Nokia BH-904 User manual

Copyright © 2009 Nokia. All rights reserved.
Nokia Bluetooth Headset BH-904
10
1
3
4
5
67
8
2
9
9

Copyright © 2009 Nokia. All rights reserved.
12
13
11
14 15

3
Copyright © 2009 Nokia. All rights reserved.
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares
that this HS-101W product is in
compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC. A copy
of the Declaration of Conformity can be
found at http://www.nokia.com/phones/
declaration_of_conformity/.
© 2009 Nokia. All rights reserved.
Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
Introduction
With the Nokia Bluetooth Headset
BH-904, you can make and answer
calls hands-free with your
compatible mobile device. The
headset is provided with a sliding
boom that allows you to talk at a
lower volume or in a noisy
environment. Noise cancellation
helps you handle calls in noisy
environments.
Read this user guide carefully before
using the headset. Also, read the
user guide for the device that you
connect to the headset.
Note: The surface of this
device does not contain
nickel in the platings. The
surface of this device
contains stainless steel.
Bluetooth compatibility
The headset is compliant with the
Bluetooth Specification 2.1 + EDR
supporting the Headset Profile 1.1
and Hands-Free Profile 1.5. Check
with the manufacturers of other
devices to determine their
compatibility with this device.

4
Copyright © 2009 Nokia. All rights reserved.
Get started
The headset contains the following
parts shown on the title page:
volume key (1), sliding boom (2),
earpiece (3), indicator light (4),
power key (5), charger connector
(6), mute key (7), answer/end key
(8), and microphones (9).
Before using the headset, you must
charge the battery and pair the
headset with a compatible device.
Compatible chargers
This device is intended for use when
supplied with power from the
following chargers: AC-6 and DC-6.
The exact charger model number
may vary depending on the type of
plug. The plug variant is identified
by one of the following: E, EB, X, AR,
U, A, C, or UB.
Charge the battery
1. Connect the charger to a wall
outlet.
2. Lift the cover of the charger
connector, and connect the
charger cable to it (10). The red
indicator light is displayed
during charging.
Charging the battery fully may
take up 35 minutes with the AC-
6 charger. Charging the battery
with the AC-6 charger for 15
minutes provides up to 5 hours
of talk time.
3. When the battery is fully
charged, the green indicator
light is displayed. Disconnect the
charger from the headset, then
from the wall outlet. Push the
cover over the charger
connector.

5
Copyright © 2009 Nokia. All rights reserved.
To charge the headset with a
compatible Nokia charger that has a
2.0 or 3.5 mm charger plug, use the
Nokia Charger Adapter CA-146C
(sold separately).
To charge the battery through the
USB port of a compatible PC,
connect one end of the Nokia
Connectivity Cable CA-101 (sold
separately) to the charger connector
and the other end to the USB port.
The fully charged battery has power
for up to 8 hours of talk time or up
to 160 hours of standby time.
To check the battery charge when
the headset is not connected to a
charger, press the power key when
the headset is switched on. If the
indicator light is green, the charge
level is sufficient. If the light is
yellow, you may need to recharge
the battery soon. If the light is red,
recharge the battery.
When the battery charge is low, the
headset beeps every 5 minutes and
the red indicator light flashes.
Switch on or off
To switch on, press and hold the
power key for about 2 seconds. The
headset beeps, and the green
indicator light is displayed. The
headset tries to connect to one or
two last connected devices. When
the headset is connected to a device
and is ready for use, the blue
indicator light flashes slowly. If the
headset has not been paired with a
device, it automatically enters
pairing mode.
To switch off, press and hold the
power key for about 2 seconds. The
headset beeps, and the red indicator
light is briefly displayed. If the
headset is not connected to a device
within 30 minutes, it switches off
automatically.

6
Copyright © 2009 Nokia. All rights reserved.
Pair and connect the headset
Before using the headset, you must
pair and connect it to a compatible
device.
You can pair the headset with up to
eight devices, but you can connect
it to only up to two devices at a
time.
1. Ensure that your mobile device is
switched on and the headset is
off.
2. If the headset has not been
previously paired with a device,
switch on the headset. The
headset enters pairing mode, and
the blue indicator light starts to
flash quickly.
If the headset has been
previously paired with a device,
ensure that the headset is
switched off, and press and hold
the power key for about 5
seconds until the blue indicator
light starts to flash quickly.
3. Activate the Bluetooth feature
on your device, and set it to
search for Bluetooth devices. For
details, see the user guide of your
device.
4. Select the headset from the list
of found devices.
5. If necessary, enter the passcode
0000 to pair and connect the
headset to your device.
In some devices, you may need to
make the connection separately
after pairing.
When the headset is connected to
at least one device and is ready for
use, the blue indicator light flashes
slowly.
To manually connect the headset to
one or two last used devices, press
and hold the answer/end key for
about 2 seconds (when no devices

7
Copyright © 2009 Nokia. All rights reserved.
are connected), or make the
connection in the Bluetooth menu
of the desired device. If you have a
device connected to the headset
and want to connect a second
device, make the connection in the
Bluetooth menu of the device.
You may be able to set your device
so that the headset connects to it
automatically. To activate this
feature in a Nokia device, change
the paired device settings in the
Bluetooth menu.
Basic use
Change the earplug
The headset may be provided with
different sized earplugs. Select the
earplug that fits the best and is the
most comfortable for your ear.
To change the earplug, pull the
current earplug from the earpiece
(11), and push the new earplug into
place (12).
Place the headset on the ear
Place the headset over your ear in a
comfortable position, and slide it
downwards (13). Gently push the
earpiece into your ear. Point the
headset toward your mouth.
Sliding boom
The sliding boom brings the
microphone closer to your mouth,
which improves the audio quality
when you talk at a lower volume or
in a noisy environment. You can use
the boom to answer or end a call.

8
Copyright © 2009 Nokia. All rights reserved.
To use the boom, gently pull it down
toward your mouth (14), or push it
up to its initial position (15).
Adjust volume
The headset automatically adjusts
the volume according to ambient
noise. To manually adjust the
volume, slide the volume key up or
down. To adjust the volume quickly,
slide and hold the key.
The selected volume level is saved
for the device that you currently use
with the headset.
Calls
To make a call, use your mobile
device in the normal way when the
headset is connected to it.
To redial the number you last called
(if your mobile device supports this
feature with the headset), when no
call is in progress, press the answer/
end key twice.
To activate voice dialling (if your
mobile device supports this feature
with the headset), when no call is in
progress, press and hold the answer/
end key for about 2 seconds.
Proceed as described in the user
guide of the mobile device.
To answer a call, pull the boom
completely down toward your
mouth, or press the answer/end key.
(For noise cancellation, the boom
has to be completely pulled down.)
To reject a call, press the answer/
end key twice.
To end a call, push the boom up to
its initial position, or press the
answer/end key.
To mute the microphone, slide the
mute key toward your mouth. To
unmute the microphone, slide the
mute key to the opposite direction.
When you mute or unmute the

9
Copyright © 2009 Nokia. All rights reserved.
microphone, the headset beeps
twice.
To switch a call between the
headset and a compatible
connected device, press and hold
the answer/end key for about 2
seconds.
Allow connection to two
devices
You can have the headset connected
to two devices at the same time.
By default, the headset can only be
connected to one device at a time.
To allow the headset to connect to
two devices, switch off the headset,
and press and hold the power key,
and slide and hold the volume key
up for about 5 seconds. The blue
indicator light flashes twice.
To allow the headset to connect to
only one device, switch off the
headset, and press and hold the
power key, and slide and hold the
volume key down for about 5
seconds. The green indicator light
flashes twice.
If the headset can connect to two
devices at the same time and you
use redialling or voice dialling, the
call is made on the device that you
last used to make a call when the
headset was connected to it.
Clear settings or reset
To clear all the pairing settings from
the headset, switch off the headset,
and press and hold the power key
and the answer/end key at the same
time for about 5 seconds. The
headset beeps twice, and the red
and green indicator lights alternate.
After the settings are cleared, the
headset enters pairing mode.
To reset the headset if it stops
functioning, even though it is
charged, connect the headset to a

10
Copyright © 2009 Nokia. All rights reserved.
charger, and press the power key
and the answer/end key at the same
time.
Troubleshooting
If you cannot connect the headset
to your compatible device, check
that the headset is charged,
switched on, and paired with the
device.