Next HARTFORD LT 860134 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Made in China.
• A minimum of 2 persons is required to assemble this product.
• Do not rub or scrub the surface when cleaning.
• For general cleaning, periodically dust with a soft cloth.
PRODUCT INFORMATION
• Made from Pine with NC lacquer finish.
• Keep fittings out of children's reach and keep children well away from the construction area.
CARE INSTRUCTIONS
• Natural features ensure that each piece is individual. Every effort is made to ensure colour continuity between
pieces, however this is a natural product, slight colour variations and natural grain markings may occur.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Do not put hot dishes directly on the surfaces of the item.
860134 HARTFORD LT TV UNIT
Page 1 of 8

FITTINGS
PARTS
Page 2 of 8

1. Insert 10 x cambolts (A) into top panel (1).
4. Insert 4 x cambolts (A) into rail (3).
10. Insert 4 x dowels(E) into panel 2.
1. Attach panel(4) to panel (3)
2. Insert 4 x camlocks(B) into panel(4) and tighten
with a screwdriver.
1. Attach panel(9) & panel(10) to panel(5)
2. Insert 2 x camlocks(B) into panel(5) and tighten
with a screwdriver.
8. Insert 3 x cambolts (A) and 1 x dowel (E) into leg 7.
9. Insert 4 x cambolts (A) and 1 x dowel (E) into leg 9.
11. Insert 2 x dowels(E) into rail 5 and 2 x dowels(E)
into rail 4.
3. Insert 6 x cambolts (A) and 12 x dowels (E) into 2 x
panels (6).
5. Insert 3 x cambolts (A) and 1 x dowel (E) into leg
(8).
6. Insert 4 x cambolts (A) and 1 x dowel (E) into
leg (10).
7. Insert 1 x dowel (D) into rail 11 and 1 dowel (D) into
rail 12.
STEP ONE
STEP TWO
STEP THREE
2. Attach 1 x wall attachment strap (L) to the back of
the top panel with 1 x washer (M) and 1 x screw (N).
Page 3 of 8

1. Attach panel(8) to panel(6).
2. Insert 3 x camlocks(B) insert panel(6) and tighten
with a screwdriver.
1. Attach panel(2) to panel(6).
2. Insert 3 x camlocks(B) into panel(2) and tighten
with a screwdriver.
1. Attach panel(3),(4) to panel(8) and secured with 1x
screw(C )
STEP FOUR
STEP FIVE
STEP SIX
Page 4 of 8

1. Attach panel(6) to assembled unit.
2. Insert 3 x camlocks(B) into panel(2) and tighten
with a screwdriver.
1. Attach panel(7) to assembled unit.
2. Insert 3 x camlocks(B) to panel(6) and tighten with
a screwdriver.
3. Insert 1 x screw (C ) to panel 3 and tighten with a
screwdriver.
1. Attached panel(9),(10) to assemble unit.
2. Insert 6 x camlocks(B) 2 x panel(6) and tighten with
a screwdriver.
STEP SEVEN
STEP EIGHT
STEP NINE
Page 5 of 8

1. Secured panel(4) to panel(7) & panel(8) with 4 x
screws(C ) and tighten by a screwdriver
1. Attach rail(11) & rail(12) to assembled unit
2. Insert 4 x screws (H) into rails 11 & 12 and tighten
with a screwdriver
1. Turn the unit so that it is stood up.
2. Attach top panel (1) to the assembled unit.
3. Insert 10 x camlocks(B) into 2 x panel(6) and legs
(7),(8),(9) & (10), tighten with a screwdriver.
STEP TEN
STEP ELEVEN
STEP TWELVE
Page 6 of 8

1. Attach back panel(19) to the assembled unit with 14
x screws (K) and tighten with a screwdriver.
1. Insert 4 x cambolts(A) and 1 x cambolt(I) into
drawer front panel(13).
2. Attach panel(14),(15) & (18) to panel(13).
3. Insert 4 x camlock (b) to panel (14) & (15), tighten
with a screwdriver.
4. Insert 1 x camlock(J) into panel (18) and tighten
with a screwdriver.
5. Slide panel(17) into the grooves of panel(14),(15) &
(13)
6. Attach panel(16) to assembled unit and secured
with 6 x screws(H), tighten with a screwdriver.
7. Attach 2 x handles(F) to front panel(13) and secured
with 4 x screws (G) by a screwdriver.
1. Insert the drawer into the assembled unit.
2. Insert 2 dowels(D) into drawer sides to act as
drawer stops and prevent the drawer from falling out
by accident.
3. Move the item into position and attach the end of
the strap to the wall with the approciate screw,
washer and wall plug for your wall type.
STEP FOURTEEN
STEP FIFTEEN
STEP THIRTEEN
4. WARNING: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas pipes.
5. NOTE: Wall fixings are not included, please source
suitable fixings for your wall type. If in doubt, please
consult a qualified tradesman.
WALL
Page 7 of 8

Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 8 of 8