Nortel Secure Router 4134 User manual

Nortel Secure Router 2330/4134
Installation — Hardware
Components
Release: 10.2
Document Revision: 03.01
www.nortel.com
NN47263-301
.

Nortel Secure Router 2330/4134
Release: 10.2
Publication: NN47263-301
Document release date: 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
While the information in this document is believed to be accurate and reliable, except as otherwise expressly
agreed to in writing NORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF
ANY KIND, EITHER EXPRESS OR IMPLIED. The information and/or products described in this document are
subject to change without notice.
Nortel, Nortel Networks, the Nortel logo, and the Globemark are trademarks of Nortel Networks.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation.
ATTENTION:
Before unpacking, installing, or using the Secure Router 2330/4134, ensure you read the section about
regulatory information and general safety precautions in the first chapter of this guide.
All other trademarks are the property of their respective owners.
.

3
.
Contents
Secure Router 2330/4134 regulatory information and safety
precautions 7
Safety requirement for handling and installing modules 7
Types of notices 7
Cautions and warnings for the Secure Router 2330/4134 8
Foreign Exchange Station (FXS) Interface Modules 9
Foreign Exchange Office (FXO) Interface Modules 10
Personal safety and equipment protection 10
Module protection 10
Cables and connectors protection 10
Electrostatic discharge 11
Antistatic material 11
New in this release 13
Features 13
Secure Router 2330 hardware 13
Introduction 15
Prerequisites 15
Navigation 15
Nortel Secure Router 2330/4134 hardware components
fundamentals 17
Navigation 17
Secure Router 4134 Power supply units 17
Secure Router 4134 Fan tray 19
Interface modules for the Secure Router 2330/4134 20
T1/E1 Small Module 21
ISDN BRI S/T and ISDN BRI U Small Modules 23
Serial Small Module 26
FXS Small Module 29
FXO Small Module 31
T1/E1 Medium Module (supported on Secure Router 4134 only) 33
HSSI Medium Module (supported on Secure Router 4134 only) 34
CT3 Medium Module (supported on Secure Router 4134 only) 34
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

4
DS3 Medium Module (supported on Secure Router 4134 only) 35
GbE Medium Module (supported on Secure Router 4134 only) 36
FE and FE/PoE Medium Module (supported on Secure Router 4134 only) 38
Mediation Server Module for OCS (supported on Secure Router 4134 only) 40
Voice Carrier Medium Module (supported on Secure Router 4134 only) 42
GbE Large Module (supported on Secure Router 4134 only) 43
ADSL2+ Small Module 44
Secure Router 4134 Internal hardware components 46
DDR SO-DIMM 47
VPN/IPSec module 48
Internal PVM 48
Internal system compact flash 49
Hot swapping Secure Router 4134 hardware components 50
Compatible internal modules for Secure Router 2330 51
Replaceable parts for Secure Router 2330 52
Installing Secure Router 2330/4134 hardware components 55
Navigation 55
Installing the interface modules 56
Prerequisites 57
Installing a Small Module 58
Installing a Medium Module on the Secure Router 4134 58
Installing a Large Module on the Secure Router 4134 59
Installing a Small Module in the Secure Router 4134 Voice Carrier Medium
Module 60
Hot swapping interface modules 61
Prerequisites 62
Connecting Secure Router 2330/4134 power cables 63
Connecting AC power cables 63
Connecting DC power 64
Connecting the console port cable 67
Prerequisites 69
Installing or replacing a Secure Router 4134 power supply module 69
Prerequisites 70
Replacing a Secure Router 4134 fan tray module 71
Prerequisites 71
Installing or removing the internal VPN/IPSec module on the Secure Router
4134 72
Installing the internal VPN/IPSec module 72
Removing the internal VPN/IPSec module 73
Installing or removing an internal PVM on the Secure Router 4134 75
Installing the internal PVM 76
Removing the internal PVM 79
Replacing the DIMM in the Secure Router 4134 81
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

5
Prerequisites 81
Installing or removing the DIMM on the Secure Router 4134 Mediation Server
Module for OCS 82
Installing a DIMM on the Mediation Server Module 83
Removing a DIMM from the Mediation Server Module 85
Replacing the Secure Router 4134 internal Compact Flash 86
Prerequisites 87
Removing the Secure Router 2330 top cover 88
Prerequisites 88
Installing or removing the internal SCIM module on the Secure Router 2330 89
Installing the internal SCIM module 90
Removing the internal SCIM module 91
Installing or removing the internal PVIM module on the Secure Router 2330 91
Installing the internal PVIM module 92
Removing the internal PVIM module 93
Replacing the Secure Router 2330 DIMM 94
Replacing the Secure Router 2330 internal Compact Flash 95
Environmental requirements 97
Interface connector pin assignments 99
Serial cable descriptions 107
DTE V.35 serial cable 107
DCE V.35 serial cable 108
DTE X.21 serial cable 109
DCE X.21 serial cable 110
DTE RS-449 serial cable 112
DCE RS-449 serial cable 113
DTE RS-232 serial cable 114
DCE RS-232 serial cable 115
DTE RS-530 serial cable 117
DTE RS-530A serial cable 118
Hardware reliability 121
Battery life expectancy on the Mediation Server Module for OCS 123
Translations of safety messages 125
Class A device caution statement translations 125
Qualified service personnel warning statement 126
Overcurrent warning statement 126
Cover plate warning statement 127
Power cord warning statement 128
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

6
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

7
.
Secure Router 2330/4134 regulatory
information and safety precautions
Safety requirement for handling and installing modules
This section provides the information necessary for the proper and safe
handling of hardware components for the Secure Router 2330 and the
Secure Router 4134. Please read and apply this information to all aspects
of the instructions in this manual.
Types of notices
Notice paragraphs alert you about issues that require your attention. The
following paragraphs describe the types of notices used in this guide. For
translations of safety messages, see “Translations of safety messages”
(page 125).
ATTENTION
An attention notice provides important information regarding the installation and
operation of Nortel products.
CAUTION
ESD
ESD notices provide information about how to avoid discharge
of static electricity and subsequent damage to Nortel products.
CAUTION
Caution notices provide information about how to avoid possible
service disruption or damage to Nortel products.
WARNING
Warning notices provide information about how to avoid
personal injury when working with Nortel products.
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

8Secure Router 2330/4134 regulatory information and safety precautions
DANGER
Danger—High Voltage notices provide information about how to
avoid a situation or condition that can cause serious personal
injury or death from high voltage or electric shock.
DANGER
Danger notices provide information about how to avoid a
situation or condition that can cause serious personal injury or
death.
Cautions and warnings for the Secure Router 2330/4134
The following precautionary messages apply to the Secure Router
2330/4134. For your safety, read these precautions carefully before
proceeding with installation of the product.
WARNING
Only qualified service personnel must perform the installation.
Read and follow all warning notices and instructions marked on
the product or included in the documentation.
WARNING
This product relies on the building installation for overcurrent
protection. Ensure that a fuse or circuit breaker no larger than
120 V AC, 15 A U.S. (240 V AC, 10 A international) is used on
the phase conductors.
CAUTION
To reduce the risk of fire, use only number 26 AWG or larger
UL Listed or CSA Certified Telecommunication Line Cord for all
network connections.
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Hardware Notice
The Lithium battery in this product is part of a non-volatile memory device
and will retain data for 10 years in the absence of power. Nortel does not
consider the lithium battery in this unit a field replaceable or serviceable
part and should not be accessed by the customer.
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

Safety requirement for handling and installing modules 9
DANGER
Risk of injury by electric shock
Before working on this equipment, be aware of good safety
practices and the hazards involved with electrical circuits. Use
only power cords that have a grounding path. Ensure the switch
is properly grounded before powering on the unit.
WARNING
Risk of eye injury by laser
Fiber optic equipment can emit laser or infrared light that can
injure your eyes. Never look into an optical fiber or connector
port. Always assume that fiber optic cables are connected to a
light source.
CAUTION
If you do not install interface modules in slots, keep the metal
cover plates in place over the slots. Removing the cover plates
impedes airflow and proper cooling of the unit.
Foreign Exchange Station (FXS) Interface Modules
ATTENTION
Ensure you use standard straight-through RJ11 modular telephone cables with
FXS interface modules. TIP must connect to TIP and RING must connect to
RING. FXS ground start does not work if polarity is reversed.
ATTENTION
Nortel does not support FXS port connections leaving the building. Use FXS
connections for intra-building purposes only.
WARNING
The 2- and 4-port FXS interface modules have a ring signal
generator that is a source of hazardous voltage. Do not touch
the RJ11 port conductors, the conductors of a cable (that is,
the exposed metal ends of a cable connector) connected to
the RJ11 port, or the circuit board when the ringer is active (an
incoming call activates the ringer).
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.

10 Secure Router 2330/4134 regulatory information and safety precautions
Foreign Exchange Office (FXO) Interface Modules
ATTENTION
Ensure you use standard straight-through RJ11 modular telephone cables with
FXO interface modules. TIP must connect to TIP and RING must connect to
RING.
WARNING
The 2-port and 4-port FXO interface modules can receive a ring
signal that is a source of hazardous voltage. Do not touch the
RJ11 port conductors or the conductors of a cable (the exposed
metal ends of a cable connector) connected to the RJ11 port.
Personal safety and equipment protection
Read this section to prevent injury and equipment damage.
Module protection
The following practices prevent equipment damage when you work on the
Nortel Secure Router 2330/4134:
•Always wear a grounded antistatic wrist strap when you handle
modules.
•Always set modules on appropriate antistatic material.
•Handle modules by the faceplate and handles. Do not touch pins or
electrical connections.
•Do not leave interface module or power supply module slots empty.
You must fill all slots with modules or slot covers to maintain safety
compliance, proper cooling, and electromagnetic interference (EMI)
containment in the shelf.
•Ensure that your environment meets the requirements for temperature,
humidity, and cleanliness. See “Environmental requirements” (page
97).
•Do not overtighten thumb screws or lug nuts. Tighten screws and nuts
until they are snug, plus a quarter turn. If you use a power tool to
tighten screws, use a low torque setting of 2 to 3 in–lb (0.226 to 0.339
N-m).
Cables and connectors protection
The following practices prevent damage to cables and connectors:
•Use caution when connecting cables. Take care to ensure you insert
each cable connector in the correct port for the purpose you intend.
Nortel Secure Router 2330/4134
Installation — Hardware Components
NN47263-301 03.01 7 September 2009
Copyright © 2007-2008 Nortel Networks. All Rights Reserved.
.