NRS Healthcare N72838 User manual

User Instructions - N72838
NRS Aluminium Swivel Bath Seat
Maximum
User
Weight
Intended Use
This Swivel Bath Seat is designed to enable a
user of limited mobility to rotate, whilst seated,
into the bath to allow seated washing. It is
suitable for most standard baths but is not
suitable for corner baths, baths which have
uneven / profiled top edges or some baths
with deeply moulded side panels. The frame
can be adjusted to fit most common bath
sizes.
Specification
Support Frame width 660-760mm
Seat Width: 460mm
Max User Weight: 160 Kg (25st)
Safety Precautions
Check all fixings are installed correctly
When placing on the bath ensure all four
feet of the bath seat mounting frame are
resting on the edge of the bath by at least
50mm (2”)
Check the Handwheel screws are
contacting either side of the bath wall. Do
not over tighten the handwheels as this
could damage the bath.
Do not exceed the maximum user weight
limit.
Always sit in the centre of the seat
Do not lean on the edges of the seat
Do not stand on the seat or any other part
of the product
Inspect at regular intervals, see care and
maintenance section
General Safety Warning
Please ensure these instructions are fully
read and implemented. Failure to do so may
result in injury to the user. Retain in a safe
place for future reference.
Contents List
1 - Seat Assembly 1
2 - Armrest 2
3 - Mounting Frame 2
4 - Fixing e-clips 4
User Instruction 1
NRS Healthcare,
Sherwood House, Cartwright Way, Forest Business Park,
Bardon Hill, Coalville, Leicestershire, LE67 1UB, United Kingdom.
Tel. Head Office: 0330 100 0098
Tel. Customer Services: 0345 121 8111
Email: [email protected]
1
3
2
4
Diagram: 1

Cleaning Instructions
The swivel Bath seat has a powder coated
aluminium frame with a moulded
polypropylene seat. Clean all parts regularly,
wiping down with a mild detergent /disinfectant
solution. Avoid the use of abrasive cloths and
cleaners, as they can damage plastic parts.
Inspect the product regularly for signs of wear
or damage
Maintenance
Inspect the product at regular intervals, pay
particular attention to the swivel and lock
movement.
Check all fixings, ensure they are secure.
Check all parts for signs of wear or damage.
If the product is not moving freely or you
suspect a fault do not use –contact your
dealer immediately
Product Guarantee
NRS Healthcare, guarantee this product for a
period of 12 months from the date of purchase
against faulty materials and workmanship. This
guarantee does not cover, abuse, misuse,
interference or tampering with any part of the
product.
Any guarantee issued by NRS Healthcare
does not affect your statutory rights
This product is part of a range of over 3000
daily living aids available from NRS
Healthcare.
To view the full range, please visit our website,
or request a catalogue by calling NRS
Healthcare.
www.nrshealthcare.co.uk
UI/N72838/05/17/Iss2
Using the Bath Seat

Raise the locking handle (F) and rotate
until the seat is facing the user, lower the
handle and lock into position.

Transfer user into seat. Raise locking
handle and rotate slowly into bath, taking
care when raising legs over the side of the
bath.

Ensure seat is locked into position and no
longer rotates freely before commencing
washing.
Care & Maintenance
It is recommended the product is wiped down
after use, or at regular intervals to maintain
the quality finish –see cleaning instructions
Assembly and Installation
Remove all parts from the packaging and check
they are not damaged. If you see, or suspect a
fault, do not use, contact your dealer
immediately.
Product Assembly
Slide each armrest (A) into the locating tubes on
the seat assembly until the spring button clips
“snap” into position, see diagram 2
Slide the mounting frame (B) into the locating
tubes on the seat assembly, note the frame is
width adjustable, choose the correct width to suit
your bath. Please refer to the instruction for
correct fitting
Assembling to a bath
Place the seat onto flat bath ledges.
IMPORTANT: At least 50mm (2") of ALL the
mounting frame feet (C) must rest on the flat
sides of the bath
If necessary extend the mounting frame by
removing the fixing e-clips (D), adjusting the
width of the frame so that it is closest to the
external width of the bath and replacing the
clips, check they are all replaced and secured
correctly.
Secure the mounting frame using the clamps
(E) under the seat by turning the hand wheels
until secure against the walls of the bath on
both sides. Check the frame is secure, but do
not over tighten as this could damage the bath.
The bath seat is now ready for use
Safety Note: If the Seat is removed and
replaced over the bath, it is important the fixing
clamps are re-adjusted and tightened as
detailed above
B
C
D
E
F
B
Diagram 2
Diagram 3
A
A