Next SOPHIE CABIN STATION 889951 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
FITTINGS
• Made from MDF with a painted finish.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• Not suitable for use in bathrooms.
CARE INSTRUCTIONS
• Made in China.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• For general cleaning, periodically dust with a soft cloth.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Keep fittings out of children's reach and keep children well away from the construction area.
PRODUCT INFORMATION
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Carefully check that you have all parts before beginning assembly.
889951 SOPHIE CABIN BED-CHEST
Page 1 of 6

1. Insert 2 x wooden dowels (C) into middle divider
panel 3.
2. Attach 2 x supporting rails 7 to middle divider panel 3
with 2 x screws (H) and tighten.
STEP TWO
1. Insert 4 x cambolts (A) and 4 x wooden dowels (C)
into side panel 2-R.
2. Attach supporting rail 6, 2 x supporting rails 7 and
back supporting rail 8 to side panel 2-R.
3. Insert 4 x camlocks (B) into supporting rail 6, 2 x
supporting rails 7 and back supporting rail 8. Ensure the
arrow indicator is pointing towards the panel edge
before tightening with a screwdriver.
STEP ONE
PARTS
(3) Middle Divider
Panel x 1
Page 2 of 6

STEP THREE
1. Insert 4 x cambolts (A) and 4 x wooden dowels (C)
into side panel 2-L.
2. Attach side panel 2-L to the assembled unit.
3. Insert 4 x camlocks (B) into supporting rail 6, 2 x
supporting rails 7 and back supporting rail 8. Ensure the
arrow indicator is pointing towards the panel edge
before tightening with a screwdriver.
STEP FOUR
1. Insert 4 x wooden dowels (C) into bottom frame 9.
2. Attach bottom frame 9 to the assembled unit with 4 x
screws (H) and tighten .
STEP FIVE
1. Insert 6 x cambolts (A) and 6 x wooden dowels (C)
into top panel 1.
2. Attach top panel 1 to the assembled unit.
3. Insert 6 x camlocks (B) into side panels 2 (both L&R)
and middle divider panel 3. Ensure the arrow indicator is
pointing towards the panel edge before tightening with
a screwdriver.
Page 3 of 6

STEP SIX
1. Attach back panel 4 and back panel 5 to the
assembled unit with 20 x screws (D) and tighten.
STEP SEVEN
1. Attach drawer back panel 16 to drawer side panels 12
(both L&R) with 4 x screws (E) and tighten.
2. Insert drawer bottom panel 17 into the grooves of
drawer side panels 12 (both L&R).
3. Attach drawer front panel 15 to the assembled unit
with 4 x screws (E) and tighten.
4. Attach 1 x handle (G) to drawer front panel 15 with 1 x
bolts (F) and tighten.
5. Repeat step 1 to 4 for another one small drawer.
STEP EIGHT
1. Insert 1 x cambolt (A) into drawer front panel 10.
2. Attach 1 x support slat 14 to drawer front panel 10.
3. Insert 1 x camlock (J) into support slat 14. Ensure the
arrow indicator is pointing towards the panel edge
before tightening with a screwdriver.
4. Attach drawer side panels 12 (both L&R) to drawer
front panel 10 with 4 x screws (E) and tighten.
5. Insert drawer bottom panel 13 into the grooves of
drawer side panels 12 (both L&R).
6. Attach drawer back panel 11 to the assembled unit
with 6 x screws (E) and tighten.
7. Repeat step 1 to 6 for another 1 drawer.
Page 4 of 6

STEP NINE
Insert drawers into the unit.
STEP TEN
Position as shown
Page 5 of 6

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
PACKAGING LAYOUT
Page 6 of 6