Next WESTCOTT BED User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• All assembly xings should always be tightened properly and periodically check all xings and tighten if necessary.
CARE INSTRUCTIONS
• Hair products such as hairsprays, oils and gels may aect the nish. Avoid prolonged contact with such products.
• Clean periodically in situ using a professional cleaning company.
• For more stubborn stains a professional upholstery cleaner should be consulted.
• Regular cleaning is essential to avoid build up of these products on the surface.
• Care should be taken to avoid spilling anything on the upholstery. If a spillage occurs act promptly and soak up any
liquids by blotting with a clean absorbent cloth. Never rub to remove stains. Never use a wet cloth.
• Avoid exposure to direct or prolonged periods of sunlight and position away from direct heat sources such as
radiators.
• If a spillage does occur, blot any liquids immediately with a clean, dry absorbent cloth and allow to dry naturally.
•
Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
•
Made in China.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Fabric content - 50% Cotton, 50% Polyester.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
PRODUCT INFORMATION
IMPORTANT
• We suggest you spend a short time reading through this leaet and then follow the simple step-by-step instructions.
• Carefully check that you have all the parts before beginning assembly.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• Keep ttings out of children’s reach and keep children well away from construction area.
WESTCOTT BED
Page 1 of 4

1. Screw 2 x legs 4 to headboard 1. Tighten with
hand.
2. Screw 2 x legs 4 to footboard 2. Tighten with hand.
FITTINGS
PARTS
STEP ONE
Page 2 of 4

1. Attach 2 x side rails 3 to headboard 1 using 4 x
bolts (A), 2 x dowel (D), 4 x half moon washers (E)
and 4 x nuts (F). Tighten with Spanner (M).
1. Attach 2 x side rails 3 to footboard 2 using 4 x bolts
(A), 2 x dowel (D), 4 x half moon washers (E) and 4 x
nuts (F). Tighten with Spanner (M).
1. Attach central support rail 5 to headboard 1 and
footboard 2 with 4 x bolts (B), 4 x flat washers (G)
and 4 x spring washers (H). Tighten with Allen key
(L).
2. Attach central support leg 6 to central support rail
5 using 2 x bolts (C), 2 x nuts (F) and 4 x flat washers
(I). Tighten with a crosshead screwdriver (not
supplied) and spanner (M).
STEP FOUR
STEP THREE
STEP TWO
Page 3 of 4

1. Insert slats 7 into end caps (K) and double end
caps (J) as shown.
2. Insert each end cap into corresponding holes in 2 x
side rails 3 and central support rail 5. Repeat process
for each slat.
NOTES:
* The curve of the slat must be facing upwards.
* Number of slats and caps vary dependant on size.
Quantities as shown in FITTINGS and PARTS
sections.
Note: Double 13 x Slats
King 14 x Slats
Super King 14 x Slats
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP THIRTEEN
STEP FIVE
Page 4 of 4