New Rock Technologies MX100G User manual

New Rock Technologies, Inc.
MX100G SIP-ISDN Gateway Series
User Manual
MX100G
MX100G-S
Website: http://www.newrocktech.com
Email: [e-mail]
Document Version: 201706

Amendent Records
Document Rev. 01(June, 2017)
This document is applicable for V115.
Copyright © New Rock Technologies, Inc. 2017. All rights reserved.
All or part of this document may not be excerpted, reproduced and transmitted in any form or by any
means without prior written permission from the company.

Contents
Amendent Records.......................................................................................................................................... 2
Contents ........................................................................................................................................................... 3
Contents of Figure........................................................................................................................................... 5
Contents of Table ............................................................................................................................................ 7
1 Overview..................................................................................................................................................... 1-1
1.1 Product Introduction...........................................................................................................................................1-1
1.2 Features.............................................................................................................................................................1-1
1.3 Equipment Structure..........................................................................................................................................1-2
1.3.1 Front & Back Panel.................................................................................................................................1-2
1.3.2 CON Port................................................................................................................................................1-5
1.3.3 Specifications .........................................................................................................................................1-6
2 Installation Preparation............................................................................................................................. 2-8
2.1 Installation Precautions......................................................................................................................................2-8
2.2 Site Requirements .............................................................................................................................................2-8
2.2.1 Temperature and Humidity.....................................................................................................................2-8
2.2.2 Cleanliness.............................................................................................................................................2-8
2.2.3 Power Supplier.......................................................................................................................................2-9
2.2.4 Grounding...............................................................................................................................................2-9
2.2.5 Electromagnetic Environment.................................................................................................................2-9
2.2.6 Other Facilities........................................................................................................................................2-9
2.3 Opening Inspection..........................................................................................................................................2-10
3 Installation.................................................................................................................................................. 3-1
3.1 Tools and Meters...............................................................................................................................................3-1
3.2 Rack Mounting...................................................................................................................................................3-1
3.2.1 Attaching the Brackets............................................................................................................................3-1
3.2.2 Mounting the Gateway............................................................................................................................3-1
3.3 Installing Cables.................................................................................................................................................3-2
3.3.1 Connecting Console Port........................................................................................................................3-2
3.3.2 Connecting the Ethernet Cable...............................................................................................................3-3
3.3.3 Connecting the T1/E1 Cable...................................................................................................................3-3
3.3.4 Connecting the Grounding Cable ...........................................................................................................3-4
3.3.5 Connecting the Power Cord....................................................................................................................3-4
3.3.6 Verifying Installation ...............................................................................................................................3-5
4 Powering up the Gateway......................................................................................................................... 4-1
4.1 Verification before Power-up..............................................................................................................................4-1
4.1.1 Checking Appearance ............................................................................................................................4-1
4.1.2 Checking Power Supply..........................................................................................................................4-1
4.2 Powering up the Gateway..................................................................................................................................4-1

5 Parameter Setting...................................................................................................................................... 5-1
5.1 Login..................................................................................................................................................................5-1
5.2 Buttons Used on Gateway Management Interface.............................................................................................5-2
5.3 Basic Configuration............................................................................................................................................5-2
5.3.1 Network Configuration............................................................................................................................5-2
5.3.2 STUN (RFC3489)...................................................................................................................................5-3
5.3.3 VLAN......................................................................................................................................................5-5
5.3.4 System Configuration .............................................................................................................................5-5
5.3.5 SIP Configuration ...................................................................................................................................5-7
5.3.6 SIP Trunk................................................................................................................................................5-9
5.3.7 ISDN Configuration...............................................................................................................................5-10
5.3.8 FoIP......................................................................................................................................................5-11
5.4 ISDN................................................................................................................................................................5-12
5.5 Routing ............................................................................................................................................................5-16
5.5.1 Digit Map ..............................................................................................................................................5-16
5.5.2 Routing Table.......................................................................................................................................5-18
5.5.3 Application Examples of Routing Table................................................................................................5-22
5.6 Advanced Configurations.................................................................................................................................5-23
5.6.1 System..................................................................................................................................................5-23
5.6.2 Media Stream.......................................................................................................................................5-25
5.6.3 SIP Configuration .................................................................................................................................5-27
5.6.4 RADIUS................................................................................................................................................5-29
5.6.5 Tones....................................................................................................................................................5-29
5.6.6 System time..........................................................................................................................................5-31
5.7 Security............................................................................................................................................................5-33
5.7.1 Access Security....................................................................................................................................5-33
5.7.2 Access list.............................................................................................................................................5-34
5.7.3 Voice Security.......................................................................................................................................5-35
5.7.4 Encryption.............................................................................................................................................5-36
5.8 Call Status .......................................................................................................................................................5-37
5.9 Log Management.............................................................................................................................................5-38
5.9.1 System Status ......................................................................................................................................5-38
5.9.2 Call Message........................................................................................................................................5-39
5.9.3 ISDN Status..........................................................................................................................................5-40
5.9.4 System Startup.....................................................................................................................................5-41
5.9.5 Manage Log..........................................................................................................................................5-41
5.10 System Tool...................................................................................................................................................5-42
5.10.1 Configuration Maintenance.................................................................................................................5-42
5.10.2 Upgrade..............................................................................................................................................5-42
5.10.3 Restore Factory Settings....................................................................................................................5-44
5.10.4 IP Capture ..........................................................................................................................................5-44
5.10.5 Reboot................................................................................................................................................5-44
5.11 Version Information........................................................................................................................................5-44
5.12 Logout............................................................................................................................................................5-45

Contents of Figure
Figure 1-1 Front Panel.............................................................................................................................................1-2
Figure 1-2 Back Panel (AC).....................................................................................................................................1-4
Figure 1-3 Back Panel (DC).....................................................................................................................................1-5
Figure 1-3 RJ45 to RS232 serial cable....................................................................................................................1-6
Figure 1-4 USB to RS232 converter cable...............................................................................................................1-6
Figure 3-1 Installation of MX100G Series L-shape Brackets ...................................................................................3-1
Figure 3-2 Mount MX100G to Rack .........................................................................................................................3-2
Figure 3-3 Cable of Connecting MX100G CON.......................................................................................................3-3
Figure 3-4 Connecting the T1/E1Cable....................................................................................................................3-4
Figure 5-1 Login Interface for MX100G Gateway Configuration ..............................................................................5-1
Figure 5-2 Network Configuration Interface.............................................................................................................5-2
Figure 5-3 STUN configuration interface..................................................................................................................5-4
Figure 5-4 VLAN Configuration Interface.................................................................................................................5-5
Figure 5-5 System Configuration Interface ..............................................................................................................5-6
Figure 5-6 SIP Configuration Interace......................................................................................................................5-7
Figure 5-7 SIP Trunk Settings Interface...................................................................................................................5-9
Figure 5-8 ISDN Configuration Interface................................................................................................................5-10
Figure 5-9 FoIP Configuration Interface.................................................................................................................5-11
Figure 5-10 ISDN Configuration Interface..............................................................................................................5-12
Figure 5-11 Configuration Interface for Digit Map..................................................................................................5-17
Figure 5-12 Configuration Interface for Routing Table...........................................................................................5-19
Figure 5-13 System Advanced Configuraiton Interface..........................................................................................5-24
Figure 5-14 Media Stream Configuration Interface................................................................................................5-26
Figure 5-15 SIP Related Configuration Interface ...................................................................................................5-27
Figure 5-16 RADIUSConfiguration Interface..........................................................................................................5-29
Figure 5-17 Tones Configuration Interface ............................................................................................................5-30
Figure 5-18 Clock Service Interface.......................................................................................................................5-31
Figure 5-19 Access Configuration Interface .....................................................................................................5-33
Figure 5-20 Access list configuration Interface......................................................................................................5-35
Figure 5-21 Voice Security Configuration Interface ...............................................................................................5-36
Figure 5-22 Encryption Configuration Interface .....................................................................................................5-36
Figure 5-23 ISDN Status Interface.........................................................................................................................5-37
Figure 5-24 System Status Interface......................................................................................................................5-38
Figure 5-25 Call Message Interface.......................................................................................................................5-39
Figure 5-26 ISDN Status Interface.........................................................................................................................5-40
Figure 5-27 System Startup Interface....................................................................................................................5-41
Figure 5-28 Manage Log Interface.........................................................................................................................5-41
Figure 5-29 Configuration Importing or Exporting Interface...................................................................................5-42
Figure 5-30 Upgrade Interface...............................................................................................................................5-43
Figure 5-31 Upgrading interface by .img file..........................................................................................................5-43
Figure 5-32 Upgrade Interface...............................................................................................................................5-43
Figure 5-33 Ethereal interface ...............................................................................................................................5-44
Figure 5-34 Version Information Interface..............................................................................................................5-45

Contents of Table
Table 1-1 Front Panel..............................................................................................................................................1-3
Table 1-2 Indicators.................................................................................................................................................1-3
Table 1-3 Pinouts of Ethernet Ports.........................................................................................................................1-4
Table 1-4 Pinouts of T1/E1 Module..........................................................................................................................1-4
Table 1-5 Description of Back Panel........................................................................................................................1-4
Table 1-6 Description of Back Panel........................................................................................................................1-5
Table 1-7 Standard Table for Lead Wire of Pin at Configuration Port (CON)...........................................................1-5
Table 1-8 Attributes of CON Port.............................................................................................................................1-6
Table 1-9 Specifications...........................................................................................................................................1-6
Table 2-1 Standard Configuration..........................................................................................................................2-10
Table 5-1 Network Configuration Interface ..............................................................................................................5-3
Table 5-2 STUN parameters....................................................................................................................................5-4
Table 5-3 VLAN Configuration Parameters..............................................................................................................5-5
Table 5-4 System Configuration Parameters...........................................................................................................5-6
Table 5-5 Codec Methods Supported by Gateway ..................................................................................................5-7
Table 5-6 SIP Configuration Parameters.................................................................................................................5-8
Table 5-7 SIP Trunk Parameters .............................................................................................................................5-9
Table 5-8 ISDN Configuration Parameters ............................................................................................................5-10
Table 5-9 FoIP Configuration Parameters .............................................................................................................5-11
Table 5-10 ISDN Configuration Parameters ..........................................................................................................5-13
Table 5-11 Operated Numbers and Translation Rules...........................................................................................5-15
Table 5-12 Description of Digit map.......................................................................................................................5-17
Table 5-13 Routing Table Format..........................................................................................................................5-20
Table 5-14 Number Transformations.....................................................................................................................5-20
Table 5-15 Routing Destination .............................................................................................................................5-22
Table 5-16 Advanced System Configuration Parameters......................................................................................5-24
Table 5-17 Media Stream Configuration Parameters.............................................................................................5-26
Table 5-18 SIP Related Configuration Parameter..................................................................................................5-27
Table 5-19 RADIUS Configuration Parameter.......................................................................................................5-29
Table 5-20 Tones Configuration Parameters.........................................................................................................5-30
Table 5-21 Clock Service Parameters ...................................................................................................................5-32
Table 5-22 Access security setting parameters .....................................................................................................5-34
Table 5-23 Encryption Configuration Parameters..................................................................................................5-36
Table 5-24 Status Parameters...............................................................................................................................5-38
Table 5-25 System Status Parameters..................................................................................................................5-39
Table 5-26 ISDN Status Parameters......................................................................................................................5-40
Table 5-27 Manage Log Parameters .....................................................................................................................5-41

MX100G SIP-ISDN Gateway Series User Manual
www.newrocktech.com 1-1
1 Overview
1.1 Product Introduction
The MX100G and MX100G-S SIP-ISDN trunking gateway (hereinafter the MX100G) is a VoIP product
series developed by New Rock Technologies Inc. It uses the SIP and T1/E1 interfaces for the
inter-conversion of IP packets and PCM signals, allowing the interworking of the IP-based
new-generation voice network to legacy Public Switched Telephone Network (PSTN), and the private
branch exchange (PBX) of an enterprise.
As a carrier-class VoIP gateway, the MX100G is designed under the requirements of telecom operators,
integrators, value-added service providers as well as large and medium-sized enterprises for VoIP
services. The MX100G has distinctive advantages over other similar products in terms of performance,
system reliability, compatibility and cost performance. In addition, the MX100G has efficient
software/hardware architecture and powerful DSP processing capabilities, ensuring the realization of
major functions (including the conversion between PCM signals and IP packets, G.711 or G.729A
encoding and decoding of voice signal, and echo cancellation, etc.) even under full load conditions.
By supporting the ISDN PRI signalling, the MX100G can control its calls with the PSTN or PBX. The
call control between the MX100G and media gateway controller (softswitch) is carried out through
Session Initiation Protocol (SIP). By now, the MX100G has successfully passed the interoperability test
with various popular softswitch platforms and IP PBX products.
1.2 Features
The MX100G has the following characteristics:
High performance
The DSP chip with powerful voice processing used by the MX100G is developed by the TI Company. Its
DSP daughter card ensures a 6000 MIPS processing capability for each gateway, enabling the MX100G
to provide functions of voice signal processing (G.711, G.729A, and G.723.1), echo cancellation, and fax
relay (T.38) under full load conditions (120 calls).
High security
To ensure security, the MX100G-S supports SSH and HTTPS for remote access, and provides functions
including signaling and media stream encryption, automatic password strength test, brute-force password
cracking prevention, cipher text data storage, access whitelist, and system log backup.
High reliability
The MX100G-S provides high-availability features including 1+1 redundancy of Ethernet ports and
AC/DC power supplies (optional), and SIP registration failover.

User Manual MX100G SIP-ISDN Gateway Series
1-2 www.newrocktech.com
Remote Management and Maintainability
The New Rock Cloud client inside the MX100G-S allows the MX100G-S located behind an enterprise
NAT or firewall to be accessed across Internet securely. Real-time monitoring, alarm notification, remote
packet capture and software upgrades can be performed with the New Rock Network Management
System or third-party element management systems with TR-069.
Low cost and high reward
How to reduce cost and investment risk is one of the major challenges a user faces when choosing an
IP-based new generation of voice device. The MX100G helps reducing users’ cost by increasing new
functions and applications to follow the ongoing evolution of VoIP technologies. This can be realized
through New Rock’s software upgrade free of charge policy within the life cycle of the MX100G.
In support of multiple protocols
The MX100G supports different kinds of protocols including Session Initiation Protocol (SIP), Real-time
Transport Protocol (RTP), Trivial File Transfer Protocol (TFTP), File Transfer Protocol (FTP), Hypertext
Transfer Protocol (HTTP), Session Traversal Utilities for NAT (STUN), Also, the MX100G supports
different technologies including ISDN PRI signalling, G.711, G.729A, or G.723.1 encoding and decoding,
G.168 echo cancellation, Dual-Tone Multi-frequency (DTMF) message transmission (RFC 2833), and fax
relay (T.38).
High interoperability
By now, the MX100G has successfully passed the interoperability test with various softswitch platforms
and IP PBX products.
1.3 Equipment Structure
1.3.1 Front & Back Panel
Figure 1-1 Front Panel

MX100G SIP-ISDN Gateway Series User Manual
New Rock Technologies, Inc. 1-3
Table 1-1 Front Panel
#
Mark
Description
①
RST
Pressing the RST button for less than three seconds: no action will be taken.
Pressing the RST button for more than three seconds: the factory settings will be restored.
②
PWR
Indicators for power supply, system status and alarm, respectively.
③
STU
④
ALM
⑤
CON
A configuration interface.
⑥
ETH
Specifies an RJ45 module interface.
Interfaces ETH1 and ETH2 share the same IP address for allowing access to the external
network. Dual-LAN redundancy is supported.
⑦
AUX
An RJ45 interface.
Interfaces AUX1 and AUX2 share the same IP address for local management and
configuration.
⑧
T1/E1
An RJ45 interface, in support of 1 T1/E1, 2 T1/E1, and 4 T1/E1. Each T1 interface
supports the maximum 24 voice channels; each E1 interface supports the maximum 30
voice channels with ISDN PRI signalling.
⑨
SD
A SD card socket.
Table 1-2 Indicators
Mark
Function
Status
Description
PWR
(red,
green)
Power
Indication
Steady green
The power supply is working.
Off
No power supply.
Steady red
The power supply is abnormal.
STU
(red,
green)
Status
Indication
Off
The device is locked.
Blinking red
System is in a diagnostic mode and you can execute limited operation
(e.g. Log in to system through Telnet)
Steady Red
The device is starting.
Blinking green
System is operating normally
ALM
(red,
green)
Alarm
Indication
Steady green
No alarms
Blinking red
Device startup failure
Steady red
Network failure or app exited
ETH/
AUX
Interface state
indicator
Steady green
(right side)
The transmit speed is 1000M bit/s.
Off
(right side)
The transmit speed is 10M bit/s or 100M bit/s.
Steady green
(left side)
The link has been established but no service traffic is transmitted.
Blinking green
(left side)
Service traffic is being transmitted on the link.
Off
(left side)
The link is not established.
T1/E1
Interface state
Steady green
The connection works normally.

User Manual MX100G SIP-ISDN Gateway Series
1-4 www.newrocktech.com
Mark
Function
Status
Description
(red,
green)
indicator
Blinking red
A remote alarm is generated.
Steady red
A local alarm is generated.
Off
No connection is established.
Table 1-3 Pinouts of Ethernet Ports
RJ45 Pin-out
1
2
3
6
Description
TX+
TX-
RX+
RX-
Table 1-4 Pinouts of T1/E1 Module
RJ45 Pin-out
1
2
3
4
5
6
7
8
Description
RX Ring
RX Tip
NC
TX Ring
TX Tip
NC
NC
NC
Figure 1-2 Back Panel (AC)
Table 1-5 Description of Back Panel
#
Description
①
AC power socket, 100-240 VAC voltage input.
②
Ground pole.

MX100G SIP-ISDN Gateway Series User Manual
New Rock Technologies, Inc. 1-5
Figure 1-3 Back Panel (DC)
Table 1-6 Description of Back Panel
#
Description
①
DC power socket, -36 to -72 VDC voltage input.
②
Ground pole.
1.3.2 CON Port
The MX100G provides one configuration interface (CON) of RJ45 interface for local management and
debugging.
Table 1-7 Standard Table for Lead Wire of Pin at Configuration Port (CON)
Pin number of RJ45 plug
1
2
3
4
5
6
7
8
Description
NC
NC
TXD
GND
GND
RXD
NC
NC
Pairing connection with DB9
female plug
2
5
3
Pairing connection with DB25
male plug
3
7
2
The configured interface is connected to the RS232 port on the PC, allowing the PC to establish the
connection with the MX100G by configuring a terminal emulator. The configured interface of MX100G
is in a 3-wire configuration: one TXD (data transmission terminal), one RXD (data reception terminal),
and one GND (ground terminal).
Please use a RJ45 to RS232 serial cable as shown in Figure 1-3 for connecting the CON port on MX100G
side and the RS232 port on PC side. If the connection is established between MX100G and the mobile PC
with no RS232 ports, please use the cable together with USB to RS232 converter cable as shown in
Figure 1-4.

User Manual MX100G SIP-ISDN Gateway Series
1-6 www.newrocktech.com
Figure 1-3 RJ45 to RS232 serial cable
Figure 1-4 USB to RS232 converter cable
Table 1-8 Attributes of CON Port
Attributes
Description
Connector
RJ45
Interface count
1
Interface standard
RS232
Baud rate
115200
Data bit
8
Parity
No
Stop bit
1
Traffic control
No
1.3.3 Specifications
Table 1-9 Specifications
Item
Description
Basic
Ethernet
RJ45, 4×10/100/1000M Base-T, self-adaptive
E1/T1Interface
4, 120 simultaneous VoIP calls
SD Interface
1
CON Interface
RJ45
System Memory
256MB
System Flash
32MB
Processor
TI AM3352
DSP
TI C5509
Single/Dual AC power supplies
~100 to 240V, 50/60Hz, 1A
Single/Dual DC power supplies
-36 to -72 VDC, 2.5A
Power Consumption
18 W (Max)
Size (H×W×D)
44×440×300 mm,1U formfactor
Weight
net weight:3 kg gross weight(with box):5 kg
Environment Requirements
Operating Environment
0 to 40oC, Non-Condensing Humidity 10 to 95%
Storage Environment
-10 to 60oC, Non-Condensing Humidity 10 to 95%

MX100G SIP-ISDN Gateway Series User Manual
New Rock Technologies, Inc. 1-7

User Manual MX100G SIP-ISDN Gateway Series
2-8 www.newrocktech.com
2 Installation Preparation
For avoidance of personal injury and device damage, please read this chapter carefully before installation.
2.1 Installation Precautions
For your safety, please follow the precautions when MX100G is installed and used.
Keep the site far from the heat and humidity
Take precautions with use of high-voltage electricity
Please let the experienced or trained operator to install and maintain MX100G
Wear static discharge wrist strap
Ensure the proper electric ground of installed equipment
Properly connect the power cable to MX100G
Do not plug the power cable when in use
UPS is advised
2.2 Site Requirements
2.2.1 Temperature and Humidity
Check the temperature and humidity of equipment room. To ensure the normal operation and long service
life of the gateway, the temperature and humidity in the room should be kept at the proper range.
The humidity in the equipment room should be kept between 10% and 90% (non-condensing). Abnormal
humidity condition may cause problems to the gateway:
Long term high humidity may lead to bad insulation and even cause electricity leakage, mechanical
property change and corrosion.
Low humidity is likely to leave captive screws to loose due to static electricity built up and the
insulation washer shrunk.
The temperature in the equipment room should be kept between 0oC and 40oC. Abnormal temperature
condition may cause problems to the gateway:
High temperature acceralets aging of electrical parts and insulation materials.
Low temperature, however, may destabilize the operation of gateway.
2.2.2 Cleanliness
Dust is very harmful to the safe operation of the gateway. Dust that is adsorbed by static electricity acts as
insulator, which not only affects the service life of the gateway but also leads to communication failure.
Therefore, the room for the gateway must be kept clean.

MX100G SIP-ISDN Gateway Series User Manual
New Rock Technologies, Inc. 2-9
To ensure adequate ventilation to keep the gateway from overheating, there should be adequate clearance
for the air intake and the air exhaust vents. Keep at least 6 cm clearance at the left and right side of the
chassis where the air intake is and at least 15 cm clearance at the rear of the chassis where the exhaust
vents located.
The rack for MX100G should have a good ventilation system.
2.2.3 Power Supplier
Check the power supply system against the electrical specification of the gateway.
2.2.4 Grounding
For AC power supply system
To maintain good voice quality, proper grounding of the AC supply is critical to minimize the noise from
the AC interference. Therefore, the following conditions must be ensured:
The AC power outlet has a protection ground contact.
The ground contact of AC supplier must be grounded properly.
Avoid sharing the multi-outlet power strip with other devices that may generate electrical interference.
MX100G is chassis based with ground tab.
In a site that can provide ground for the chassis, the ground tab at the rear panel of chassis for MX100G
must be properly grounded.
For DC power supply system
The DC power working ground (the positive pole of the -48 V DC power supply or negative pole of the
24 V DC power supply) of the communications site should be connected with the indoor collective
grounding cables nearby. The grounding cables should meet the requirement for the maximum load of the
equipment.
The power supply equipment of the communications site should be connected with from the collective
ground cable in the communications building (or from the protection grounding bar of the equipment) to
the DC working ground cable.
2.2.5 Electromagnetic Environment
Any possible interference source, wherever it is from, impacts the gateway negatively. To resist the
interference, make sure that:
Keeping the gateway far from radio transimitting station, radar station, and high-frequency devices.
Use electromagnetic shielding when necessary.
The gateway is capable for secondary lighten protection on wires and cables that connected to outside
buildings.The site must provide the primary lighten protection.
The power supply system should be used independently as much as possible and effective measures of
preventing electric grid from interference should be adopted.
Ensure a good power grounding effect of equipment or add a lightning protector.
2.2.6 Other Facilities
Rack/Workbench

User Manual MX100G SIP-ISDN Gateway Series
2-10 www.newrocktech.com
MX100G is designed to be installed in a standard 19-inch rack, which should provide adequate
air-flow to cool down the gateway, and should be firm enough to support the weight of the gateway. It
is also recommended the rack is earth grounded properly.
PSTN Line
If the gateway is equipped with T1/E1 interface, be sure to subscribe PSTN lines from local telephone
company and activate the lines prior to the installation.
IP Network
The gateway is connected to IP network through its 10/100/1000 base-T Ethernet port and
communicate with other equipments through the network. Inspect IP network on the site, including
router, switch, cable wiring and etc, and make sure they are ready for the gateway.
AC Power Outlets
The gateway needs AC power supply, and sometimes the power is provided through a power strip
with extension cord. Verify that each socket outlet on the power strip is equipped with protective earth
contact and the protective action is not negated by using extension power cord.
2.3 Opening Inspection
After the completion of installation preparation, you should open the box for inspection. Make sure the
gateway and all in-box accessories match the description below.
An MX100G with basic configuration should include components as shown in fowling table.
Table 2-1 Standard Configuration
Description
Quantity
Unit
MX100G
1
Set
Rack Mounting Kits
1
Set
T1/E1 Cable
1/2/4
Set
Power Cord (AC or DC)
1 or 2
Note: 2 for dual power supplies
Set
Grounding Cable
1
Set
The package list is only for reference. Changes may be made without notification. The detailed
inclusions are on the shipping list enclosed in the device package. Please contact your supplier if you
have any question.

MX100G SIP-ISDN Gateway Series User Manual
www.newrocktech.com 3-1
3 Installation
3.1 Tools and Meters
Screwdriver
Antistatic wrist strap
Ethernet and console port cables
Power cable
Terminals (a PC running terminal program can be used)
Universal electric meter
Multimeter
3.2 Rack Mounting
The MX100G series chassis are designed to be mounted on a standard 19-inch rack with 1U height.
3.2.1 Attaching the Brackets
Place the MX100G series chassis on the workbench, take two L-shape rack mounting brackets and screws,
install the brackets at the left and right sides of the equipment, as shown in the fowling figure.
The L-shape brackets are used to secure the gateway to the rack. The brackets cannot support the weight
of the equipment alone. Prior to install the MX100G series chassis into rack, a supporting shelf must be
installed in place where the gateway will sit.
Figure 3-1 Installation of MX100G Series L-shape Brackets
3.2.2 Mounting the Gateway
Attention should be paid during the installation:
Ensure that the rack is firmly attached to the ground and stable.
If the gateway is installed in a closed cabinet shelf, the cabinet must provide adequate air-flow so the
equipments inside can be well ventilated.
If multiple gateways are installed in a rack, it is recommended to keep at lease 1/2U space between
gateways for heat dissipation.

User Manual MX100G SIP-ISDN Gateway Series
3-2 www.newrocktech.com
Follow the steps to install the gateway:
Place the gateway on a shelf in the rack.
Slide it to a proper position along the guide rails.
Fix the rack-mount brackets to the rack posts with supplied Phillips screws. Make sure that the
gateway is in level position and securely fixed as shown in fowling figure.
Figure 3-2 Mount MX100G to Rack
3.3 Installing Cables
3.3.1 Connecting Console Port
A CON should be provided by MX100G to check errors of the device. Connect the CON with computer’s
RS232 serial ports, then local computers can interwork with the device through simulating terminal
program.
As to MX100G, RJ45 Plug is used. One port is applied for connecting CON, while the other is applied for
DB9 Adapter to insert serial ports of configuration terminal. CON Ratio: 115200.
Console Port cable installation procedure is as followed:
Step1 Choose a terminal (PC).
Step2 Power off the terminal and connect RS232 port with the Console port.