Next PARIS STORAGE BED SINGLE User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Keep fittings out of children’s reach and keep children well away from construction area.
• Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
• Made in China.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
PRODUCT INFORMATION
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Carefully check that you have all the parts before beginning assembly.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• Regular cleaning is essential to avoid build up of these products on the surface.
• Care should be taken to avoid spilling anything on the upholstery. If a spillage occurs act promptly and soak up any
liquids by blotting with a clean absorbent cloth. Never rub to remove stains. Never use a wet cloth.
• Avoid exposure to direct or prolonged periods of sunlight and position away from direct heat sources such as
radiators.
• If a spillage does occur, blot any liquids immediately with a clean, dry absorbent cloth and allow to dry naturally.
CARE INSTRUCTIONS
• Hair products such as hairsprays, oils and gels may affect the finish. Avoid prolonged contact with such products.
• Clean periodically in situ using a professional cleaning company.
• For more stubborn stains a professional upholstery cleaner should be consulted.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
PARIS BED
Page 1 of 4

FITTINGS
PARTS
25mm
40mm
35mm
Page 2 of 4

1. Screw 2 x legs 4 to headboard 1 using 2 x bolts (B),
2 x flat washers (D) and 2 x spring washers (F) x 2.
Tighten with Allen key (J).
1. Attach 2 x side rails 3 to headboard 1 and footboard
2 using 8 x bolts (A), 8 x flat washers (D) and 8 x
spring washers (F). Tighten with Allen key (J).
1. Screw 2 x legs 5 to footboard 2 and 2 x side rails 3
using 4 x bolts (B), 4 x flat washers (D) and 4 x spring
washers (F). Tighten with Allen key (J).
STEP ONE
STEP THREE
STEP TWO
Page 3 of 4

1. Attach central support rail 6 to headboard 1 and
footboard 2 with 8 x bolts (A), 8 x flat washers (D) and
8 x spring washers (F).
2. Attach central support leg 7 to central support rail 6
using 2 x bolts (C), 2 x nuts (G) and 4 x flat washers
(E). Tighten with a crosshead screwdriver and
spanner (K).
1. Insert slats 8 into end caps (I) and double end caps
(H) as shown.
2. Insert each end cap into corresponding holes in 2 x
side rails 3 and central support rail 6. Repeat process
for each slat.
NOTES:
* The curve of the slat must be facing upwards.
* Number of slats and caps vary dependant on size.
Quantities as shown in FITTINGS and PARTS
sections.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP FIVE
STEP FOUR
STEP SIX
C
E
E
G
Page 4 of 4