Ninja BL682UKCO User manual

®BL682UKCO
OWNER’S GUIDE
www.ninjakitchen.eu
0800 862 0453

10800 862 0453
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR NUTRI NINJA®
| NINJA®
BLENDER SYSTEM WITH AUTO-IQ®
TECHNOLOGY.
WARNING: Extension cords are not
recommended for use with this product.
WARNING: The blades are not affixed to
the unit. They are removable and very sharp.
Handle with care!
CAUTION: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through
an external switching device, such as a
timer, or connected to a circuit that is
regularly switched on and off by the utility.
IMPORTANT: This appliance is not intended
for use by persons with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children shall not use or play with this
appliance. Close supervision is necessary to
keep appliance and cord out of reach of children
during use.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY:
1. CAUTION: The blades are not affixed to
the unit. They are removable and extremely
sharp. When handling the stacked blades or
the chopping blades, do not hold the blades
but rather always hold the shaft. Blades are
sharp. Handle carefully!
2.
CAUTION: DO NOT BLEND HOT LIQUIDS.
Allow the liquids and foods to cool to room
temperature before blending.
3. CAUTION: Do not blend dry ingredients
unless pulsing for short intervals per the
instructions. Continuous blending dry
ingredients will overheat the blender.
4. To protect against electrical shock, do not
submerge the appliance or allow the power cord to
come into contact with water or any otherliquid.
5. DO NOT allow young children to operate the
appliance or use as a toy. Close supervision is
necessary when any appliance is used near children.
6. Never leave an appliance unattended when in use.
7. Turn the appliance off and remove the power cord
from the electrical outlet when not in use, before
assembling or disassembling parts, accessing
parts that move while in use and before cleaning.
To unplug, grasp the plug and pull from the
electrical outlet. Never pull from the power cord.
8. DO NOT abuse the power cord. Never carry
the appliance by the power cord or yank it to
disconnect from electrical outlet; instead, grasp
the plug and pull to disconnect.
9. DO NOT use with damaged cord or plug.
10. DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged or
left outdoors.

2
www.ninjakitchen.eu
27. Max ON time is 60 seconds under 1500W load.
If the appliance overheats, a thermal switch will
become activated and shut off the motor. To
reset, unplug the appliance and let it cool down
for approximately 15 minutes before using again.
28. In the event that the unit overloads, the control
panel lights will flash and the unit will shut down.
Unplug the appliance and let it cool down for
approximately 15 minutes before using again.
29. Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running
the PULSE function up to an additional 30 Pulses.
30. The maximum rating is based on the stacked
blade (pitcher) that drives the greatest power
and other recommended attachments may draw
significantly less power or current.
31. To avoid injury, never attempt to place the Pro
Extractor Blade™onto the motor base without first
assembling the blade assembly to the Nutri Ninja®
Cup.
32. Appliance accessories are not intended to be
used in the microwave as it may result in damage
to the accessories
33. THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use this
appliance for anything other than its intended use.
Do not use outdoors.
34. DO NOT remove lid until blade has COMPLETELY
STOPPED.
35. DO NOT attempt operation without the cover
being in place.
36. DO NOT process liquid ingredients in the coffee
grinder. Accessory is not intended for liquid
processing.
37. DO NOT attempt to chop ice in the coffee grinder.
38. Check coffee grinder for presence of foreign
objects before using.
11. NO SERVICEABLE PARTS. Incorrect re-assembly
or repair can cause a risk of electrical shock or injury
to persons when the appliance is used. Contact
Customer Service.
12. Always use the appliance on a dry, level surface.
13. Keep hands, hair, clothing, as well as utensils
out of container while processing or blending
to reduce the risk of severe injury to persons or
damage to the appliance. A scraper may be used
but only when the appliance is not running.
14. Avoid contact with moving parts.
15. DO NOT attempt to sharpen blades.
16. DO NOT use the appliance if either set of blades
are bent or damaged.
17. To reduce the risk of injury, never assemble the
stacked blades in the pitcher or the chopping
blade in the bowl without the pitcher or the bowl
properly attached to the motor base.
18. DO NOT operate this appliance on or near any hot
surfaces (such as gas or electric burner or in a
heated oven).
19. The use of attachments or accessories
including canning jars, not recommended by the
manufacturer may result in fire, electric shock or
personal injury.
20. DO NOT remove any container from the motor
base while the appliance is in operation. Always
unplug the unit when not in use.
21. To reduce the risk of injury, NEVER operate the
appliance without the lid in place; DO NOT try to
defeat or bypass the interlock mechanism. When
using the removable blades, make sure they are
properly installed before operating the appliance.
22. DO NOT expose containers to extreme
temperature changes.
23. Extreme caution must be used when moving an
appliance containing hot food, water or other liquids.
24. DO NOT overfill. DO NOT exceed “MAX” fill line.
25. DO NOT operate the appliance empty.
26. To reduce the risk of burns, always allow the
appliance to cool before taking off parts and
before cleaning.
SAVE THESE
INSTRUCTIONS

30800 862 0453
THIS BOOK COVERS MODEL NUMBERS:
BL68UKCO 30
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1500W
Pitcher Capacity: 2.1 L
Max Liquid: 2 L
Bowl Capacity: 1.8 L
Nutri Ninja®
Cup Capacity: 500ml
650ml
Coffee and Spice
Ninja Grinder: 10 tbsp
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and
electronic equipment (WEEE).
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material sources. To return your used device, please use the return and collection
systems or contact the retailer where this product was purchased. They can take this
product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility (EMC)
2004/108/EC and its revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.
Guarantee: This product is unconditionally guaranteed for one year against all defects of
workmanship and materials. This guarantee does not affect your statutory rights. If this product
proves unsatisfactory please contact our customer service department on freephone 0800 862 0453
or by e-mail [e-mail].

4
www.ninjakitchen.eu
Contents
Thank you for
purchasing the
Nutri Ninja®
|
Ninja®Blender
System with
Auto-iQ®
Technology.
Getting to Know Your Nutri Ninja | Ninja Blender System with Auto-iQ Technology...............5
Using the Nutri Ninja | Ninja Blender System with Auto-iQ Technology ...............................7
Assembly and Use for the Blender..........................................................................8
Assembly and Use for the Processor Bowl ............................................................10
Assembly and Use for the Nutri Ninja....................................................................12
Use of the Coffee and Spice Ninja Grinder.............................................................13
Programs, Speed Settings, & Uses for the Blender Pitcher ..............................................14
Programs, Speed Settings, & Uses for the Nutri Ninja Cups .............................................14
Programs, Speed Settings, & Uses for the Processor Bowl..............................................15
Speed Setting & Uses for the Coffee and Spice Ninja Grinder..........................................15
Care & Maintenance ....................................................................................................16
Troubleshooting Guide..................................................................................................17

50800 862 0453
Getting To Know Your Nutri Ninja®
|
Ninja®Blender System with
Auto-iQ®Technology
e
1500
WATTS
AUTO
AUTO
AUTO
AUTO
AUTO
ON/ OFF
MARCHE
/ARRÊT
FROZENDRINKS
SMOOTHIES
BOISSONSCONGELÉES
FOOD PURÉE
PURÉE D’ALIMENTS
MEDIUM
MOYEN
HIGH
ÉLEVÉ
PULSE
IMPULSION
ULTRABLEND
ULTRAMÉLANGE
BLEND
MÉLANGE
LOW/ DOUGH
BAS/ PÂ TE
fFood Processor Bowl
gFood Processor Lid
h Chopping Blade (food processor)
i Dough Blade (food processor)
a650 ml Nutri Ninja Cup
b500 ml Nutri Ninja Cup
cSip & Seal®Lid (x2)
dPro Extractor Blades™
e Coffee and Spice Ninja Grinder
jBlender Pitcher
kBlender Lid with locking handle
l Stacked Blades (blender)
mMotor Base
j
k
l
m
f
h
g
b
dc
a
i
NOTE: Blades are not interchangeable.

6
www.ninjakitchen.eu
The Nutri Ninja®
|
Ninja®Blender System with Auto-iQ®Technology is a high powered innovative tool with a sleek design
and outstanding performance, a true asset to any kitchen. The Nutri Ninja
|
Ninja Blender System with Auto-iQ Technology
features intelligent programs that combine pulsing, blending and pausing patterns that do the work for you! Get great
results every time with no guesswork required! For best results, be sure to carefully read all the instructions contained in
the manual before using this appliance.
Nutri Ninja
|
Ninja Blender System with Auto-iQ Technology Features:
• PatentPendingNinjaBladeTechnology
• BPAFreeBlenderPitcher(maximumliquidcapacity2L),NutriNinjaCups,FoodProcessorBowlandLids
• Drip-FreePourSpout
• TotalCrushing®Technology
• LEDControlPanelwithTimer
• Sturdy,Non-SlipBase
• SmartLidtechnologyforeasyrelease
• 3speeds:Low/Dough,Medium,&High
• 5Auto-iQsettings-Auto-iQFrozenDrinks/Smoothies,Auto-iQFoodPuree,NutriNinjaAuto-iQBlend,
Nutri Ninja Auto-iQ Ultra Blend and Auto-iQ Pulse
• NutriNinjaNutrient&VitaminExtraction
• CoffeeandSpiceNinjaGrinder,BPAfreelid

70800 862 0453
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
WARNING: Never leave the appliance
unattended while in use.
CAUTION: DO NOT BLEND HOT LIQUIDS.
Allow liquids and foods to cool to room
temperature before blending.
CAUTION: Blade assemblies are sharp! Use
extreme caution when handling the blade
assemblies. Always hold them by the shaft.
CAUTION: Never remove the container while
the appliance is still running.
CAUTION: We do not recommend grinding in
any of our Nutri Ninja Cups.
IMPORTANT: Never add ingredients into the
container before placing the blade in first.
IMPORTANT: Blade assemblies are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.
CAUTION:
Stacked Blades
are not locked
in place. If using
the pour spout,
ensure that the
lid is fully locked
onto the blender
pitcher.
CAUTION: Stacked
Blades are not
locked in place.
If pouring with
the lid removed,
ALWAYS remove
the blade
assembly first
before pouring.
CAUTION: Blade assemblies are sharp, not locked
in place and removable, handle with care. When
handling the blade assemblies, always hold them
by the shaft.
BEFORE FIRST USE
1Remove all packaging material and labels from the
appliance.
2Wash the lids, pitcher, bowl, Nutri Ninja cups, grinder
and blade assemblies in warm, soapy water with a soft
cloth.
CAUTION: Handle the blade assemblies with care
when washing as the blades are very sharp.
3Rinse and dry thoroughly.
4The lids, pitcher, bowl, Nutri Ninja cups, grinder
and blade assemblies are all dishwasher safe. It is
recommended that the lids and blades be placed on the
top rack. Ensure that the blades are removed from the
containers before placing in the dishwasher.
5Wipe the motor base clean with a damp cloth.
Using the Nutri Ninja®
|
Ninja®Blender System with Auto-iQ®Technology

8
www.ninjakitchen.eu
Assembly and Use for the Blender
1Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the attachment is seated properly and is
standing upright. (Fig. 1)
NOTE: The blade will fit loosely on the drive gear.
2Place the motor base on a clean, dry, level surface such
as a counter or table top.
3 Align and lower the Pitcher onto the motor base.
(Fig. 2) Handle should be aligned slightly to the right
of the “LOCK” symbol on the motor base.
4Rotate the pitcher clockwise until it locks in place, you
will hear a click when the lock is engaged. (Fig. 3)
5The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 4a, Fig. 4b)
6Add the ingredients to the pitcher, making sure that
they do not exceed the highest measured marking line
on the side of the pitcher.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
“MAX LIQUID” mark (2 L) on the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
7Holding the lid by the handle in the upright position, place
it on top of the pitcher aligning the triangle ( ) located on
the lid with the triangle ( ) located on the pitcher’s handle.
(Fig. 5a) Press the handle down until you hear a click.
The triangles on the lid and the blender handle MUST be
aligned in order for the blender to turn on. (Fig. 5b)
8Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power light
() will flash and the motor will not work if the
pitcher and lid are not installed correctly. When
the pitcher and lid are installed properly, the
power light ( ) will be solid, indicating that the
appliance is ready for use.
ASSEMBLY
Fig. 2
Fig. 5a
Fig. 4a Fig. 4b
Fig. 1 Fig. 3
Fig. 5b
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
MED
LOW/
DOUGH
HIGH PULSE
LOW DOUGH
SMOOTHIE SINGLE
SERVE
PUREE FROZEN
BLENDING
MED
LOW/
DOUGH
HIGH PULSE
LOW DOUGH
SMOOTHIE SINGLE
SERVE
PUREE FROZEN
BLENDING
MED
LOW/
DOUGH
WARNING: Never leave the appliance unattended while in use.
CAUTION: Stacked Blades are sharp, not locked in place and removable, handle with care. When handling
the Stacked Blades, always hold them by the shaft.
IMPORTANT: Make sure that the motor base is plugged in for use.

90800 862 0453
NOTE: Nutri Ninja®
|
Ninja®Blender System with Auto-
iQ®Technology can sense which jar is on the motor
base. The function lights will illuminate depending on
which jar is placed on the motor base. (Fig. 6)
9Press the power button to turn on the unit. Select
the speed or Auto-iQ program that best suits your
needs. The Auto-iQ program will stop the appliance
automatically at the end of the program. (Fig. 7)
NOTE: Pulse ingredients for even chopping by holding
the Auto-iQ Pulse button until your desired consistency
is reached.
NOTE: Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running the
PULSE function up to an additional 30 Pulses.
10 To pause the appliance, press the selected speed or
Auto-iQ Program a second time. (Fig. 8)
11 When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade to stop turning. (Fig. 8)
12 Turn the pitcher anticlockwise to remove and then lift
off the base. (Fig. 9)
CAUTION: Never insert your hands in the pitcher
as the Stacked Blades are sharp. Always use a
spatula to dislodge food that has stuck to the
sides of the pitcher.
CAUTION: If using the pour spout, ensure that the
lid is fully locked onto the blender pitcher.
CAUTION: If pouring with the lid removed, ALWAYS
remove the blade assembly first before pouring.
13 Depending on the consistency of the contents in the
container, open the pour spout cap and use the spout
to empty liquid contents.
14 For thicker consistencies, remove the lid and blade
attachment carefully (by its shaft), then empty contents
from the container. To remove the lid, press the release
button on the lid and pull the lid handle up to a 90°
angle and lift the lid off the blender pitcher. (Fig. 10)
15 Make sure that the unit is unplugged when not in use.
16 To release the motor base from the counter or table top,
place your hands underneath both sides of the motor base
and gently pull the unit up and towards you. (Fig. 11)
Assembly and Use for the Blender - cont.
Fig. 8
USE REMOVAL
Fig. 6
Fig. 9Fig. 7 Fig. 10 Fig. 11
WARNING: Never leave the appliance unattended while in use.
CAUTION: Stacked Blades are sharp, not locked in place and removable, handle with care. When handling
the Stacked Blades, always hold them by the shaft.
IMPORTANT: Make sure that the motor base is plugged in for use.

10
www.ninjakitchen.eu
Assembly and Use for the Processor Bowl
ASSEMBLY
MED
LOW/
DOUGH
Fig. 5a Fig. 5b
MED
LOW/
DOUGH
Fig. 2
MED
LOW/
DOUGH
Fig. 3
Fig. 1
MED
LOW/
DOUGH
Fig. 4
Fig. 6a
Fig. 6b
NOTE: Nutri Ninja
®
|
Ninja
®
Blender System with
Auto-iQ
®
Technology can sense which jar is on the
motor base. The function lights will illuminate depending
on which jar is placed on the motor base. (Fig. 1)
1 Holding the desired blade by the top of the shaft, place it onto
the drive gear inside the bowl. Ensure that the attachment is
seated properly and is standing upright. (Fig. 2)
NOTE: The blade will fit loosely on the drive gear.
2Place the motor base on a clean, dry, level surface such
as a counter or table top. Press down on the motor
base to make sure that the suction cups adhere to the
counter or table top.
3 Align and lower the Processor Bowl onto the motor
base. (Fig. 3) Handle should be aligned slightly to the
right of the “LOCK” symbol on the motor base.
4Rotate the bowl clockwise until it locks in place, you will
hear a click when the lock is engaged. (Fig. 4)
5The bowl can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 5a, Fig. 5b)
6Add the ingredients to the bowl, making sure that they
do not exceed the “MAX” fill line on the side of the bowl.
7Holding the lid by the handle in the upright position,
place it on top of the Processor Bowl aligning the
triangle ( ) located on the lid with the triangle ( )
located on the Processor Bowl handle. (Fig. 6a) Press
the handle down until you hear a click. The triangles on
the lid and the Processor Bowl handle MUST be aligned
in order for the blender to turn on. (Fig. 6b)
NOTE: The 1.8 L bowl is not intended for blending
drinks. Do not overfill.
8 Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power
button ( ) will flash and the motor will not work
if the bowl and lid are not installed correctly.
When the bowl and lid are installed properly, the
power button ( ) will be solid, indicating that the
appliance is ready for use.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Chopping Blade is sharp, not locked in place and removable, handle with care. When handling
the Chopping Blade, always hold by the shaft.
IMPORTANT: Make sure that the motor base is plugged in for use.

11 0800 862 0453
Assembly and Use for the Processor Bowl - cont.
REMOVAL
Fig. 2 Fig. 3 Fig. 4
USE
Fig. 5
USE
Fig. 1
USING THE CHOPPING BLADE
1Holding the Chopping Blade by the shaft, place it
onto the gear shaft inside the bowl. Ensure that the
attachment fits around the gear shaft and that it is
standing straight.
2 Add the ingredients and secure the bowl lid onto the
bowl. (Fig. 1)
3Plug the power cord into the electrical outlet and press
on the power button ( ). Select the speed or Auto-iQ®
program that best suits your needs. Pulse ingredients
for even chopping by holding the Auto-iQ Pulse button
until your desired consistency is reached.
NOTE: Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running the
PULSE function up to an additional 30 Pulses.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
4When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade to stop turning. (Fig. 2)
5To remove the lid, press the release button on the lid
and pull the lid handle up to a 90°angle. (Fig. 2)
6Turn the bowl anticlockwise and lift it to remove it from
the motor base. (Fig. 3)
CAUTION: If pouring from the bowl, ALWAYS
remove the blade assembly first before pouring.
7To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you. (Fig. 4)
USING THE DOUGH BLADE
1Holding the dough blade by the shaft, place it onto the
gear shaft inside the bowl. Ensure that the attachment
fits around the gear shaft and that it is standing straight.
(Fig. 5)
2Add the ingredients and secure the bowl lid onto the bowl.
3Plug the power cord into the electrical outlet and press
on the power button ( ). Select LOW/DOUGH on the
control panel and process until ingredients come
together to form a mass.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
4Once finished making dough, stop the appliance by
pressing the power button ( ) and wait for the blade to
stop turning.
5To remove the lid, press the release button on the lid
and pull the lid handle up to a 90°angle. (Fig. 2)
6Turn the bowl anticlockwise and lift it to remove it from
the motor base. (Fig. 3)
7To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you.
(Fig. 4)
WARNING: Never leave the appliance unattended while in use.
CAUTION: Chopping Blade is sharp, not locked in place and removable, handle with care. When handling
the Chopping Blade, always hold by the shaft.

12
www.ninjakitchen.eu
7Once you have reached your desired consistency, turn the
power button off. Turn the Nutri Ninja cup anticlockwise
and pull straight up to remove. (Fig. 5, Fig. 6)
NOTE: Do not overfill! To avoid spilling, do not add
ingredients past the “MAX” fill line.
8Turn the cup upright and remove the Pro Extractor
Blades by twisting the blade assembly anticlockwise.
9Place the Sip & Seal®lid onto the Nutri Ninja cup, twist
to seal and enjoy!
10 Make sure that the motor base is unplugged when not
in use.
11 To release the motor base from the counter or table top,
place your hands underneath
both sides of the motor base
and gently pull the unit up and
towards you. (Fig. 7)
Assembly and Use for the Nutri Ninja®
Fig. 3 Fig. 4 Fig. 5 Fig. 6
Fig. 1
NOTE: Nutri Ninja
|
Ninja®Blender System with Auto-
iQ®Technology can sense which jar is on the motor
base. The function lights will illuminate depending on
which jar is placed on the motor base. (Fig. 1)
1Place the motor base on a clean, dry, level surface such as a
counter or table top. Press down on the motor base to make
sure that the suction cups adhere to the counter or table top.
2Add ingredients to the Nutri Ninja cup.
3Place the Pro Extractor Blades onto the cup and tightly
screw it on clockwise until you have a good seal. (Fig. 2)
4Turn the Nutri Ninja cup upside down and place it onto the
motor base, aligning the tabs on the cup with the motor
base. Rotate the Nutri Ninja cup clockwise until it locks in
place, you will hear a click when the lock is engaged. (Fig. 3)
5Press the power button on, and select the speed or
Auto-iQ program that suits your needs. The
Auto-iQ program will stop the appliance automatically
at the end of the program. (Fig. 4)
6. To pause the appliance, press the selected speed or
Auto-iQ Program a second time. Fig. 7
ASSEMBLY USE REMOVAL
Fig. 2
or or
WARNING: Never leave the appliance unattended while in use.
CAUTION: Pro Extractor Blades™are sharp and removable, handle with care. When handling the Pro
Extractor Blades, do not hold the blades, always hold by the base of the Pro Extractor Blades.
CAUTION: DO NOT BLEND HOT LIQUIDS. Allow the liquids and foods to cool to room temperature before blending.
IMPORTANT: Make sure that the motor base is plugged in for use.
IMPORTANT: When processing soft dry ingredients such as day-old bread or cheese use quick, short 1
second pulses. Do not overfill to avoid overheating the appliance. Allow the appliance to cool after each use.

13 0800 862 0453
6 Use only HIGH setting in short intervals until you reach
your desired consistency. (Fig. 3)
7 To remove the grinder, ensure that the motor has
stopped running. Do not remove cover until blade
has completely stopped. Then turn the grinder
anticlockwise (Fig. 4) and pull straight up to remove.
(Fig. 5)
8Remove the blade assembly with stainless steel
grinding cup by twisting the lid anticlockwise. Be sure
to store the grinder with the lid attached.
10 Make sure that the motor base is unplugged when not
in use.
11 To release the motor base
from the counter or table top,
place your hands underneath
both sides of the motor base
and gently pull the unit up and
towards you. (Fig. 6)
1Place the motor base on a clean, dry, level surface such
as a counter or table top. Press down on the motor
base to make sure that the suction cups adhere to the
counter or table top.
2Make sure that the motor base is plugged in for use.
Lights will not yet illuminate.
3Add ingredients to the stainless steel grinding cup. Use
the measurement lines on the grinding cup for added
convenience!
NOTE: Do not overfill! To avoid spilling, do not add
ingredients past the “MAX” fill line.
4Place the lid onto the blade assembly with stainless
steel grinding cup so that the tabs on the cup meet the
entry point on the blade assembly. Twist until the lid is
locked in place. (Fig. 1)
5Place the grinder onto the motor base, aligning the tabs
on the grinder with the motor base. Turn it clockwise,
until you feel it click into place. (Fig. 2)
Use of the Coffee and Spice Ninja®Grinder
ASSEMBLY USE REMOVAL
WARNING: Never leave the appliance unattended while in use.
CAUTION: Handle the blade assembly of the stainless steel grinding cup with care as the blades are very sharp.
WARNING: Do not process liquid ingredients. The grinder accessory is not intended for liquid processing.
Do not attempt to chop ice.
CAUTION: Check the grinding cup for presence of foreign objects before using.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5
Fig. 6

14
www.ninjakitchen.eu
Speed Setting & Uses for the Blender Pitcher
Speed Setting & Uses for the Nutri Ninja®Cup
FUNCTION CONTAINER BLADE
TYPE SPEED or PROGRAM TYPE OF FOOD
Smoothies Nutri Ninja Cup Pro Extractor
Blades™Nutri Ninja Auto-iQ Blend
Smoothies
Frappes
Milkshakes
Protein Drinks
Green Smoothies Nutri Ninja Cup Pro Extractor
Blades
Nutri Ninja Auto-iQ Ultra
Blend
Frozen Fruits
Frozen Vegetables
Kale
Celery
Spinach
Seeds
Ice
Grating Nutri Ninja Cup Pro Extractor
Blades
Auto-iQ Pulse
Nutri Ninja Auto-iQ Blend
High
Grated Cheese
Bread Crumbs
Chopping Nutri Ninja Cup Pro Extractor
Blades
Auto-iQ Pulse
Nutri Ninja Auto-iQ Blend
High
Salsa
Vegetables
Nuts
FUNCTION CONTAINER BLADE
TYPE SPEED or PROGRAM TYPE OF FOOD
Frozen Drinks /
Ice Crush Blender Pitcher Stacked Blade Auto-iQ®Frozen Drinks/ Smoothies
Ice
Frozen Drinks
Smoothies
Pureeing Blender Pitcher Stacked Blade Auto-iQ Food Puree
Smoothies
Soups
Milkshakes

15 0800 862 0453
Speed Setting & Uses for the Processor Bowl
FUNCTION CONTAINER BLADE
TYPE SPEED or PROGRAM TYPE OF FOOD
Mincing Food Processor
Bowl
Chopping
Blade Auto-iQ®Pulse
Onion
Garlic
Herbs
Kneading and
Dough Mixing
Food Processor
Bowl Dough Blade Low/Dough
Bread Dough
Pie Dough
Pizza Dough
Pretzel Dough
Cookie Dough
Processing Food Processor
Bowl
Chopping
Blade
Auto-iQ Food Puree
Low/Dough
Medium
High
Pâtés
Stewed Fruits
Dips
Apple Sauce
Spreads
Baby Food
Emulsifying Food Processor
Bowl
Chopping
Blade
Low/Dough
Medium
Salad Dressings
Dips
Sauces
Grinding Food Processor
Bowl
Chopping
Blade Medium Meat
Grating Food Processor
Bowl
Chopping
Blade Auto-iQ Pulse
Grated Cheese
Bread Crumbs
Spices
Chopping Food Processor
Bowl
Chopping
Blade Auto-iQ Pulse
Salsa
Vegetables
Nuts
Batters Food Processor
Bowl Dough Blade Low/Dough Cake Mixes Batters
Speed Setting & Uses for the Coffee and Spice Ninja®Grinder
FUNCTION CONTAINER BLADE
TYPE SPEED or PROGRAM TYPE OF FOOD
Grinding Coffee and Spice
Ninja Grinder Grinder High Coffee Spices

16
www.ninjakitchen.eu
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
CAUTION: Use caution when handling the blade
assemblies as the blades are very sharp.
1Separate/remove all parts from each other.
2 Clean the motor base with a damp cloth and wipe dry.
3Place the lids, pitcher, bowl, Nutri Ninja®cups, grinder
and blade assemblies in the dishwasher. Place the lids
and attachments on the toprack.
OR
4Carefully hand wash the lids, pitcher, bowl, Nutri Ninja
cups, grinder and blade assemblies in warm, soapy
water with a soft cloth.
Please call customer service if any servicing needs to
be performed on the appliance at 0800 862 0453.
Care & Maintenance
HOW TO STORE
1 Store the Nutri Ninja | Ninja Blender System with Auto-iQ
®
Technology upright with the pitcher on the motor base,
stacked blade inside the pitcher and lid on the pitcher. Do
not place anything on top. Store the Food Processor Bowl
with the chopping blade inside and the lid on top. Store
the Nutri Ninja cup and the rest of the attachments along
side the appliance or in a cabinet where they will not be
damaged and won’t cause a hazard. Be sure to store the
grinder with lid attached.
RESETTING THE MOTOR THERMOSTAT
The Nutri Ninja | Ninja Blender System with Auto-iQ
Technology features a safety system which prevents
damage to the unit’s motor and drive system should you
inadvertently overload your appliance. If the appliance
is being overloaded, the motor will stop. Allow
the appliance to cool for approximately 15
minutes. To reset the appliance, follow the resetting
procedure below:
1Unplug the appliance from the electrical outlet.
2Remove and empty the container and ensure that no
food is jamming the blades or attachments.
3Allow the appliance to cool for approximately 15
minutes.
4Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5 Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.

17 0800 862 0453
Troubleshooting Guide
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor Doesn’t Start or
Attachment Doesn’t Rotate.
Make sure the container is securely locked into the motor base.
Make sure the lid is securely on container in the correct position (align arrows).
The appliance is turned “Off”. Press the power button ( ) to turn “On”.
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power light will flash.
Unplug and wait approximately 15 minutes before using again.
The unit has overheated. Unplug and wait approximately 15 minutes before using again.
Check to make sure the unit is not overloaded.
Food is Unevenly Chopped.
Either you are chopping too much food at one time, or the pieces are not of even
size and processing smaller amounts per batch.
Food is Chopped Too Fine or is
Too Watery.
The food has been over processed. Use Auto-iQ®Pulse button for controlled
processing.
Food Collects On Lid or On the
Sides of the Container.
The mixture is too thick. Add more liquid.
You Cannot Achieve Snow
From Solid Ice.
Do not use ice that has been sitting out or has started to melt. Use ice straight
from the freezer.
Start with a few pulses and then go to a continuous blending cycle.
Motor Base Won’t Stick to
Counter or Table Top.
Make sure surface and suction feet are wiped clean. Suction feet will only stick to
smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood,
tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to a surface that
is not secure, (cutting board, platter, plates, etc.).
You get an “Err” Message.
Your Ninja®is able to detect which jar is on the base. You may be trying to use a
program that is not designed for the jar you have installed. The programs will light
up indicating which programs are available for each jar.
You have a blinking red light.
The unit is not installed properly. For your safety the unit will only be able to be
turned on when it is properly assembled. Please refer to the assembly pages of
this inspiration guide for assistance.

18
www.ninjakitchen.eu
Notes

Euro-Pro Europe Limited
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
Freephone 0800 862 0453
www.ninjakitchen.eu
Copyright © 2015 Euro-Pro Operating LLC
Auto-iQ,Euro-Pro, Nutri-Ninja, Ninja, Sip & Seal and Total
Crushing are registered trademarks of Euro-Pro Operating LLC.
Pro Extractor Blades is a trademark of Euro-Pro Operating LLC.
Printed in China
Illustrations may differ from actual product. We are constantly
striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
BL682UKCO_30_IB_150728_1