Nice TT6 Technical specifications

TT6
EN - Instructions and warnings for
installation and use
IT - Istruzioni ed avvertenze per
l’installazione e l’uso
FR - Instructions et avertissements
pour l’installation et l’utilisation
ES - Instrucciones y advertencias
para la instalación y el uso
DE - Installierungs-und Gebrauchsan-
leitungen und Hinweise
PL - Instrukcje i ostrzeżenia do
instalacji i użytkowania
NL - Aanwijzingen en aanbevelingen
voor installatie en gebruik
Control unit for tubular motors
RS232 interface

22

English - 1
EN
Original instructions
ENGLISH
1 –WARNINGS
•Caution! It is important to observe these instruc-
tions to guarantee the safety of persons.
• Caution! Important safety instructions: store these
instructions in a safe place.
• Caution! All product installation, connection, pro-
gramming and maintenance operations must be
performed exclusively by a qualified and skilled
technician!
• Do not effect modifications to any part of the product
other than those specified in this manual. Unautho-
rised operations can lead to hazards and cause mal-
functions. The manufacturer declines all liability for dam-
ages caused by makeshift modifications to the product.
• Important! - Do not use substances containing alcohol,
benzene, diluents or other flammable substances. Use of
such substances could damage the product.
• Store this manual with care in a safe place to facilitate any
future product maintenance and programming opera-
tions.
• The product packaging material must be disposed of in
full observance of current local regulations governing
waste disposal.
• Use a soft and slightly damp (not wet!) cloth for cleaning
the product’s surfaces.
2 –PRODUCT DESCRIPTION AND INTENDED
USE
The TT6 control unit is designed for use in automation sys-
tems applied to awnings, shutters, skylights, vertical cur-
tains, blinds and for controlling video projection screens.
Any other use is to be considered improper and is
strictly prohibited! The manufacturer declines all liabil-
ity for damage resulting from improper use of the
product and other than as specified in this manual.
The product comprises the following:
- Output for controlling a wire technology motors (for
example, One-Max, To-max or NeoM); the output can be
activated directly through the two buttons: Pup () and
Pdown ();
- TTBUS interface for controlling Nice motors with bus sys-
tem.
- RS232 interface for connection to PC.
- Activation input (Trigger) for activating or deactivating a
sequence of motors (near the up or down trigger).
The radio interface expands the product’s remote control
range through the Nice radio technology.
3 –INSTALLATION
01. Remove the top cover of the control unit (Fig. 1).
02. In the zones marked accordingly, drill the holes for
routing the cables and for fixing the control unit to the
wall. Caution! – Take suitable precautions to
guarantee the IP protection rating required for
the type of installation. In particular, apply cable
clamps (not supplied) to protect the power

2- English
EN
cables and control cables against possible trac-
tion or torsion.
03. Fix the control unit housing to the wall (Fig. 2).
Caution! – The receiver must be positioned so that
the cables enter the housing exclusively from the
bottom.
1
2
4 –ELECTRICAL CONNECTIONS
Warnings
• When connecting the aerial provided, leave the wire at the
supplied length and lay it straight so as to avoid excessive
bending.
• If the control unit is not in an optimal position and the
radio signal is weak, improve reception by replacing the
aerial supplied with an external version (model ABF or
ABFKIT). The new aerial must be positioned as high as
possible and above any metal or reinforced concrete
structures present in the area.
4.1 –Inputs (Fig. 3 and Table 1)
•LElectrical phase
•NNeutral
•TTBUS: (TTBUS, GND)
•RS232 with dedicated protocol
•5-24 VDC trigger with programmable On and Off events
– 30+30 programmable events
– Event: address, command
•Two inputs for open-close commands for 85-265 VAC
50/60 Hz mechanical motor
– Open-STOP, Close-STOP operation
– “ON-PRESS” activation
4.2 –Outputs
• Power relay output for controlling a mechanical/electronic
motor with programmable manoeuvres (up and down), acti-
vated through two button inputs Pup () and Pdown () of
the 12 V Trigger or via Transmitter.

English - 3
EN
TABLE 1
Wiring diagram
1Electrical phase
2Neutral
3Ground
4Up button linked to the connectable mechanical
motor
5Down button linked to the connectable mechanical
motor
6Mechanical motor ground
7Mechanical motor down phase
8Mechanical motor common contact
9Mechanical motor up phase
10 TX signal of the RS232 interface
11 RX signal of the RS232 interface
12 Common contact (GND) of the RS 232 serial signal
13 Signal of the motor with TTBUS (White wire)
14 Common contact of the motor with TTBUS (White/
Black wire)
15 External activation trigger signal (positive pole input)
16 External activation trigger common contact (nega-
tive pole input)
ANT Aerial input
– The activation timer can be adjusted to between 1 sec.
and 240 sec. through the serial port with an internal com-
mand.
– The default address of the motor connected to the control
unit is 1.
Refer to Table 2 to check the LEDs present.
16
P
POWER SUPPLY 100 - 240 V 50 - 60 Hz
TTBUS
TRIGGER 12 V
AERIAL
P
SG
DL7 RL1 PP
DL8 RL2
DL5 P DL4 TRG
DL6 P
DL3 DL2 DL1
23
RS232
5
SG
3

4- English
EN
TABLE 2 -Signalling LEDs
Led Description
DL1 Red LED Power supply indicator.
DL2 Yellow LED If on, transmitter memorisation is
active.
DL3 Green LED Signals.
DL4 12 V signal trigger indicator.
DL5, DL6 Red LED External buttons open-close in-
dicator for mechanical motor.
DL7, DL8 Red LED Open-close relays activation.
3- Close
4- Stop
5- Close after 10 sec.
6- Open after 10 sec.
7- Close after 20 sec.
8- Open after 20 sec.
9- Hold-to-run close
10 - Hold-to-run open
11 - Activate the list of programmed command linked to the
12v trigger Up scenario
12 - Activate the list of programmed command linked to the
12v trigger DOWN scenario
13 - Forward radio transmission on RS232 serial
5.1 –Memorising a transmitter in “Mode I”
01. Press and hold P1 on the control unit until the green
LED DL1 lights up (after approx. 4 seconds) then
release; the yellow LED DL2 will also turn on.
02. Within 10 seconds, press and hold any key of the transmit-
ter to be memorised, until the green LED DL1 on the con-
trol unit emits the first of 3 flashes to confirm memorisation.
Following these flashes, to memorise another transmitter in
“Mode I”, press any key on the new transmitter within 10
seconds. Lastly, wait until yellow LED DL2 turns off.
Caution! – When attempting to memorise a transmitter that
is already stored, the green LED DL1 will signal this by flash-
ing once.
5.2 –Memorising a transmitter in “Mode II”
01. From the “Mode II” list, select the function to be pro-
grammed (e.g. “Function 8”).
5 –PROGRAMMING
The control unit can memorise transmitters in two modes,
namely Mode I and Mode II:
Mode I
– Button 1controls the Opening for the pre-set manoeuvre
duration (Tm) (maximum 240 sec.).
– Button 2controls the Stop.
– Button 3controls the Closing for the pre-set manoeuvre
duration (Tm) (maximum 240 sec.).
– Button 4controls the Stop, once again.
Mode II
The transmitter button can be linked to one of the following
functions:
1- Step-by-step
2 - Open

English - 5
EN
02. On the receiver, press P1 the same number of times as
the number identifying the selected function (in our
example, 8 times). On completion, the green LED DL1
emits a number of short flashes corresponding to the
number of times the key was pressed (in our example, 8
short flashes);
03. Within 10 seconds, press and hold the transmitter key
to be memorised, until the green LED DL1 on the
receiver emits the first of 3 flashes to confirm memorisa-
tion. After these flashes, to store a new key (even on
another transmitter) with the same function, press this
new key within 10 seconds (yellow LED DL2 on).
04. When attempting to memorise a transmitter that is
already stored, the green LED DL1 will signal this by
flashing once.
5.3 –Deleting all memorised transmitters
01. Press and hold P1 for long on the control unit and check
the sequence of statuses of the green LED DL1.
02. After approximately 4 seconds, it turns on…
03. After approximately 4 seconds, it turns off…
04. After approximately 4 seconds, it starts flashing...
At this stage:
05. To delete all memorised transmitters, release the receiv-
er key on precisely the third flash of the green LED
DL1.
06. To delete the entire memory (including transmitter con-
figurations and encoding family), release the key on pre-
cisely the fifth flash of the green LED DL1.
07. To delete a single transmitter, release the key on pre-
cisely the seventh flash then press a key (*) on the trans-
mitter to be deleted from the memory within ten sec-
onds (yellow LED DL2 on); the green LED DL1 will emit
5 rapid flashes upon deletion.
08. Repeat the operation within ten seconds (yellow LED
DL2 on) to delete another transmitter.
(*) Note – If the transmitter is memorised in “Mode I”, press any key;
if the transmitter is memorised in “Mode II”, press the memorised
key; if multiple keys are memorised, repeat the procedure for each
memorised key.
5.4 –Communication protocol
CMD [XX] [YY] [AA] [Optional data field] [Carriage Return]
Note – The fields are one space apart.
[CMD] This is a 3-character field. Conventional-
ly, commands sent to the T4/TTBUS
bus will always be in “CMD” form.
[XX] [YY] These are 2-character fields indicating
the device Address and Node, respec-
tively. These two fields are mandatory
and must be entered in hexadecimal
form.
[AA] Field indicating the command to be
sent. It is 2-characters long and is
mandatory. It represents the ID of the
command to be sent according to the
previously-listed commands list (for
example: 04 open; 05 close; etc.).
[Data field] Variable-length optional field. Its size
depends on the type of command

6- English
EN
60 Delete transmitter
65 Delete all memorised transmitters
66 Delete motor parameters
20 Memorise the motor upper limit switch in current
position
21 Memorise the motor lower limit switch in current
position
22 Memorise partial position 1 in current position
23 Memorise partial position 2 in current position
24 Memorise partial position 3 in current position
25 Memorise partial position 4 in current position
26 Memorise partial position 5 in current position
27 Memorise partial position 6 in current position
30 Delete upper limit switch setting
31 Delete lower limit switch setting
32 Delete partial position 1
33 Delete partial position 2
34 Delete partial position 3
35 Delete partial position 4
36 Delete partial position 5
37 Delete partial position 6
05 Up
12 Move a little step up
03 STOP
sent to the device: some commands
do not require data (for example, the
Open command), while others do (for
example, the Open percentage com-
mand).
[Carriage Return] Decimal code 13, hexadecimal code
0D; it must always be present and each
string sent must end with this charac-
ter.
For each command sent, the interface must provide a
response that simply indicates the command reception
(this, however, does not imply that the command has been
executed by the automation). It is a notification that will
currently have a very simple construction, such as the fol-
lowing:
RSP [XX] [YY] [ZZ] [Optional data field] [Carriage Return]
5.5 –Commands list
CMD Description
45 READ PERCENTAGE POSITION 0 - 255
Low limit switch 255 = High limit switch
04 Down
40 OPEN percentage command percentage 0 - 255
0 = Low limit switch 255 = High limit switch
50 Read memorised transmitters
51 Memorise transmitter

Response
5.5.2 –STOP command
Stops the motor.
Structure
The data field is empty.
Example
Response
English - 7
EN
13 Move a little step down
06 Move to partial position 1
07 Move to partial position 2
08 Move to partial position 3
09 Move to partial position 4
10 Move to partial position 5
11 Move to partial position 6
Note – The available commands must also be available for the
motor.
5.5.1 –Move to partial position 1, 2, 3, 4, 5, 6
command
Moves the motor to the set position after the partial position
has been assigned.
Structure
The data field is empty.
Example
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD IND 04 06 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD 01 04 06 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
RISP 01 04 06 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD 01 04 06 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
RISP 01 04 06 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD IND 04 03 – –

8- English
EN
5.5.3 –UP command
Commands the motor’s “up” movement until the set limit
switch.
Structure
The data field is empty.
Example
Response
5.5.4 –DOWN command
Commands the motor’s “down” movement until the set limit
switch.
Structure
The data field is empty.
Example
Response
5.5.5 –Move a little step down
Sends a “down” command that it make the smallest move-
ment that the motor can do. Use to set the right position
before setting the limits switch or the partial positions.
Caution: the up and down directions are correctly
assigned after setting the relevant limit switches.
Structure
The data field is empty.
Example
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD 01 04 05 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
RISP 01 04 05 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD IND 04 04 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD 01 04 04 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
RISP 01 04 04 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD 01 04 13 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD IND 04 13 – –
Start TT ADR
[XX]
TT ENDPOINT
[YY]
Command
[AA]
Data CR
CMD IND 04 05 – –