NRS Healthcare N29210 User manual

1
USER INSTRUCTIONS
TRANSIT LITE ATTENDANT CONTROLLED
WHEELCHAIR
N29210 Transit Lite - Blue N43528 Transit Lite - Silver
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in
a safe place for future reference.
Maximum User Weight
17st
110kg
1. INTENDED USE
The Transit Lite Attendant Controlled Wheelchair is designed for use by a carer to transport a person both
indoor and outdoor, it can be easily folded for storage and transportation. It is not intended for use as a seat
in a motor vehicle.
2. SAFETY
Warning: The maximum user weight must not be
more than 110Kg (17st).
This Wheel chair is designed for single occupancy
only, do not use it to transport more than one person.
This wheelchair is designed for both indoor and
outdoor use, however special care should be taken
in certain environmental conditions.
Outdoor: Steep gradients should be avoided, where
possible.
If attempting gradients, or using a ramp it is important
to be sure of your own capabilities, NRS recommend
that you consult a Healthcare Professional for advice
before use.
Always maintain a constant slow speed on gradients.
Do not reverse down a gradient.
Avoid rugged/uneven terrain.
Indoor: Be aware of local hazards, for example,
obstructions on the floor, narrow doorways high
thresholds etc.
Do not use on escalators.
Before transferring into or out of the wheelchair
ensure the brakes are in the locked position.
Do not stand on the footplates.
When seated in the wheelchair ensure you are
comfortable and your centre of gravity is in the centre
of the seat.
Take care when performing tasks which move your
centre of gravity. Never reach so far that it requires
you to shift in the seat or bend forward over the
front wheels. If you do need to reach forward always
ensure the front wheels are facing outwards and are
locked before attempting any manoeuvre, this will
increase the wheels footprint.
Users feet must always be on the footplates when
the wheelchair is moving.
Take care when ascending or descending a kerb.
When mounting a kerb, approach forward facing, the
attendant should then use the stepper tubes, located
behind the rear axles, to raise the front wheels onto
the raised kerb, then roll the rear wheels up the kerb
lifting as required.
When descending a kerb the front wheels should
be lined up parallel with the front edge of the kerb,
then using the stepper tubes the attendant raises
the front wheels slightly to the balancing point of the
chair and then gently lower the rear wheels over and
down the kerb.
Do not raise the front wheels by using the handles
only - Always use the stepper tubes.

2
If you need to stop on an incline apply both brakes
gently, avoid sudden movements, similarly when
starting avoid sudden movements as both of these
situations could cause instability because of the
backward angle of the chair.
Apply brakes evenly as any movement sideways
could cause instability.
Avoid changing direction on a slope as this will
increase the risk of the wheelchair tipping.
Do not use as seat in a motorised vehicle.
If you are unsure about any of the safety precautions
highlighted we would recommend seeking advice
from a Healthcare professional.
3. UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are
missing or damaged and do not try and assemble.
3.1 Contents:
1. Wheelchair (folded)
2. Calf Strap
3. Footrest Assembly (x2)
4. Multi Function Spanner
5. Allen Key
6. User Instructions
4. SPECIFICATION
Maximum User Weight: 110kg (17st)
Product Weight: 11.65kg (25.5lbs)
5. ASSEMBLY/INSTALLATION
Unfold the wheelchair from its packed (folded) state,
ensure all four wheels are touching the floor and the
seat is fully opened.
Raise the hinged handles to the upright position until
the spring pins “click” and lock into position on both
sides.
Assemble the footrests to the chair frame by
engaging the holes in the footrest bracket onto the
two hinge pins on the frame, this can be done more
easily if the footrest is pointing outwards, at a right
angle with the chair side. Rotate through 90 degrees
until the chrome footrest clip springs into position.
When using for the first time, it is important to
ensure the correct seating position, this may need
the footrest height to be adjusted. To do this slacken
the hexagon head screw, on the underside of each
footrest, with the spanner (provided). Slide the inner
tube up or down to the required position and retighten
Fit the calf strap as shown and secure with the hook
and loop fasteners.
Check the brakes are functioning correctly. If not,
refer to the maintenance section for correct brake
adjustment.
The wheelchair is now ready to use.
6. IN USE
6.1 Folding the wheelchair
Ensure footrests are facing forward and footplates
are in the upright position, then simply pull up the
two handles on either side of the seat, see picture
above, the wheelchair can be carried using these
handles.
For transportation and storage it is recommended
that the footrests are removed & the handles are
folded down.
Remove the Calf Strap by pulling apart the hook and
loop fasteners.
Footrest removal: pull the chrome footrest clip
towards the centre of the wheelchair and lift the
footrest offthe locating pins.
Handle folding: Pull the two plastic handle clips
backwards and fold the handles.
6.2 Brake operation

3
To apply the parking brakes, push down both handles
until they lock, see diagram 3B, The brakes will click
and remain in the locked position until released.
It is important that both brakes are in the parking
(locked) position when they are used.
Lift up both handles to release the parking brakes.
When using the brakes to slow down, pull up both of
the loop handles. See diagram 3A.
If you apply the parking brake, or pull up the brake to
stop whilst moving, and the rear wheels still move,
stop use immediately. Do not use again until the
brakes have been checked and correctly adjusted.
Refer to the maintenance section.
7. MAINTENANCE
Note: all tyres on this wheelchair are solid and do
not need inflating.
Regularly check for wear and tear and that all screws
and fixings are securely fastened.
Worn upholstery must be replaced.
Check brakes are working satisfactorily, both for
slowing and by braking to a stop.
Check the parking brakes by pushing the handles
down into the locked position and then trying to push
the wheelchair.
If the brakes do not completely lock the wheels the
brakes need to be adjusted.
For correct adjustment, the brake mechanism, when
not in use, should not touch the wheel, but the gap
should be no greater than 3mm.
To tighten the brake (reduce the gap between brake
and wheel) rotate the adjusting nut clockwise. See
Diagram 4.
Diagram 4
Caution: After making any adjustments to the brakes,
you must test them before the wheelchair is used.
If adjustment does not tighten the brakes, do not
use the wheelchair Contact your dealer or NRS
Customer services.
8. CLEANING INSTRUCTIONS.
Clean all parts regularly, wipe down with water and
mild cleanser using a soft, non abrasive cloth.
Dry with a soft, clean, non abrasive, dry cloth.
Ensure there is no build up of dirt or debris around
the axle, brakes and wheels.
Do not use cleaning agents containing phenol or
chlorine, as this may damage the product surfaces.
Lubricate with 3-in-l oil periodically or if wheels begin
to squeak.
9. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period
of 12 months, from the date of purchase, against
faulty materials and workmanship.
This guarantee does not cover; fair wear & tear,
abuse, misuse, interference or tampering with any
part of the product.
Any guarantee issued by NRS Healthcare does not
affect your statutory rights.
If you have any problems with our products, please
contact us at the address below.
If you have experienced an injury, contact us but feel
free to contact the Medical and Healthcare products
Regulatory Agency at:
[email protected].uk

4
NRS HEALTHCARE Sherwood House,
Cartwright Way, Forest Business Park, Bardon
Hill, Coalville, Leicestershire, LE67 1UB, UK.
NRS HEALTHCARE 4C Altona Road, Blaris
Industrial Estate, Lisburn, Co Antrim,
Northern Ireland BT27 5QB
Tel: Customer Services: 0345 121 8111 Email: [email protected]
NRS Healthcare is a leading supplier of community equipment and daily living aids.
Please visit one of our websites to view our full range of products:
www.healthcarepro.co.uk or www.completecareshop.co.uk
N29210-UI-3 26-07-2021