NRS Healthcare M66406 User manual

Page 1 of 4
User Instructions
DIAG: 1
Support
Rail
Set
Screw
Wall
Stem
Towel
Rail
Contents
Description
Qty
Rail - c/w Wall stems, Self
Adhesive washers & Set
Screws 1
Screw (Suitable for solid walls
only) 3
Wall Plug (Suitable for solid
walls only) 3
Hex Key
1
Installation Instructions
1
General Safety Warning
Please ensure these instructions are fully
read and implemented. Failure to do so
may result in injury to the user. Retain in a
safe place for future reference.
Intended Use
This stylish Towel Rail with discreet
Integrated Grab rail has been designed to
compliment fittings in a contemporary
bathroom and provide a sturdy grab rail to
support and provide extra safety for the
user, it can be used on its own or part of
a group of products which combine and
compliment each other to provide a safer
environment for the user. Details of the
other products in the range are shown on
the last page of this leaflet
Unpacking
Remove the product from its packaging;
Check for damage. If you see any, or suspect
a fault, do not assemble the product; contact
your supplier immediately.
Code: M66406 –410mm (16”)
Code: M66569
–
610mm (24”)
2 In 1 Towel Rail with Integrated Grab Rail

Page 2 of 4
610
220
130 130
220
410
Diag:2
M66406 - 410mm (16")
M66569 - 610mm (24")
16
26
Safety Precautions
·This Towel Rail with Integrated Grab
Rail must be correctly assembled,
installed, and maintained.
·If installing the towel rail in a
showering or bathing area it may
need to be earthed to conform with
IEE Wiring regulations for metallic
components within bathrooms.
Consult a suitably qualified person
prior to installation
·Support rails can be slippery when
wet –use this product with caution.
·It is recommended that this product is
installed by a suitably qualified,
competent person.
·Only install the product in an area
where the mounting surface is
structurally sound. (Strengthening
modifications to the fixing surface
may be required.)
·
This product must be secured to the
wall using fasteners which are
appropriate to the structural base
material.
·The maximum Load of this product is
160kg (25st) based on the product
being fitted to a suitable surface using
appropriate fixings and fitted by a
competent person.
·The smaller under rail is not a weight
bearing surface.
·Waterproofing is recommended and all
fixings used should be none rusting. It
is recommended that sealant is
applied around the wall contact points.
If not properly sealed, there is the
potential for water ingress. This may
cause the wood to rot, compromising
the structure and safety of the support
rail
Installation General:
This product requires tools for
installation. A Hex Key is supplied for
the set screws.
The product is also supplied with
fixings suitable for solid walls only.
It is important the product is secured
to the wall using fasteners appropriate
to the structural base material.
Before installation; consider the best
place to position the rail, taking into
account all activities it may be used
for, e.g. sitting, standing, reaching.
Also consider the structure behind the
wall surface, avoid any
electrical/plumbing behind the wall
and, where possible, drill through a tile
rather than grout.

Page 3 of 4
Tighten
Set
Screws
DIAG: 5
Wall
Plug
Set
Screws
Rail
Socket
Fixing
Screw
DIAG: 4
DIAG: 3
Wall
Stem
11 - IMPORTANT NOTE: Perform a final tighten
and inspection of all fasteners.
12 - Test the installation by vigorously pulling on
the support rail. The rail should be rigid and
stable.
Care &Maintenance
Inspect on a regular basis the stability and
rigidity of the product, check all screws are
tightened and in good condition
Cleaning
·Clean regularly, wiping down with a soft
cloth and a mild detergent/disinfectant
solution
·Do not use abrasive cleaners
7 - Place the rail back onto the wall
stems. See diag. 4
8 - Secure rail by tightening the set
screws. See Diag 5
9 - The rail will pull into the stems as the
set screws are tightened.
10 - The rail will fit best if placed as
straight as possible over the wall stems.
If the rail sockets do not easily fit onto
the wall stems there is some movement
possible with the oversized hole in the
wall stems, the stems can be adjusted to
accommodate the rail sockets.
Installation Instructions:
1 - Position the rail in the proposed area
and mark accurately it's position,
ensuring it is level.
2 - Peel off the backing on the self
adhesive washers attached to the wall
stems (3 places)
3 - Push the rail firmly against the wall.
4 - Using the supplied hex-key, loosen
all set screws in the rail sockets so the
rail can be removed, leaving the threes
wall stems attached to the wall
5 - Mark the positions through the
centre of the wall stems, remove the
stems and drill three holes to the correct
size.
6 - Fit the wall plugs and fix the wall
stems to the wall using appropriate
fasteners and seal with suitable water
proofing

Page 4 of 4
UI/
M66406/M66569/06/13/Iss2
NRS Healthcare
Sherwood House, Cartwright Way, Forest Business Park, Bardon Hill, Coalville,
Leicestershire. LE67 1UB UK
Tel. Main Office: 0330 100 00 98
Tel. Customer Services: 0845 120 4522
Email: [email protected]
www.nrs
-
uk.co.uk
If you use this product…. You may also find the other products in our range
of bathroom grab rails useful.
2 In 1 Soap Dish
with Integrated Grab Rail.
Code: M66388
2 In1
Toilet Roll Holder
with Integrated Grab Rail.
Code: M66399
2 In 1 Corner Shelf
with Integrated Grab Rail.
Code: M66376
IMPORTANT
For information on how to obtain the User Instructions in other languages and formats
for use by people with visual, reading or cognitive impairments, please contact:
[e-mail]
or telephone [phone]. Additional copies of this user instruction are available on
our website:
www.nrs
-
uk.co.uk
.