Nibe F1145-5 User guide

Installer manual
LEK
NIBE F1145
Ground source heat pump
IHB GB 1643-2
331509

Quick guide
Navigation
Ok button (confirm/select)
Back button (back/undo/exit)
Control knob (move/increase/reduce)
A detailed explanation of the button functions can be found on page 38.
How to scroll through menus and make different settings is described on page 41.
Set the indoor climate
2X
The mode for setting the indoor temperature is accessed by pressing the OK button twice, when in the start mode
in the main menu.
Increase hot water volume
2X
1X
To temporarily increase the amount of hot water (if a hot water heater is installed to your F1145), first turn the
control knob to mark menu 2 (water droplet) and then press the OK button twice.

Table of Contents
41 Important information
4Safety information
62 Delivery and handling
6Transport
6Assembly
7Supplied components
7Removing the covers
83 The heat pump design
8General
10Distribution boxes
12Cooling section
144 Pipe connections
14General
15Dimensions and pipe connections
15Brine side
16Heating medium side
16Water heater
17Docking alternatives
195 Electrical connections
19General
21Connections
23Settings
25Optional connections
29Connecting accessories
316 Commissioning and adjusting
31Preparations
31Filling and venting
32Start guide
33Post adjustment and venting
35Setting the cooling/heating curve
387 Control - Introduction
38Display unit
39Menu system
438 Control - Menus
43Menu 1 - INDOOR CLIMATE
43Menu 2 - HOT WATER
43Menu 3 - INFO
44Menu 4 - HEAT PUMP
45Menu 5 - SERVICE
569 Service
56Service actions
6210 Disturbances in comfort
62Info menu
62Manage alarm
62Troubleshooting
6511 Accessories
6712 Technical data
67Dimensions and setting-out coordinates
68Technical specifications
74Energy labelling
95Item register
99Contact information
3Table of Contents |NIBE F1145

Safety information
This manual describes installation and service procedures
for implementation by specialists.
This appliance can be used by children
aged from 8 years and above and per-
sons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and under-
stand the hazards involved. Children shall
not play with the appliance. Cleaning
and user maintenance shall not be made
by children without supervision.
Rights to make any design or technical
modifications are reserved.
©NIBE 2016.
Symbols
NOTE
This symbol indicates danger to machine or
person.
Caution
This symbol indicates important information
about what you should observe when maintain-
ing your installation.
TIP
This symbol indicates tips on how to facilitate
using the product.
Marking
The CE marking means that NIBE ensures that the
product meets all regulations that are placed on it based
on relevant EU directives. The CE mark is obligatory for
most products sold in the EU, regardless where they are
made.
Serial number
The serial number can be found at the bottom right of
the front cover and in the info menu (menu 3.1) and on
the type plate (PF1).
Serial number
Caution
You need the product's ((14 digit) serial number
for servicing and support.
Recovery
Leave the disposal of the packaging to the in-
staller who installed the product or to special
waste stations.
Do not dispose of used products with normal
household waste. It must be disposed of at a
special waste station or dealer who provides this type of
service.
Improper disposal of the product by the user results in
administrative penalties in accordance with current legis-
lation.
Environmental information
This unit contains a fluorinated greenhouse gas that is
covered by the Kyoto agreement.
F-Gas Regulation (EU) No. 517/2014
The equipment contains R407C, a fluorinated green-
house gas with a GWP value (Global Warming Potential)
of 1,774. Do not release R407C into the atmosphere.
Country specific information
Installer manual
This installer manual must be left with the customer.
NIBE F1145Chapter 1 | Important information4
1 Important information

Inspection of the installation
Current regulations require the heating installation to be inspected before it is commissioned. The inspection must
be carried out by a suitably qualified person. In addition, fill in the page for the installation data in the User Manual.
DateSignatureNotesDescription
✔
Brine (page 15)
System flushed
System vented
Antifreeze
Level/Expansion vessel
Particle filter
Safety valve
Shut off valves
Circulation pump setting
Heating medium (page 16)
System flushed
System vented
Expansion vessel
Particle filter
Safety valve
Shut off valves
Circulation pump setting
Electricity (page 19)
Connections
Main voltage
Phase voltage
Fuses heat pump
Fuses property
Outside sensor
Room sensor
Current sensor
Safety breaker
Earth circuit-breaker
Setting of emergency mode thermostat
5Chapter 1 | Important informationNIBE F1145

Transport
F1145 should be transported and stored vertically in a
dry place. When being moved into a building, F1145
may be leant back 45 °.
Caution
The product can be tail heavy.
If the cooling module is pulled out and transported up-
right, F1145 can be transported on its back.
Remove the outer panels in order to protect them when
moving in confined spaces inside buildings.
R
0
R
0
Extracting the cooling module
To simplify transport and service, the heat pump can be
separated by pulling the cooling module out from the
cabinet.
See page 58 for instructions about the separation.
Assembly
■Position F1145 on a fixed foundation that can take the
weight of the heat pump. Use the product's adjustable
feet to obtain a horizontal and stable set-up.
30 - 50 mm
30 - 50 mm
15 - 40 mm
20-55 mm
■Because water comes from F1145, the area where the
heating pump is located must be equipped with floor
drainage.
■Install with its back to an outside wall, ideally in a room
where noise does not matter, in order to eliminate
noise problems. If this is not possible, avoid placing it
against a wall behind a bedroom or other room where
noise may be a problem.
■Wherever the unit is located, walls to sound sensitive
rooms should be fitted with sound insulation.
■Route pipes so they are not fixed to an internal wall
that backs on to a bedroom or living room.
Installation area
Leave a free space of 800 mm in front of the product.
Approx. 50 mm free space is required on each side, to
remove the side panels (see image). The panels do not
need to be removed during service. All service on F1145
can be carried out from the front. Leave space between
the heat pump and the wall behind (and any routing of
supply cables and pipes) to reduce the risk of any vibra-
tion being propagated.
(50) (50)
800
*
*
* A normal installation needs 300 – 400 mm (any side) for connec-
tion equipment, i.e. level vessel, valves and electrical equipment.
NIBE F1145Chapter 2 | Delivery and handling6
2 Delivery and handling

Supplied components
LEK
LEK
LEK
Room sensor
1 x
Current sensor
3 x
(not 1x230V)
Outside sensor
1 x
LEK
LEK
O-rings
8 x
Safety valve
0.3 MPa (3 bar)
1 x
Level vessel
1 x
WILO
LEK
LEK
WILO
WILO
2,5(22)
H- 50 - 2,5
TUV-SV-97-525
WILO
LEK
LEK
WILO
WILO
2,5(22)
H- 50 - 2,5
TUV-SV-97-525
Compression ring couplings
F1145 5-10 kW
2 x (ø28 x G25)
3 x (ø22 x G20)
F1145 12-15 kW
5 x (ø28 x G25)
F1145 17 kW
3 x (ø28 x G25)
2 x (ø35 x G32)
Particle filter
6-10 kW
1 x G1, 1 x G3/4
12-17 kW
1 x G1, 1 x G1 1/4
LEK
Insulation tape
1 x
Tubes for sensors
3 x
Temperature
sensor
3 x
LEK
Aluminium tape
1 x
Location
The kit of supplied items is placed in packaging on top
of the heat pump.
Removing the covers
Front cover
1
2
LEK
LEK
LEK
LEK
LEK
1. Remove the screws from the lower edge of the front
panel.
2. Lift the panel out at the bottom edge and up.
Side covers
LEK
LEK
LEK
The side covers can be removed to facilitate the installa-
tion.
1. Remove the screws from the upper and lower edges.
2. Twist the cover slightly outward.
3. Move the hatch outwards and backwards.
4. Assembly takes place in the reverse order.
7Chapter 2 | Delivery and handlingNIBE F1145

General
F1145
UB1
EB1
QM34
QM31
UB3
AA4
AA4-XJ3
UB2
QM32
AA4-XJ4
SF1
QM33
XL1
XL6 XL7
XL2XL9
QN10
PF1
PF2
BT2
W130
View from behind
BF1
NIBE F1145Chapter 3 | The heat pump design8
3 The heat pump design

Pipe connections
Connection, heating medium flowXL1
Connection, heating medium returnXL2
Connection, brine inXL6
Connection, brine outXL7
Connection, hot water heaterXL9
HVAC components
Shut-off valve, heating medium flowQM31
Shut off valve, heating medium returnQM32
Shut off valve, brine outQM33
Shut-off valve, brine inQM34
Shuttle valve, climate system/water heaterQN10
Sensors etc.
Flow meter**BF1
Outdoor temperature sensor*BT1
Temperature sensors, heating medium flowBT2
**Only heat pumps with energy meter
* Not illustrated
Electrical components
Display unitAA4
AA4-XJ3 USB socket
AA4-XJ4 Service outlet (No function)
Immersion heaterEB1
SwitchSF1
Network cable for NIBE UplinkW130
Miscellaneous
Rating platePF1
Type plate, cooling sectionPF2
Cable gland, incoming electricityUB1
Cable glandUB2
Cable gland, rear side, sensorUB3
Designations in component locations according to
standard IEC 81346-1 and 81346-2.
9Chapter 3 | The heat pump designNIBE F1145

Distribution boxes
F1145
FB1
FD1
AA1
FA1
AA3
AA2
Electrical components
Immersion heater cardAA1
Base cardAA2
Input circuit boardAA3
Miniature circuit-breakerFA1
Motor cut-out*FB1
Temperature limiter/Emergency mode thermostatFD1
* 1x230 V, 3x230 V 6-10 kW, 3x400V 5 kW has auxiliary switch for
motor cut-out.
Designations in component locations according to
standard IEC 81346-1 and 81346-2.
NIBE F1145Chapter 3 | The heat pump design10