Niche MIA N2020LNTBK User manual

Find your niche
VERSATILE AND MODERN
MIA RECLINING CHAIR
N2020LNTBK & N2050LNTBK
BEFORE YOU ASSEMBLE:
• Place all parts on a clean, smooth surface to avoid scratching the parts
• Check to be sure you have all parts and hardware
• Remove all wrapping materials, including any staples & packing straps
• Keep all hardware, small parts and packaging out of reach of children
ASSEMBLY INSTRUCTIONS
IN THE BOX:
A: Wood Frame (2) B: Stringer (2)
D: Seat Frame (1)
I: Seat
Cushion
(1)
C: Back Frame (1)
E: Medium Bolt (4) F: Small Bolt (2)
G: Long Bolt with Insert (4)
H. Threaded
Flange (2) J. Allen Wrench
(1)
K. Headrest

STEP 1
STEP 2
Aach Back Frame (C) to Seat Frame (D) using Small Bolts (F)
and Threaded Flanges (H). Insert Small Screws (F) in the front
of the chair, and Threaded Flanges (H) in the back. Tighten
bolts with Allen Wrench (J). (See Figure 2.)
Aach assembled seat to completed fram with Medium Bolts
(E). Insert Bolts from outside of Frame (A) and into Seat using
Allen Wrench (J). Aer seat and frame are aached, completely
ghten down all bolts using Allen Wrench (J).
Next, place Seat Cushion (I) onto assembled frame and aach
with velcro strips on back and seat. Then, aach Headrest (K)
by wrapping straps around the assembled chair. (See Figure 3.)
D
EK
EI
A
E
E
F
F
F
H
H
H
C
STEP 3
Aach Stringers (B) to Wood Frames (A). Remove Inserts from Large Bolts (G) and place Inserts into pre-drilled holes on Stringers (B)
(See Figure 1.) Insert Large bolts (G) from outside of Wood Frames (A) and connect to Inserts using Allen Wrench (H). Please Note: Do not
completely ghten bolts yet.
A
B
A
A
B
BGG
G
G
Figure 1
Find your niche
VERSATILE AND MODERN
MIA RECLINING CHAIR
N2020LNTBK & N2050LNTBK
ASSEMBLY INSTRUCTIONS
Figure 2
Figure 3

IN THE BOX
STEP 1
N2050LNTBK OTTOMAN
Find your niche
VERSATILE AND MODERN
MIA RECLINING CHAIR
N2020LNTBK & N2050LNTBK
ASSEMBLY INSTRUCTIONS
L: Cushion (1)
N: Wood Frame (2)
M: Stringers (2)
O: Long Bolt with
Inserts (4)
P: Medium Bolts (4)
Aach Stringers (M) to Wood Frames (N). Remove Inserts from Large Bolts
(O) and place Inserts into pre-drilled holes on Stringers (M) (See Figure 4.)
Insert Large bolts (O) from outside of Wood Frames (N) and connect to Inserts
using Allen Wrench (J). Please Note: Do not completely ghten bolts yet.
M
NP
P
L
NM
M
M
O
O
O
O
O
Figure 4
Aach Cushion (L) to assembled frame. Place cushion
upside down and set frame on top. Line up holes on
Stringers (M) with holes on Cushion. Insert Medium
Bolts (P) into pre-drilled holes and aach with Allen
Wrench (J).
Finally, completely ghten all bolts with Allen Wrench (J).
Note: The larger holes on
the sides of the Stringers (M)
should be facing downward,
and the holes for the Inserts
should be facing inward.
STEP 2