Nokia 220 User manual

Send feedback
Recommend Change in
KICS
Rate this page in KICS
E-mail
[email protected]
Service Manual for L1 and L
2
Nokia 220
RM-969 (DS), RM-970 (SS)
,
RM-971 (SS)
Key features

2,4" QVGA display with 320 x 240 resolution

MicroSD card support up to 32 GB

Nokia Slam support

2 MP camera

Micro USB for charging and file transfer
Version 1.0
CHECK THE REPAIR
POLICY BEFORE
PERFORMING ANY
MECHANICAL REPAIR ON
SERVICE LEVEL 1&2!
Exploded view Disassembly steps
Assembly steps Solder components Service devices
Product controls and interfaces Service concept
More More
More More More
More More
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia 220
RM-969, RM-970, RM-971
Version 1.0
Version history
Version Date Description
1.0 21.02.2014 First published version
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia 220
RM-969, RM-970, RM-971
Version 1.0
Exploded view
A-COVER
I0001
LIGHT SWAP PWB
I0006
EARPIECE
I0013
UI SHIELDING
I0003
CAMERA
I0010
HEADSET JACK
I0015
SPEAKER ADHESIVE
I0016
EARPIECE GASKET
I0014
KEYMAT
I0002
DISPLAY
I0004
DOMESHEET
I0005
TYPE LABEL
I0009
SPEAKER GASKET
I0012
D-COVER
I0017
SPEAKER MESH
I0018
B-COVER
I0020
SPEAKER
I0011
FEM SHIELDING LID
I0008
BB SHIELDING LID
I0007
SCREW TORX+ SIZE 4
M1.4 x 0.75 - 4.5
I0019
LIGHT SWAP PACKAGE
(I0005 - I0009)
1
D-COVER ASSEMBLY
(I0014 - I0018)
2
Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia 220
RM-969, RM-970, RM-971
Version 1.0
Disassembly steps
1) For disassembling you need the Nokia Standard toolkit version 2 and an AV plug.
2) Protect the A-COVER with protective film.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

3) Push from the camera opening to release the B-COVER. Remove the B-COVER.
4) If there is battery inserted, remove it by using the shown opening. Lift up and remove the BATTERY.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

5) Unscrew the four Torx+ size 4 screws in the order shown. Do not use them again. Discard them.
6) To release the A-COVER open the shown clips with the SRT-6. Start from the top end of the device.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

7) Open the clip on the bottom end of the device with the SRT-6.
8) Open also the clips on the other side with the SRT-6.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

9) The A-COVER can now be separated.
10) Protect the DISPLAY with protective film.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

11) Protect the other side of the A-COVER with protective film.
12) Use the sharp end of the SS-93 to relase the shown clips holding the KEYMAT. Open the two clips near
the A-COVER window first.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.

13) The KEYMAT can now be separated.
14) Use the SS-93 to open the four clips holding the ENGINE BOARD.
©2014 Nokia | Nokia Internal Use only | All Rights Reserved.