Nienkamper CERN BOOKCASE CREDENZA User manual

Customer Support: 1.800.668.9318
Email: [e-mail]
Web: www.nienkamper.com
Page 1 of 4
On a protective surface, lay gables and top with back edge on floor. Screw mini fix pin into gables. Insert wood dowels into remaining
holes. Install mini fix cam into top with phillips drive facing out and arrow facing though hole. Align all holes in top with dowels / pins
and gently push together. Be sure to align lighting cable with groove in gable so damage does not occur when tightening. With a #3
phillips screwdriver, turn mini fix cam to lock assembly. Repeat both sides.
Install all shelf mounting blocks by screwing 1/4”-20 x 1 5/8” socket head cap screw through block and into pre-installed inserts in gable.
Repeat step for all mounting blocks.
top
mini fix
cam
mini fix screw
gable
light power cable
dowel
CERN BOOKCASE CREDENZA
INSTALLATION GUIDE
4mm Hex Key
5mm Hex Key
1/8” Hex Key
#2 Phillips Screwdriver / Bit
#3 Phillips Screwdriver/ Bit
Clamp
Mallet
Hammer
#6 x 5/8”
Pan Head
Wood Screw
Wood Dowel
Modeze
Screw
1/4”-20 x
9/16” Joiner
1/4”-20 x 7/8”
Set Screw
1/4”-20 x 7/8”
Joiner Bolt
HARDWARE:TOOLS REQUIRED:
SUGGESTED MINIMUM CREW: 2-3
APPROXIMATE INSTALL TIME: 2 Hrs
1/4”-20 x 1
1/4” Joiner
1/4”-20
Joiner nut
Mini-Fix
Screw,
Cam &
#6 x 5/8”
Pan Head
Wood Screw
Shelf
Mounting
Block
Wire
Cover
Wire
Manager
1/4”-20 x 1
5/8” Socket
Head Screw

Customer Support: 1.800.668.9318
Email: [e-mail]
Web: www.nienkamper.com
Page 2 of 4
Very carefully align machined opening in rear of shelf with the mounted shelf blocks on both gables and lower into place. Gables can
be spread slightly to allow more room to slip shelves into place. Please take time and care with this step. Long shelves require extra
care as to not scratch the gable finish. Once shelves are in place on the blocks, secure each side with 1/4”-20 x 7/8” set screws.
Rotate unit into upright position. Install the case feet with 1/4”-20 x 1” flat head machine screws (2 screw into bottom of
gable & 2 using the through holes and joiner nut. Outside feet angle to outer corners
and center feet are straight. Note: it is normal for the foot plate to hang out past the
gable. This allows bookcase component to be supported. When installing center feet,
remove file drawer if unit is equipped.
Rotate lower case into upright position on legs.
To avoid any damage to light cables installed in shelves, it is suggested to drape them over
the shelves to keep them out of the way. Carefully lift the bookcase component into place,
resting on foot plates. Align the through holes in lower case with pre-installed inserts on
bookcase gables. Secure with 1/4”-20 x 1 1/4” joiner bolts.
set screw

Customer Support: 1.800.668.9318
Email: [e-mail]
Web: www.nienkamper.com
Page 3 of 4
Feed all light cables from shelf through notches in wire guide and down rebated area in gable. Cables run down rebate and turn to
exit in lower case cavity. If this is dicult, slightly loosen the joiner bolts that hold gables. Repeat this for all cables. If your assembly
includes a shelf mounted switch, feed plug and cable into hole in underside of shelf until switch seats in place. Feed cables in the
same way as lighting cables. Push wire cover into place for a friction fit. Repeat for opposite side.
*Note: to tighten wire guide fit, tape can be placed on either leg of leg for snug the fit.*
!
Align the shelf lip extrusion with shelf, hook top edge and tilt into place.
Exercise caution not to have any fingers near the snap connection at bottom.
Be sure that cables exiting the shelf are not going to interfere with fit.
To install the vertical shelf supports, start with the
bottom support. Align the clip that is installed in
the bottom of the support with the pre-installed
modeze screw located on the top of the lower
case. Tilt the support sideways slightly and
position vertically once engaged with screw.
Slide back to lock into position. Using #8 x 1
1/2” flat head wood screws lock shelf to next
shelf above. Install modeze screw in pre-drilled
pilot hole on top surface of next aluminum shelf.
Repeat for all supports.
rebated
gable
light cable
wire cover
light cable
possible pinch point
shelf support
modeze screw

Customer Support: 1.800.668.9318
Email: [e-mail]
Web: www.nienkamper.com
Page 4 of 4
THIS IS A GENERAL ASSEMBLY GUIDE, NOT ALL CONDITIONS MAY APPLY TO YOUR
PARTICULAR INSTALLATION.
To wire the unit, plug all light cables into driver provided. Note: larger units include additional extension cables that need to be
plugged into light cables not long enough to reach driver. This step applies to both strip and pot lights. If your unit includes a case
mounted switch, install by feeding cable and plug through the unit top. Plug switch into switch port in driver. Shelf mounted switches
are install in the same way in shelf but cables are routed down gable with light cables. Once all lighting an switch are connected,
secure driver to back of case using the adhesive strip and #6 x 5/8” pan head wood screws. Use adhesive wire manager clips to
manage any excess cable. Plug power cable into driver and attach to building power supply.
To install removable back, align modeze screws in finished back with clips
pre-installed in case. Push panel in and down to lock.
Switch
Light cable
Driver
Power cable
P/N _________________ 06-9-20