New England Arbors Hanover User manual

Part # Description Quantity
Assembly & Mounting Instructions
Hanover Trellis
- Read instructions through carefully before
beginning assembly.
- Identify each component from material list.
- When assembling components, place on a
non-abrasive surface to avoid scratches.
- Do not use excessive force when assembling
components.
- In the event of missing or defective parts,
please call our customer service department
at 1-800-282-9346 (ext.#20).
General Information:
- Cordless drill with #2 Robertson
bit
- Tape measure
- Level
- Shovel
- Pencil
Tools Required:
- Pre-mix concrete (recommended for added stability).
Materials Included:
Materials (Optional):
(Fig. 1)
Product dimensions & part
identification.
(Fig. 2)
Post layout for installation.
1 3 1/2” sq.. x 58” Posts
2 1 3/4” sq. x 36 3/4” Top
3 1 3/4” sq. x 36 3/4” Middle rail
4 7/8” x 1 1/2” x 19 5/8” Spokes
5 7/8” x 1 1/2” x 15 5/8” Spokes
6 1 3/4” sq x 36 3/4” Bottom rail
7 Keystone
8 Arches
9 7/8“ x 1 1/2” x 43 1/4“ side spindle 5
10 Hardware kit (Includes):
3/4” Self-tapping stainless screws 8
2
1
3
2
2
1
1
1
30”
Ver 1.07
- Pressure treated 2x4 or 4x4 2 ft long ripped to
3”wide

1
3
4
5
6
2
7
9
8
Take the arches (part 7) and snap them onto either side of the
keystone (part 6).
Using four screws, fasten the arches to the keystone on both
sides as illustrated (arrows show each screw location). Note: all
screws are self-tapping and require no pre-drilling. Set aside
the assembled arch.
Lay out the bottom rail (part #6). Insert the side spindles (
part #9) into the precut holes until they “bottom out”.
Slide the three middle rails (part #3)onto the side spindles.
Space the rails approximately 9” apart.
Finish the “ladder” by placing the top rail
(part #2) onto the side spindles.
The top rail is has holes on both sides, but the spindles will not
all go through it.
Hold one end of the arch down into the post and secure in place
with two screws on two sides of the post. Position the
screws directly under the arch cap to ensure proper
attachment to the arch. Repeat this for the opposite side.
Slip one of the long spokes (part 4) into the next hole in the top
rail as illustrated. Again, push the opposite end onto the next
arch socket. Repeat steps 10 and 11 for the remaining spokes.
Note: pay close attention to the angled ends of each spoke, to
ensure a proper fit.
Stand the completed panel up and position the arch over the
posts. Slip one of the short spokes (part 5) into the closest hole
in the top rail as illustrated. Push the opposite end onto the
nearest arch socket.
Lay out one post (part #1). Align the rails with the pre-routed holes
in the post and push in past the locking tabs. Flip over and do the same
for the other post.
Note: make sure the long end of each post is facing the same direction.
The rails do not come out. The top rail faces the short end.
10
Dig two 12” deep holes in the desired location using the
distance shown in (Fig. 2) on the front cover. Insert pressure
treated wood into the trellis post. Set the trellis into
postion, and use a level to check the posts. Once you are
satisfied with the orientation, fill in the holes. For added
stabitily in high wind or high traffic areas, we recommend using
pre-mix concrete (not included).
If you have any questions concerning the assembly or installation of this product and require assistance, please call our Customer service
department at 1-800-282-9346 (ext.#20), Weekdays from 8:00 am. to 4:00 pm. Eastern standard time.
If you have any comments or suggestions about our product or service, please let us know! Call: 1-800-282-9346 (ext.#20). or E-mail:
[email protected]
To learn more about us, visit us on the web at: www.newenglandarbors.com
Questions ? :