NorthStar NS157310 User manual

Fully unpack the contents of the
pressure washer and lay out all
accessories .
Remove all product components &
review the instruction manual to
confirm all components have been
supplied with the product.
Remove the instruction manuals that
are located within the product battery
box. then read all safety & user
instructions carefully. Note: There are
two separate instruction manuals. One
for the motor & one for the pressure
washer.
Using a funnel, empty the entire
contents of the 2 bottles of engine oil
supplied with the product into the
motor crankcase, through the
dipstick hole. Check the oil level
before use.
Connect the RED ended cable to the
Positive (+) battery post & connect the
BLACK ended cable to the Negative (-)
battery post. Ensure the cable
connections are tight. Then place &
secure the battery into the battery box.
Assemble the Right handle using the
bolts & nuts supplied. Assemble the
L/H handle using the hose holder
bracket & nuts supplied.
With the assistance of a second
person, locate and install the wheels
onto the axles with the securing lock
rings. Use an Allen key to tighten the
locking ring fasteners.
Fill both fuel tanks located on the top of
the pressure washer, making sure you
put the correct fuel type into the
relevant fuel tank. Red tank- Unleaded
Petrol for Motor, Yellow tank- Diesel or
Kerosene Fuel for the heating burner.
Check and verify the pressure pumps oil level
by visually inspecting the pumps oil level sight
glass. Verify that the oil level is at least ½ way
up the sight glass & then remove the shipping
tape from the RED breather plug.
1 2 3
4 5 6
7 8 9
PART NO. NS157310
NorthStar 3000PSI Hot/Cold Water
Petrol Pressure Washer
THESE INSTRUCTIONS ARE TO BE USED AS A GUIDE ONLY AND ARE NOT INTENDED TO REPLACE THE FULL INSTRUCTION MANUAL PROVIDED WITH YOUR PRODUCT.
ALWAYS READ THE INSTRUCTION MANUAL FOR FULL DETAILS RELATING TO SAFETY INSTRUCTIONS, ASSEMBLY, OPERATION AND MAINTENANCE OF YOUR PRODUCT.
ALWAYS MAKE SURE YOUR PRESSURE WASHER IS ON STABLE LEVEL GROUND BEFORE CHECKING OIL LEVELS.
QUICK START GUIDE
Have questions relating to assembly or operation of your product, call KINCROME on 1300 657 528 Page 1/2
SCAN THE QR CODE WITH YOUR MOBILE DEVICE TO VIEW THE FULL SET UP & OPERATION VIDEO FOR THIS ITEM.

Install the supplied Orange 18mm
American BSP tap adaptor into the
water inlet.
DO NOT overtighten the tap adaptor
as this could cause damage to the
water inlet fittings .
Attach the high pressure hose onto
the pressure washers outlet
connector, assemble the pressure
gun & lance & connect the other end
of the high pressure hose onto the
pressure gun connector. Turn ON
your water supply.
Connect your 18mm water supply
hose onto the Orange tap adaptor
fitting.
Starting the motor can be achieved by
either pulling the recoil starter handle
repetitively or rotate the start key to the
start position for electric start. Once
started move the choke lever to the open
position.
The pressure washer is now ready to use
in cold water mode. Insert the preferred
nozzle for your application and you can
begin cleaning your job at hand.
Squeeze the trigger of the pressure gun
to purge all air from within the pressure
washers pump, heat exchange tank,
hoses & fittings. Continue until a
constant stream of water is visible.
Turn Fuel valve to the ON position,
rotate start key to ON position.
To operate the unit in HOT mode,
press/flick the heat switch to the ON
position, adjust the water temperature
thermostat to your required temperature.
While cleaning, the water will heat to your
required temperature during use.
If the engine is cold, slide the choke lever fully
to the left (closed choke) if the engine has
already been run or is warm then you may not
need to move the choke lever prior to starting.
11 12 13
14 15 16
17 18 19
PART NO. NS157310
NorthStar 3000PSI Hot/Cold Water
Petrol Pressure Washer
QUICK START GUIDE
Have questions relating to assembly or operation of your product, call KINCROME on 1300 657 528 Page 2/2
SCAN THE QR CODE WITH YOUR MOBILE DEVICE TO VIEW THE FULL SET UP & OPERATION VIDEO FOR THIS ITEM.
THESE INSTRUCTIONS ARE TO BE USED AS A GUIDE ONLY AND ARE NOT INTENDED TO REPLACE THE FULL INSTRUCTION MANUAL PROVIDED WITH YOUR PRODUCT.
ALWAYS READ THE INSTRUCTION MANUAL FOR FULL DETAILS RELATING TO SAFETY INSTRUCTIONS, ASSEMBLY, OPERATION AND MAINTENANCE OF YOUR PRODUCT.
ALWAYS MAKE SURE YOUR PRESSURE WASHER IS ON STABLE LEVEL GROUND BEFORE CHECKING OIL LEVELS.