Next ANTOINETTE 781396 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Please do not apply adhesive substrates to the product, e.g. sticky tape.
• If a spillage does occur, blot any liquids immediately with a clean, dry absorbent cloth and allow to dry naturally.
• Clean periodically in situ using a professional cleaning company.
• For more stubborn stains a professional upholstery cleaner should be consulted.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
PRODUCT INFORMATION
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Carefully check that you have all the parts before beginning assembly.
• Keep fittings out of children’s reach and keep children well away from construction area.
• Care should be taken to avoid spilling anything on the upholstery. If a spillage occurs act promptly and soak up any
liquids by blotting with a clean absorbent cloth. Never rub to remove stains. Never use a wet cloth.
• A minimum of 2 persons is required to assemble this product.
• Avoid exposure to direct or prolonged periods of sunlight and position away from direct heat sources such as
radiators.
• Fabric content - 50% Cotton, 50% Polyester.
• Made in China.
• Regular cleaning is essential to avoid build up of these products on the surface.
• Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
CARE INSTRUCTIONS
• Hair products such as hairsprays, oils and gels may affect the finish. Avoid prolonged contact with such products.
ANTOINETTE STORAGE BED 781396
Page 1 of 5

1. Attach 2 x side rails 3 to headboard 1 using 4 x
bolts (A), 2 x dowel (E), 4 x half moon washers (F) and
4 x nuts (G). Tighten with Spanner (Q).
1. Attach 2 x side rails 3 to footboard 2 using 4 x bolts
(A), 2 x dowel (E), 4 x half moon washers (F) and 4 x
nuts (G). Tighten with Spanner (Q).
PARTS
FITTINGS
STEP ONE
Page 2 of 5

1. Attach central support rail 11 to headboard 1 and
footboard 2 with 4 x bolts (C), 4 x flat washers (H) and
4 x spring washers (L). Tighten with Allen key (P).
1. Attach drawer 2x support rails 4 to side rails 3 with
8 x bolts (B), 8 x flat washers (H) and 8 x spring
washers (L). Tighten with Allen key (P).
1. Insert slats 13 into end caps (O) and double end
caps (N) as shown.
2. Insert each end cap into corresponding holes in 2 x
side rails 3 and central support rail 11. Repeat
process for each slat.
NOTES:
* The curve of the slat must be facing upwards.
* Number of slats and caps vary dependant on size.
Quantities as shown in FITTINGS and PARTS
sections.
Note: Double 13 x Slats
King 14 x Slats
Super King 14 x Slats
2. Attach central support leg 12 to central support rail
11 using 2 x bolts (D), 2 x nuts (G) and 4 x flat
washers (M). Tighten with a crosshead screwdriver
and spanner (Q).
1. Attach drawer cross bar 5 to drawer support rails 4
with 2 x bolts (B), 2 x dowels (K), 2 x flat washers (H)
and 2 x spring washers (L). Tighten with Allen key (P).
STEP FOUR
STEP THREE
STEP TWO
Page 3 of 5

1. Carefully slide drawer bottoms 9 into each
previously assembled drawer frame.
2. Insert 2 x wooden dowels (K) into drawer strength
rail 10. Attach drawer strength rail 10 to drawer back
8. Repeat for second drawer frame.
1. Insert 4 x cam bolts (I) into drawer front 7 and
tighten with a screwdriver. Insert 2 x wooden dowels
(K) into drawer front 7.
2. Insert 2 x wooden dowels (K) into drawer strength
rail 10 and attach drawer front 7 to assembled drawer
frames.
3. Insert 4 x cam locks (J) into drawer sides 6 and
tighten with a screwdriver.
4. Repeat previous steps for the second drawer.
STEP SIX
STEP SEVEN
STEP FIVE
1. Insert 4 x cam bolts (I) into 2 x drawer sides 6 and
tighten with a screwdriver (not supplied).
2. Insert 2 x wooden dowels (K) into the 2 drawer
sides 6.
3. Attach drawer sides 6 to drawer back 8. Insert 4 x
cam locks (J) into drawer back 8 and tighten with a
screwdriver .
4. Repeat previous steps to assemble the second
drawer frame using the remaining drawer sides 6 and
drawer back 8.
I
I
Page 4 of 5

Insert the assembled drawers into the bed frame.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP TEN
STEP EIGHT
Page 5 of 5