Nienkamper Nomad User manual

Tel [phone]
Tel [phone]
Fax [phone]
mail@ nienkämper.com
www.nienkamper.com
CONFERENCE TABLE & POWER UNIT
INSTALLATION GUIDE
FLAT HEAD HEX SO C KET ASSEMBLY
4mmand5mm-2"x1/4"-20and threaded collar.
J oins ra ils to ge the r.
BUTTON HEAD CAP SCREW
4mm - 3/8”-16 x 1”.
Joins leg to rail.
ALLAN KEYS
Sma ll 4 mm
Fo r he x so c ke t a sse m bly, to join ra ils to ge the r.
Fo r in sta lling b a se s to ra ils.
For insta lling mounting pla te to top.
La rg e 5 m m
Fo r he x so c ke t a sse m bly, to join ra il to ge the r.
HARDWARE PARTS LIST
WOO DEN SPLINE
1/8"x7/8" x (24" - va ries).
Inserts into the edge of
m ultip le se g m e nt top s.
MOUNTING PLATE
1/4"x3"x4".
Fixe s ra il to to p.
TI G H T J O I N T
FASTENERS
3pieceassembly
p lus 1 tig h te nin g ro d .
FLAT HEA D HEX SO C KET BO LT
4mm-1"x1/4"-20.
Joins mounting plate to top.
Joins ba ses to top for ta ble s up to 108".
WIRE MANAG EMENT
“U” CLIPS
Grey ABSplastic.
Use d to se c ure w ire s to
sup p o rt ra il.
Nomad Base
Nomad
™
THIS IS A GENERAL ASSEMBLY GUIDE, NOT ALL CONDITION MAY APPLY TO YOUR PARTICULAR INSTALLATION

12
A SSEMBLING SUPPO RT RA ILS ATTA C HING BA SE TO RA ILS
• Large conference tables incorporate support rails in multiple segments.
• Po sitio n a nd a sse m b le c o nne c ting jo ints a s sh o wn .
• Matching jointsare numbercoded (circularlabels).
• Required hardware: 2" x 1/4" - 20 at head hex socket assembly.
• Tighten joint, a ligning ma rks a s shown.
• C e rta in ta b le sha p e s re q uire ra ils to b e a sse mb le d a t d ie re nt a ng le s
(as marked).
• With leg upside down and rail positioned so 3/8”dia. holes face inward,
slide leg tab into end of rail and secure with 3/8”-16 x 1” button head screw.
• Measure and mark center distance to position cross rail
according to your specic order.
34
• Loosen Gripper tting socket head cap screw and push tting
and cross rail into marked position, tighten to secure.
JO INING MULTIPLE PIEC E TO PSFINISHED BASE ASSEMBLY
Po sition m ultiple se c tio n top s w ith m a tc h ing id e ntic a tio n nu m b e rs
onto ra ils.
Inse rt w oo d e n sp line into the g roo ve a t the se a m .
Inse rt b a ll tting , a lign with tight joint b olt.
Sta rt the thre a d.
Slid e to p s to g e the r, a lig n the to p .
Inse rt tig h t jo int c o lla r.
Tig hte n ba ll tting, ha nd tig ht.
• Flip assembly over to apply top.

SMUROFXOVGNILLATSNIATTACHING RAIL TO TOP
®
56
Inse rt the mounting p la te into the top groove of the ra il.
Slide the plate to align threaded inserts of top with holes
in m o u ntin g p la te .
Require d ha rdwa re : 1" x 1/4"-20athead hexbolt.
Unpa c k the Forum box a nd re trie ve the swive l la tc he s.
C a re fully thre a d p la stic thumbsc re w s into inse rts a round the squa re
hole in the top.
Position Fo rum in o pe ning a nd c a re fully e a se up into the sq ua re hole .
Rota te the swive l c a tc he s a nd tighte n the thum b sc re w fa ste ne rs.
Note: detailed installation instructions are included with allVox Forums.
“U” CLIPSINSTALLING EDGE POWER UNIT
Unpack power unit and install in rebates machined under top using wood
screws provided with unit.
Screw “d” ring cable manager into place in front of cable rebate.
Feed power cable under rail via wire rebate and plug into surge protector
or route to building power according to your specic table.
• Using wire ma na ge me nt “ U”
clips, along the rail.
sto re a nd ro ute c a b le s to cable
manager.
• To bring c a bling from the under
side o f the top to the o or, w ire
managementaccessoriescan
be used.
• A variety of models are available.
• Instruc tions for insta lling wire
ma na ge me nt a c c essories a re
packaged with each accessory.
WIRE MANAGEMENT