Free Phone: [phone]
United Kingdom Tel: [phone]
www.newenglandarbors.com
www.newenglandarbors.co.uk
Join the two boards together, holding the root of the plant between
the opening of the boards. Carefully lower the boards onto the floor
supports.
To prevent dirt and debris from falling through the gaps, cut a piece of
landscape fabric large enough to fill the base of the planter as well as the sides.
Cut slits in the fabric where the root of the plant is located so that the fabric
can push down to the bottom of the planter and the root ball is not trapped
under the fabric.
3
4
2
STEP T HREE
To plant a hanging plant, remove two boards at a time and place the
stem between the two boards as shown.
1
1
2
4
Fill the planter box with planting soil. Note to hold the landscape fabric
against the inner walls while filling the planter box with soil. Trim excess
fabric if necessary.
Smaller plants such as herbs could also be planted above the planter box.
4